Sealey LED307 User manual

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL
Ensure the lamp is fully charged before initial use.
 DO NOT turn the lamp on when it is being charged.
 DO NOT shine directly into your, other person’s or
animal’s eyes.
 DO NOT allow children to use the lamp.
 DO NOT handle or move the lamp whilst it is being
charged.
 DO NOT use the lamp if you suspect that the battery or
the lamp casing is damaged.
DO NOT leave battery in a discharged state, recharge
battery immediately. Before storage, fully recharge the
battery, subsequently recharge the battery at least once
every six months of non-use.
1.2. ELECTRICAL SAFETY FOR USE OF CHARGER.
USE ONLY THE SUPPLIED CHARGER PLUG FOR
CONNECTING LAMP TO THE POWER SUPPLY.
 WARNING! It is the user’s responsibility to read,
understand and comply with the following electrical
instructions:
You must ensure the risk of electric shock is minimised
by the installation of appropriate safety devices.
An RCCB (Residual Current Circuit Breaker) should be
incorporated in the main distribution board. We also
recommend that an RCD (Residual Current Device) is
used with all electrical products, particularly portable
equipment which is plugged into an electrical supply not
protected by an RCCB.
You must also read and understand the following
instructions concerning electrical safety.
1.2.1. The Electricity At Work Act 1989 requires all portable
electrical appliances, if used on business premises, to be
tested by a qualified electrician, using a Portable
Appliance Tester (PAT), at least once a year.
1.2.2. The Health & Safety at Work Act 1974 makes owners
of electrical appliances responsible for the safe condition
of the appliance and the safety of the appliance operator.
If in any doubt about electrical safety, contact a
qualified electrician.
1.2.3. You must ensure that you:
Inspect the charger plug, cable and connector for wear
and damage to ensure items are safe before connecting
to the mains power supply.
If worn or damaged DO NOT use.
Important: Check that the voltage marked on the charger
plug is the same as the lamp.
Uncoil the cable between charger and the lamp.
 DO NOT pull the charger plug from the mains socket by
the lead.
 WARNING! DO NOT use any other type of charger with
this product, other than the supplied mains or car
charger. Failure to observe this warning could result in
injury and or fire and will invalidate the warranty.
 DO NOT try to take the charger plug apart.
 DO NOT use the charger plug to charge or power any
other electrical item.
 DO NOT get the charger wet, or use in wet, damp
conditions (for indoor use only).
1.3 Battery Safety
 WARNING! To reduce the risk of burns or fire:
 DO NOT Attempt to open, disassemble, modify or
service the battery pack.
 DO NOT Crush, puncture, short external contacts or
dispose of in fire or water.
 DO NOT Expose to temperatures above 60°C (140°).
 Replace only with the battery pack designated for this
product.
 Recycle or dispose of used battery as stipulated by local
regulation.
 If the electrolyte in the cells gets on your skin, thoroughly
wash with soap and water. If it gets in your eyes, rinse
thoroughly with cool water and seek immediate medical
attention
Heavy-duty housing features 37 super bright LEDs. 30 LEDs used as an inspection lamp or 7 LEDs in the end for use as a
directional torch. 360° Hanging hook and magnet on rear of lamp for hands-free applications. Single LED battery indicator.
Supplied with 12V in-car charger and mains charger.
Battery: ..............................................................3.6V / 1200mAh
Charging Time: .....................................................................5hrs
Operating Time:....................................................................5hrs
Length..............................................................................210mm
2. INTRODUCTION / SPECIFICATION
INSTRUCTION MANUAL FOR:
CORDLESS 30 + 7 LED RECHARGEABLE
INSPECTION LAMP
MODEL No: LED307
Original Language Version LED307 Issue: 2 - 25/10/11

3. CHARGING
4. OPERATION
Note: LED arrays are designed to allow individual LEDs to cease functioning
without causing the entire array to fail. This could be as a result of shock or
impact. Shock or impact will invalidate warranty.
4.1 Direct the lens away from your eyes before switching on.
Their are two buttons in the switch the top button with an upward facing
arrow turns on the 7 LED array on the top of the lamp. The downward facing
arrow turns on the 30 LED array. See Fig.1.
4.2 Suspend the lamp by the hanging hook. When the lamp is hanging from the
hook it can be rotated through 360° for more precise positioning.
4.3 Alternatively use the integral magnet on the rear of the lamp (Fig.2) to attach
to any ferrous surface.
Note: Fully charge the lamp before first use.
3.1 Connect the charger into the charging port (Fig.1) on the bottom of the lamp.
Plug into power supply and turn on, the charging LED (Fig.1) will light
RED to show charging has commenced.
3.2 When the battery has fully charged the LED will change to GREEN.
Environmental Protection.
Recycle unwanted materials instead of disposing of them as waste.
All tools, accessories and packaging should be sorted, taken to a
recycle centre and disposed of in a manner which is compatible with the
environment.
When the product is no longer required, it must be disposed of in an
environmentally protective way.
Battery Removal
Remove the 4 screws on the back of the lamp (Fig.2) and the four
screws on the top of the lamp surrounding the 7 LED array. Remove the
back casing, and disconnect the wiring to the charger port and from the
battery to the circuit board. Dispose of batteries according to local
authority guidelines.
5. MAINTENANCE
5.1 Keep the inspection lamp free from dirt and grease, use a damp cloth and a
mild detergent. Do not submerge the lamp in water or subject it to any acids
or detergent that may degrade the materials of the lamps construction.
Fig.1
Fig.2
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
[e-mail]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to
www.sealey.co.uk, email [e-mail] or phone [phone].
Original Language Version LED307 Issue: 2 - 25/10/11
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd
are required to inform potential purchasers of products containing batteries (as
defined within these regulations), that they are registered with Valpak’s
registered compliance scheme.
Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705