UNIVIEW OET-213H-BTS1 User manual

V1.00
Face Recognition Access Control Terminal
Quick Guide

Contents
1Packing List ······················································································································1
2Product Overview············································································································1
2.1 Appearance and Dimension ···············································································2
2.2 Structure Description···························································································3
3Device Installation ···········································································································4
3.1 Installation Environment ·····················································································4
3.2 Device Wiring ·····································································································4
3.3 Tools Preparations·······························································································6
3.4 Installation Steps ·································································································6
4Device Startup ·················································································································8
5Web Login························································································································9
6Personnel Management ··································································································9
7Appendix························································································································10
7.1 Face Recognition Precautions············································································10
7.1.1 Face Photo Collection Requirements ····················································10
7.1.2 Face Match Position ··············································································11
7.1.3 Face Match Posture···············································································11
Disclaimer and Safety Warnings ·······················································································13

1
1Packing List
No.
Name
Qty
Unit
1
Face recognition access control terminal
1
PCS
2
Screw component
1
Set
3
Bracket
1
PCS
4
T10 box-end wrench with hole-L shape
1
PCS
5
Installation sticker
1
PCS
6
20-pin cable
1
PCS
7
2-pin power cable
1
PCS
8
User manual
1
PCS
2Product Overview
The face recognition access control terminal features high performance and high
reliability. It perfectly integrates UNV face recognition technology, and supports
face scanning-based verification and door opening by relying on the deep learning
algorithm, thereby implementing accurate control of personnel access. Visitors
can call the indoor unit of a resident so that the resident opens the door remotely.
The product is highlighted by high recognition rate, large storage capacity, and fast
recognition. The access control terminal also supports attendance, and other
functions. It can be widely applied in building systems in smart communities,
public security, campuses, and other similar scenes.

2
2.1 Appearance and Dimension
The actual device appearance shall prevail. The figure below shows the dimension
of the device.
A waterproof hood is required in waterproof installation. The figure below shows
the dimensions of the waterproof hood.

3
2.2 Structure Description
The figure below shows the structure of the device. The actual device shall prevail.
Figure 2-1 Device Structure
1.Light supplement lamp 1
2.Infrared camera
3.Infrared light supplement lamp
4.Visible light camera
5.Light supplement lamp 2
6.Display screen
7.Pass-through indicator
8.Microphone
9.Card reading area
10.Loudspeaker
11.Reset button
12.USB2.0
13.Network interface
14.Power input (DC 12V±25%)
15.20-pin interface
16.Tamper proof button
1
2
3
4
5
6
7
9
13
14
15
16
8
10
11
12

4
3Device Installation
3.1 Installation Environment
Try to avoid intense direct light and intense backlighting scenes when installing
the device. Please keep the ambient light bright.
3.2 Device Wiring
1Wiring Embedding
Before installing the face recognition access control terminal, plan the layout of
cables, including the power cable (for the diameter selection for the extension
power cable, see Table 3-1), network cable, door lock cable, Wiegand cable, alarm
cable, and RS485 (RS232) cable. The number of cables depends on the actual
networking conditions. For details, see Wiring Description.
Table 3-1 Diameter Selection Table for Extension Power Cables
DC 12V/2A for power supply; the lower limit for the operating voltage is DC 9V (12V-25%)
Wire Diameter (mm)
0.8mm
1mm
1.25mm
1.63mm
(20AWG)
(18AWG)
(16AWG)
(14AWG)
Transmission Distance (m)
18
37
58
99
2Wiring Description
The figures below show the wiring between the access control terminal and
different devices. For the wiring terminal of each device, see the operation
manual of the device or consult related manufacturers.
NOTE!
In the wiring schematic diagrams, input devices and output devices are defined as
follows:
Input devices refer to devices that send signals to the access control terminal.
Output devices refer to devices that receive output signals from the access
control terminal.

5
Figure 3-1 Wiring Schematic Diagrams (without Security Module)
The face recognition access control terminal can be also connected to a security
module. The figure below shows the wiring of the security module.
Figure 3-2 Wiring Schematic Diagrams (with Security Module)
Power input
Alarm input
Alarm output
RS485
Wiegand output
Wiegand input
Door lock
VDD12V RED
GND BLACK
+12V
GND
GND BLACK
ALARM_IN1 WHITE/BLUE
ALARM_IN0 WHITE/GREEN
ALARM_OUT_NO WHITE/ORANGE
ALARM_OUT_NC GREEN
ALARM_OUT_COM WHITE/PURPLE
RS485_P ORANGE
RS485_N PURPLE
GND BLACK
WG_IN_D0 WHITE/BLACK
WG_IN_D1 WHITE/RED
GND BLACK
WG_OUT_D0 BLUE
WG_OUT_D1 RED
+-
LOCK_NC GREY
LOCK_COM WHITE
LOCK_NO BROWN
GND BLACK
SEN_ IN WHITE/BROWN
BUTTON_IN WHITE/YELLOW
PRESS
TO EXIT
+
+
-
-
+-
Face Recognition Access Control Terminal
-+
USB2.0
Network interface
USB drive
Card
reader
Door opening button
Cathode lock
Door status
switch
Power supply
Anode lock/Magnetic lock
Access
controller
Power
supply
Wiegand
card
reader
Alarm output
device
Alarm output
device
Alarm input
device
Alarm input
device
Power
supply
Digital Detection
Module
RS485
LOCK_NC YELLOW
LOCK_COM PURPLE
LOCK_NO GREY
GND BLACK
SEN ORANGE
BUTTON WHITE
PRESS
TO EXIT
+
+
-
-
+-
VDD12V RED
GND BLACK
+12V
GND
Alarm input
device
GND BLACK
ALM_IN1 RED
RS485_P ORANGE
RS485_N PURPLE
485_P BLUE
485_N BROWN
Face Recognition Access Control Terminal
Power input
Door lock
Alarm input
Door opening button
Cathode lock
Door status
switch
Anode lock/Magnetic lock
Power
supply
Gated Security
Module

6
3.3 Tools Preparations
Phillips screwdriver
Antistatic wrist strap or antistatic gloves
Drill
Tape measure
Marker
Plenty of silicone rubber
Silicone gun
3.4 Installation Steps
1. Determine the position of the 86*86mm
wall-mounted junction box.
This installation mode embeds an
86*86mm junction box in the wall in
advance or makes a hole on the wall to
embed the box.
NOTE!
There are two installation holes on the 86*86mm
wall-mounted junction box. They can be parallel
to the ground or vertical to the ground. They
need to map to intermediate holes on the bracket
during actual installation.
2. Determine the positions of holes on
the wall by referring to the positions
of four holes A on the installation
sticker.
Wall
Determine
the positions
of installation
holes on the
wall based
on the four
holes A.

7
3. Use a drill to drill two holes with the
depth of 30mm and diameter of 6mm to
6.5mm on the wall.
Note：
Avoid embedded wires in the wall during drilling!
4. Embed expansion bolts inside the
two installation holes on the wall.
5. Bracket.
Normal Installation：Align holes on the bracket with installation holes on the wall
and the 86*86mm wall-mounted junction box and use the Phillips screwdriver to
tighten the screws clockwise to fasten the bracket.
Waterproof Installation：The waterproof installation process is basically the same
as the normal installation process. You need to fasten the bracket and waterproof
hood together, for detail, see figure below. After the waterproof installation is
completed, apply enough silicone rubber along the gap between the edge of the
waterproof hood and the wall(left, top and right). Silicone rubber must be
continuous.
(without waterproof hood) (with waterproof hood)
Wall
Wall

8
6. Fasten the access control terminal to the
bracket hook.
7. At the bottom of the device (dotted
box as shown in the figure below),
use the L-shape wrench to tighten
the two fastening screws clockwise.
4Device Startup
After the device is installed correctly, connect one end of the power adapter
(purchased or prepared) to the mains supply and the other end to the power
interface of the face recognition access control terminal, and then start the device.
The display screen of the outdoor monitor is energized and lights up, and the live
view is displayed on the screen, indicating that the device is started successfully.