Uniwell AX-3000 series User manual

[AX3000] USR-005
2012-09-28
……..…..
AX-3000 series
Users Manual
……..…..
THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND
SHALL BE EASILY ACCESSIBLE.
LA PRISE DOIT ETRE PRES DE L'APPAREIL ET FACILE D'ACCES.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
!

CONTENTS
Attention................................................................................................ 1
I. Introduction...................................................................................... 2
Main Features...................................................................................................................2
Parts Names......................................................................................................................3
Hardware Specifications...................................................................................................4
II. Installation and Remarks .............................................................. 5
Precautions to use this POS safely ...................................................................................5
Remarks............................................................................................................................6
How to Clean the Cabinet and Touch Screen...................................................................9
In case of the power failure..............................................................................................9
In case if POS is locked down..........................................................................................9
Notes:
1. The contents of this manual are subject to change without notice.
2. Uniwell cannot be held responsible, if other products which are not approved by Uniwell, are
used for options or expendable supplies.

1
Attention
Thank you very much for purchasing our POS terminal. This POS has many
programmable features, hardware combinations and options. Please consult your
dealer as to your particular requirements, as this POS can be configured to suit a
variety of different applications.
Please fill data in the blanks below;
MODEL:
(Please see the label on the machine.)
SERIAL No:
(Please see the label on the machine.)
DATE OF PURCHASE:
YOUR DEALER:
(where purchased)
Manufacturer Uniwell Corporation
4-32, 1-chome, Doshin, Kita-ku, Osaka, 530-0035, JAPAN
http://www.uniwell.com/
Contact within
EU community DDS – Daon Data Systems GmbH 1-K, 63110 Rodgau, Germany
http://www.daon.de

2
I. Introduction
This model is New generation of Touch Screen POS terminals for Restaurants, Bars
/ Pubs and Fast-food stores having a lot of functions.
Main Features
 New Generation of POS terminal with high-speed CPU and Real Time OS
Solid-state technology (No moving parts, No Hard Disk, No fan) offers reliability
and stability of Embedded system.
It offers: Speedy operation, Instant power on/off, Security from virus attack and
hacking and Longer lifetime with lower maintenance.
 User friendly quick and intuitive programming and operation with rich GUI
 Remote access/control via internet:
Remote firmware update and preset data modification, Sales report via internet
 SD card / USB memory stick interface for:
Collection of report data, EJF data (& backup by SD card)
Upload/download preset data and graphic images
Firmware update
 Password security & security levels for sales, report and program.
 Graphical table plan
Table move, combine, split, creation and deletion can be done instantly at sales
mode. Table can show the information such as subtotal amount, table-opening
time/duration and customer name according to system option.
 Configurable button layout
For easy operation and easy programming, it employs Area concept for each
button type – PLU, PLU Page, PLU Page Group, Function, Function Page –
which is fully configurable.
Transaction window can be placed on either side according to customer
preference. Graphical image can be assigned to each button.
 Customizable print format for various bills, tickets, reports, etc.
 Stock management by Independent inventory list

3
Parts Names
Interface (bottom) and Main Power Switch for Emergency
Power ON switch Used to turn the power ON while the Main Power Switch is ON.
(Even if this switch is pressed, nothing happens while POS is turned ON.)
To turn off POS, touch Shutdown button on the screen.
Main Power Switch
for Emergency
Normally keep ON.
Used to turn the main power switch ON and OFF.
Turn OFF after the Shutdown operation is done when the peripherals are
connected to POS or POS is not used for a long time.
LED
Card Reader (option)
The swiping direction of
card reader is up to down.
Touch Screen
(angle adjustable from 0 to 70 degree)
Interface (side)
Power ON
Switch
Clerk iButton (option)
Ethernet
Type B
IR
Main Power
Switch
USB
USB USB DW2 DW1
LAN
COM 3
COM 4
COM 2 COM 1 DC12V
IN

4
Hardware Specifications
Processor (CPU) 32 bit ARM9 RISC Processor, 177 MHz
SDRAM 64 M Byte
Flash Memory 8 M Byte
Memory SRAM 8 M Byte
Touch Panel 15 inch 4 wire resistive type
Light load type, antifouling film
Operator Display 15 inch TFT XGA color
1024 (H) x RGB x 768 (V)
Adjustable angle: 0 ~ 70°
Customer Display (option) 20 digits x 2 lines (RS232C)
Dimension
Width: 366 mm, 396 mm with card reader
Depth: 306 mm, 332 mm with clerk iButton
Depth for LCD case: 83 mm
Height: 285 ~ 347 mm (varies depending on angle)
Footprint: 230 x 230 mm
Weight (kg) 6.8 Kg
System Power DC 12V/5A external power adapter
AC Power Source AC 100 to 240V, 50/60Hz
Interface
1 x Ethernet 10/100 Mbps
4 x RS232C (PC standard pin layout)
4 x USB host
1 x USB device (in future)
1 x SD card interface
2 x Cash drawer (24V drive)
Option
Customer display (RS232C)
Magnetic swipe card reader
Clerk iButton (Olitronic or Addimat)
2 cash drawers
Terminal printers
Temperature Operation : 0°~ 40°C (32°~ 104°F)
Storage : -10°~ 60°C (-14°~ 140°F)
Memory Protection 3 months

5
II. Installation and Remarks
Precautions to use this POS safely
 Should not be installed in extremely hot or cold environments, places exposed to
direct sunlight, or excessive dust or liquid.
--- It will cause overheating, malfunction or fire.
 Use the specified power supply according to POS models.
--- It will cause overheating or fire.
 Insert the power plug firmly into the end correctly.
--- If it is loosened, it will cause the electric shock, overheating or fire.
 Do not connect with devices which may cause electricity line noise.
--- It will cause malfunction.
 Do not touch the power plug with wet hands.
--- It will cause electric shock and malfunction.
 Do not touch or modify inside of the POS as the high voltage parts are mounted.
--- It will cause electric shock and malfunction.
 If you notice strange smell or smoke, turn off the main power switch immediately.
!

6
Remarks
Check the following before using POS
1) The required peripheral(s) has (have) been connected to the correct interface
connector(s);
2) The power plug is connected to AC outlet.
Attention for the handling of Touch Panel
The surface of touch panel is made from PET sheet with hard coat treatment. In order not to
damage the touch panel, please kindly note the following points:
1) Always press touch panel by a finger. Never use hard objects (hard and sharp objects
such as ball-point pen are even worse).
Note! If you use hard/sharp objects or hit strongly, the touch panel coating is removed
and Touch Panel will not recognize the correct position.
2) When cleaning
- Do not use hard cloth. Do not wipe hard.
- Use a) dry soft cloth, b) soft cloth with neutral detergent after wring dry or c) soft
cloth moistened with Ethanol, and wipe gently.
- Do not wipe Touch Panel hard even if the protection sheet is attached on it.
- Do not use sharp objects wrapped with cloth.
- Do not use thinner, benzene, volatile chemicals, acidic/alkaline solution. The
surface may be damaged.
3) When a foreign material is caught in the gap between Touch Panel and Cabinet
Please remove it, but do not use sharp objects such as ball-point pen, especially at the
edges.
Note! If a material is left caught, Touch Panel will consider that the position is always
pressed.

7
Interface Cover
Before you connect / disconnect the cable to the peripheral(s), make sure that the power is "OFF".
1) Pull the cover by pushing two hooks to remove the interface cover.
2) Insert 3 projections into the opening of the cabinet and two hooks likewise.
Close the cover by pushing the positions (not hooks) on the cover indicated by triangles
in the image below.
Bottom of LCD case

8
Cable Management (how to clamp the cables)
1) The clamper for cables is placed in the base. Pull up the LCD case by both hands to see
the clamper in the base.
2) In order to open the clamper, slide the clamper downward.
3) Run the cables through the clamper and close the clamper by pushing.
Clamper Close
Clamper Open

9
How to Clean the Cabinet and Touch Screen
When the cabinet and touch screen become dirty, please wipe them with a soft piece of cloth.
As for the touch screen, do not wipe it hard with a soft piece of cloth even if the protect sheet
is attached on it.
Notes! Do not use the sharp objects like skewer, ball-point pen to remove a dust at the
edges. They will damage the touch panel.
If the cabinet becomes very dirty, please wipe them using a soft piece of cloth which is
dipped in a neutral detergent with water and is tightly squeezed. Then, wipe them with a dry
soft piece of cloth one more time.
Notes! Do not use thinner, benzine or volatile chemicals for cleaning. The surface of
cabinets may be damaged.
In case of the power failure
The display after power recovery is different depending on the period of power failure.
Less than 5 minutes: It will be back to the screen when the power failure occurred.
More than 5 minutes: It will display Sign on screen.
In case if POS is locked down
IR
Forced shutdown and restart
Use this button only when POS locks (touch screen does not
work, etc). Press this button for 2 seconds and release it after you
hear buzzer sound. AX will shut down and restart automatically.
Use something sharp object such as a head of ball point pen to press IR button.
IR
Main Power
Switch

The crossed-out wheeled bin symbol is used
to show that this product must not be treated
as general household waste. Please contact
the supplier of this product to ensure that it is
disposed of correctly.
You will be helping to prevent potentially
negative consequences for the environment
and human health, which could otherwise be
caused by incorrect waste handling of the
product.