UNV OET-213H-BTS1 User manual

1
Digital Detection Module
Quick Guide
V1.00

2
1Packing List
No.
Name
Qty
Unit
1
Digital detection module
1
PCS
2
Screw kit
(two M3x6 countersunk head screws and two M3x6
pan head screws inside)
1
Set
3
Power adapter (purchased separately)
1
PCS
4
Bracket
1
PCS
5
Hint label
3
PCS
6
Special statement
1
PCS
7
User manual
1
PCS
2Product Overview
The digital detection module is a non-contact device for taking wrist temperatures.
It has a simple and elegant appearance and features a wide range, high precision,
low error, and long temperature measurement distance. It can connect to a face
recognition access control terminal through the RS485 interface. The module
supports temperature measurement and personnel information binding. It is
capable of rapidly identifying personnel information, taking the temperature, and
generating an alarm for people with abnormal temperature. In addition, it allows
setting a temperature threshold so as to strictly control the access permissions of
personnel (a person is not allowed to pass when the person's temperature exceeds
the threshold). The module is applicable to application scenes requiring strict
temperature measurement such as access control and attendance check.
1Environmental Conditions
Indoor use
Altitude: < 2000m
Environmental temperature: + 10 ℃~ + 45 ℃
Relative humidity: < 95% RH
Mains supply voltage fluctuations: ±10%

3
Overvoltage category (except cord/plug-connected equipment): Ⅱ
Pollution degree of the intended environment: the operational environment
should be with less dust to avoid the pollution of blackbody target. (Pollution
degree 2)
If the euipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.
2Appearance and size
The actual device appearance shall prevail. The figure below shows the device size.
3Structure and cable
The figure below shows the structure and cable of the device. The actual device shall
prevail.
1
2
Temperature sensor
4-pin cable

4
3Device Installation
3.1 Device Wiring
1Wiring Embedding
Before installing the digital detection module, plan the layout of the power cable.
For the diameter selection for the extension power cable, see the table below.
Diameter Selection for Extension Power Cables
The device is powered by DC 12V/2A and the lower limit of the operating
voltage is DC 9V (12V–25%).
Wire Diameter
(mm)
0.8mm
(20 AWG)
1mm
(18 AWG)
1.25mm
(16 AWG)
1.63mm
(14 AWG)
Transmission
Distance (m)
18
37
58
99
2Wiring description
The figure below shows the wiring between the digital detection module and
different devices. For the wiring terminal of each device, see the operation manual
of the device or consult manufacturers.
Digital
detection
module
Power
input
VDD12V Red
GND Black
+12V
GND
RS485
RS485_P Blue
RS485_N Brown
Face recognition access
control terminal/Face
recognition terminal

5
3.2 Tools Preparations
Antistatic wrist strap or antistatic gloves
Marker
Drill
M8/M6 simple open-end wrench
Phillips screwdriver
Slotted screwdriver
3.3 Installation Steps
NOTE!
Before installing the digital detection module, connect the cables between the
module and a face recognition access control terminal/face recognition terminal by
referring to section "Device Wiring" and sections related to the wiring in the quick
guide of the face recognition access control terminal/face recognition terminal.
1Wall mount
The figure below shows the process of installing the digital detection module on a
wall when the module is to be used in combination with a face recognition access
control terminal.
Installation mode 1
1. Mount the bracket to the wall.
2. Fix the temperature
measurement module.

6
Installation mode 2
NOTE!
This installation mode requires the EP-SZWB bracket, which needs to be purchased
separately.
2Standing pole mount
The figure below shows the process of installing the digital detection module on a
standing pole when the module is to be used in combination with a face recognition
access control terminal/face recognition terminal.
1. Fix the wall-
mounted bracket.
2. Fix the side-
mounted
bracket.
3. Fix the temperature
measurement module.

7
4Device Startup
1Device power-on
After the device is installed correctly, connect the power adapter (provided
separately) to the mains supply to start the device.
2Device configuration
Local configuration
When the digital detection module is used in combination with a face recognition
access control terminal, you can enable the temperature measurement function on
the Authentication Scene interface of the face recognition access control terminal.
Tap and hold the GUI for more than 3s. Enter the correct activation password to go
to the Activation Config interface.
Temperature value range: [30–45]

8
Configuration on the Web interface
You can also log in to the Web interface of the terminal and choose Setup >
Intelligent > Advanced Setting to enable the temperature measurement function.
3Device operations
When the temperature needs to be measured, aim the wrist at the temperature
measurement point, at a distance of 1–2.5cm.
Normal temperature Abnormal temperature

9
5Label Attaching
The packing list contains temperature measurement hint labels, which directly tell
users the temperature measurement point and distance. After installing the device,
attach the label to a proper position of the temperature measurement module.
No.
Label Attaching Description
1
This label is applicable when the temperature measurement module is
installed on a standing pole. For details, see "Standing pole mount".
2
This label is applicable when the temperature measurement
module is mounted on the wall and the temperature
measurement point is downward. For details, see installation
mode 1 in "Wall mount".
3
This label is applicable when the temperature measurement
module is mounted on the wall and the temperature
measurement point is outward. For details, see installation mode
2 in "Wall mount".
NOTE!
As shown in the figure above, the round film on the label aimed
at the temperature measurement point must be removed when
the label is attached.
(1)
(2)
(3)

10
6FAQs
Failure/Symptom
Solution
What should I do if
some people's
temperatures
cannot be taken?
1. Check whether the measurement distance is proper. The
recommended measurement distance is 1–2.5cm.
2. Check whether the wrist is aimed at the temperature
measurement point.
3. Check whether the wrist is covered. The wrist cannot be
covered by sleeves, watches, bracelets, or other objects.
A person must remove such objects, and then have the
temperature taken 0.5–1min later.
4. Check whether the body surface temperature is too low.
If a person comes from an outdoor low-temperature
environment to the measurement area, the person
needs to stay in this area for 5min before the
temperature is taken.
What should I do if
the temperature
measured by the
device is
inaccurate?
1. The device requires preheating after power-on. It enters
the optimal temperature measurement state 15 minutes
later.
2. Check whether the wrist is aimed at the temperature
measurement point.
3. Check whether the wrist is covered. The wrist cannot be
covered by sleeves, watches, bracelets, or other objects.
A person must remove such objects, and then have the
temperature taken 0.5–1min later.
4. Check whether the device is used in an environment with
low temperature, high temperature, or strong wind. If
yes, deploy the device in an indoor windless
environment with the temperature of 10°C to 45°C.

11
Failure/Symptom
Solution
What should I do
when a high
temperature alarm
is reported during
measurement?
1. Check whether a person has behaviors that affect the
body temperature, for example, getting out of a hot car,
doing strenuous exercise, or carrying hot drinks and hot
food. If yes, the person needs to stay in the
measurement area calmly and have the temperature
taken 5 minutes later.
2. Check whether the device is used in an overheated
environment. If yes, deploy the device in an indoor
windless environment with the temperature of 10°C to
45°C.
3. Use a medical-grade temperature measurement device
for a recheck.

12
Copyright Statement
No part of this manual may be copied, reproduced, translated or distributed in any form by any
means without prior content in writing from our company (referred to as us hereafter).
The product described in this manual may contain proprietary software owned by our company
and its possible licensors. Unless permitted, no one is allowed to copy, distribute, modify,
abstract, decompile, disassemble, decrypt, reverse engineer, rent, transfer, or sublicense the
software in any form by any means.
Export Compliance Statement
Our company complies with applicable export control laws and regulations worldwide, including
that of the People's Republic of China and the United States, and abides by relevant regulations
relating to the export, re-export and transfer of hardware, software and technology. Regarding
the product described in this manual, our company asks you to fully understand and strictly
abide by the applicable export laws and regulations worldwide.
Privacy Protection Reminder
Our company complies with appropriate privacy protection laws and is committed to protecting
user privacy. You may want to read our full privacy policy at our website and get to know the
ways we process your personal information. Please be aware, using the product described in
this manual may involve the collection of personal information such as face, fingerprint, license
plate number, email, phone number, GPS. Please abide by your local laws and regulations while
using the product.
About This Manual
This manual is intended for multiple product models, and the photos, illustrations,
descriptions, etc, in this manual may be different from the actual appearances, functions,
features, etc, of the product.
This manual is intended for multiple software versions, and the illustrations and descriptions
in this manual may be different from the actual GUI and functions of the software.
Despite our best efforts, technical or typographical errors may exist in this manual. Our
company cannot be held responsible for any such errors and reserves the right to change the
manual without prior notice.
Users are fully responsible for the damages and losses that arise due to improper operation.
Our company reserves the right to change any information in this manual without any prior
notice or indication. Due to such reasons as product version upgrade or regulatory
requirement of relevant regions, this manual will be periodically updated.
Disclaimer of Liability
To the extent allowed by applicable law, in no event will our company be liable for any special,
incidental, indirect, consequential damages, nor for any loss of profits, data, and documents.
The product described in this manual is provided on an "as is" basis. Unless required by
applicable law, this manual is only for informational purpose, and all statements, information,
and recommendations in this manual are presented without warranty of any kind, expressed
or implied, including, but not limited to, merchantability, satisfaction with quality, fitness for
a particular purpose, and noninfringement.

13
Users must assume total responsibility and all risks for connecting the product to the Internet,
including, but not limited to, network attack, hacking, and virus. We strongly recommends
that users take all necessary measures to enhance the protection of network, device, data
and personal information. Our company disclaims any liability related thereto but will readily
provide necessary security related support.
To the extent not prohibited by applicable law, in no event will our company and its
employees, licensors, subsidiary, affiliates be liable for results arising out of using or inability
to use the product or service, including, not limited to, loss of profits and any other
commercial damages or losses, loss of data, procurement of substitute goods or services;
property damage, personal injury, business interruption, loss of business information, or any
special, direct, indirect, incidental, consequential, pecuniary, coverage, exemplary,
subsidiary losses, however caused and on any theory of liability, whether in contract, strict
liability or tort (including negligence or otherwise) in any way out of the use of the product,
even if our company has been advised of the possibility of such damages (other than as may
be required by applicable law in cases involving personal injury, incidental or subsidiary
damage).
To the extent allowed by applicable law, in no event shall our total liability to you for all
damages for the product described in this manual (other than as may be required by
applicable law in cases involving personal injury) exceed the amount of money that you have
paid for the product.
Network Security
Please take all necessary measures to enhance network security for your device.
The following are necessary measures for the network security of your device:
Change default password and set strong password: You are strongly recommended to
change the default password after your first login and set a strong password of at least nine
characters including all three elements: digits, letters and special characters.
Keep firmware up to date: It is recommended that your device is always upgraded to the
latest version for the latest functions and better security. Visit our official website or contact
your local dealer for the latest firmware.
The following are recommendations for enhancing network security of your device:
Change password regularly: Change your device password on a regular basis and keep the
password safe. Make sure only the authorized user can log in to the device.
Enable HTTPS/SSL: Use SSL certificate to encrypt HTTP communications and ensure data
security.
Enable IP address filtering: Allow access only from the specified IP addresses.
Minimum port mapping: Configure your router or firewall to open a minimum set of ports
to the WAN and keep only the necessary port mappings. Never set the device as the DMZ
host or configure a full cone NAT.
Disable the automatic login and save password features: If multiple users have access to
your computer, it is recommended that you disable these features to prevent unauthorized
access.
Choose username and password discretely: Avoid using the username and password of your
social media, bank, email account, etc, as the username and password of your device, in case
your social media, bank and email account information is leaked.

14
Restrict user permissions: If more than one user needs access to your system, make sure
each user is granted only the necessary permissions.
Disable UPnP: When UPnP is enabled, the router will automatically map internal ports, and
the system will automatically forward port data, which results in the risks of data leakage.
Therefore, it is recommended to disable UPnP if HTTP and TCP port mapping have been
enabled manually on your router.
SNMP: Disable SNMP if you do not use it. If you do use it, then SNMPv3 is recommended.
Multicast: Multicast is intended to transmit video to multiple devices. If you do not use this
function, it is recommended you disable multicast on your network.
Check logs: Check your device logs regularly to detect unauthorized access or abnormal
operations.
Physical protection: Keep the device in a locked room or cabinet to prevent unauthorized
physical access.
Isolate video surveillance network: Isolating your video surveillance network with other
service networks helps prevent unauthorized access to devices in your security system from
other service networks.
Safety Warnings
The device must be installed, serviced and maintained by a trained professional with necessary
safety knowledge and skills. Before you start using the device, please read through this guide
carefully and make sure all applicable requirements are met to avoid danger and loss of property.
Storage, Transportation, and Use
Store or use the device in a proper environment that meets environmental requirements,
including and not limited to, temperature, humidity, dust, corrosive gases, electromagnetic
radiation, etc.
Make sure the device is securely installed or placed on a flat surface to prevent falling.
Unless otherwise specified, do not stack devices.
Ensure good ventilation in the operating environment. Do not cover the vents on the device.
Allow adequate space for ventilation.
Protect the device from liquid of any kind.
Make sure the power supply provides a stable voltage that meets the power requirements
of the device. Make sure the power supply's output power exceeds the total maximum
power of all the connected devices.
Verify that the device is properly installed before connecting it to power.
Do not remove the seal from the device body without consulting our company first. Do not
attempt to service the product yourself. Contact a trained professional for maintenance.
Always disconnect the device from power before attempting to move the device.
Take proper waterproof measures in accordance with requirements before using the device
outdoors.
Power Requirements
Installation and use of the device must be in strict accordance with your local electrical safety
regulations.
Use a UL certified power supply that meets LPS requirements if an adapter is used.
Use the recommended cordset (power cord) in accordance with the specified ratings.
Only use the power adapter supplied with your device.

15
Use a mains socket outlet with a protective earthing (grounding) connection.
Ground your device properly if the device is intended to be grounded.
Battery Use Caution
When battery is used, avoid:
High or low extreme temperatures during use, storage and transportation;
Extremely low air pressure, or low air pressure at high altitude.
Battery replacement.
Use the battery properly. Improper use of the battery such as the following may cause risks
of fire, explosion or leakage of flammable liquid or gas.
Replace battery with an incorrect type;
Dispose of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery;
Dispose the used battery according to your local regulations or the battery manufacturer's
instructions.
Avertissement de l’utilisation de la batterie
Lorsque utiliser la batterie, évitez:
Températures extrêmement élevées ou basses pendant l’utilisation, le stockage et le
transport;
Pression d’air extrêmement basse, ou pression d’air basse à haute altitude.
Remplacement de la batterie.
Utilisez la batterie correctement. Mauvaise utilisation de la batterie comme celles
mentionnées ici, peut entraîner des risques d’incendie, d’explosion ou de fuite liquide de gaz
inflammables.
Remplacer la batterie par un type incorrect;
Disposer d’une batterie dans le feu ou un four chaud, écraser mécaniquement ou couper
la batterie;
Disposer la batterie utilisée conformément à vos règlements locaux ou aux instructions du
fabricant de la batterie.
Regulatory Compliance
FCC Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
LVD/EMC Directive

16
This product complies with the European Low Voltage Directive 2014/35/EU
and EMC Directive 2014/30/EU.
WEEE Directive–2012/19/EU
The product this manual refers to is covered by the Waste Electrical &
Electronic Equipment (WEEE) Directive and must be disposed of in a
responsible manner.
Battery Directive-2013/56/EC
Battery in the product complies with the European Battery Directive
2013/56/EC. For proper recycling, return the battery to your supplier or to a
designated collection point.