Uplift Desk ACC094 User manual
2
Under no circumstances does the manufacturer accept warranty or liability claims for
damages caused from improper use of these panel brackets. Please provide these instructions
to any new user or owner of the panel brackets.
Step 1 - Bracket Alignment
Determine the approximate positions of the panel brackets for your panel size based on the information below.
CAUTION: Read all instructions before assembly. Failure to assemble or operate properly may result
in damage or personal injury. Retain manual for future reference.
Safety and Warnings
Acrylic Privacy Panel
(ships in separate package) Rubber Pad
qty 4 Panel Bracket A
qty 2 Panel Bracket B
qty 2
M5 x 12mm Machine Screw
qty 2 3mm Allen Wrench
Package Contents
Assembly Instructions
40” Acrylic Privacy Panel Bracket alignment: 52” Acrylic Privacy Panel Bracket alignment:
64” Acrylic Privacy Panel Bracket alignment: 72” Acrylic Privacy Panel Bracket alignment:
3
© UPLIFT Desk • 800-349-3839 • info@upliftdesk.com • upliftdesk.com
Step 2 - Rubber Pad Application
72” Acrylic Privacy Panels only, for other panels skip to Step 3.
A. Peel off the adhesive backing from one of the pads and apply it
to the one of brackets where shown: centered on the square face
of the bracket.
B. Repeat the previous step with the remaining three brackets.
Step 3 - Bracket Attachment
A. There are two types of Panel Brackets. Panel Bracket
A has a small post and a hole for the attachment
screw, and Panel Bracket B has a small post and a
larger post with a threaded hole for the attachment
screw.
B. When installing the Panel Brackets onto the Power
and Data Rail, be sure to place both of the A-type
brackets on one side of the rail and both of the
B-type brackets on the opposite side as shown.
Panel Bracket A Panel Bracket B
A
A
B
B
4
X✓
C. Place one Panel Bracket A and one Panel Bracket B on either side of the rail. Make sure the brackets are approximately
in the location on the Power and Data Rail shown in Step 1 based on the size of your privacy panel.
D. Bring the two brackets together around the Power and Data Rail so that the screw attachment holes are aligned, and
insert an M5 x 12mm Screw through the hole in Panel Bracket A and into the threads on Panel Bracket B. Using the
3mm Allen Wrench, turn the screw just enough to prevent the brackets from separating, but DO NOT fully tighten the
screw yet. It is important that there is a gap between the two brackets so that the privacy panel can be inserted in
the next step.
x
Leave a gap between the
two brackets.
Step 4 - Panel Installation
A. Orient the Acrylic Privacy Panel so that the holes are aligned in the same direction as the small posts on the Panel
Brackets. If the holes do not align within the bracket posts, ip the panel around.
E. Repeat the previous steps with the second pair of Panel Brackets.
X✓
5
© UPLIFT Desk • 800-349-3839 • info@upliftdesk.com • upliftdesk.com
B. Slide the panel between each set of Panel Brackets.
C. Starting with one set of Panel Brackets, position
the privacy panel so the small posts in the
brackets t into the holes in the panel.
D. Once the posts and holes are aligned, tighten the
M5 x 12mm Machine Screw with the 3mm Allen
Wrench.
E. Repeat for the second set of brackets.
F. If the nal assembly of the privacy panel is not
properly centered on the Power and Data Rail,
slightly loosen each of the screws and slide the
assembly left or right until centered. Then retighten
the screws.
6
Notes
SAVE THE INSTRUCTIONS
Study this manual carefully. If this product is sold, please provide this
manual to the buyer, installers, or support personnel operating the product.
Work Better. Live Healthier
AI-ACC094-1.0
Copyright Notice: This guide is a component of this UPLIFT Desk product. This guide is a part of
the scope of delivery, even if the item is resold. This guide is also available on the UPLIFT Desk
website: upliftdesk.com. These specications are subject to United States copyright law.
©
upliftdesk.com
800-349-3839
512-614-3152
Table of contents
Other Uplift Desk TV Mount manuals
