Register thermostat and/or system device
to a controller
NOTE!
At least one thermostat must be registered
before registering a system device.
To register room thermostats and system devices (interface
etc.) to the controller:
Enter registration mode
11. Press and hold the OK button on the controller, for
about 3 seconds, until the LED for channel 1 (or the
first unregistered channel) flashes red.
Register a thermostat
12. Select a thermostat channel.
12.1 Use buttons <or >to move the pointer (LED
flashes red) to a preferred channel.
12.2 Press the OK button to select the channel for
registration. The LED for the selected channel
starts flashing green.
12.3 Repeat steps 12.1 and 12.2 until all channels to
be registered with the thermostat are selected
(LEDs flashing green).
Note! It is recommended to register all channels
to the thermostat at the same time.
13. Select a thermostat.
THERMOSTAT T-143 AS A THERMOSTAT, WITH
VARIOUS FUNCTIONS
13.1 Gently press and hold the registration button
on the thermostat, release when the LED starts
flashing green (located in the hole above the
registration button).
The selected channel LED in the controller turns
fixed green and the registration is complete.
THERMOSTAT T-144
13.1 Using a pointed instrument, gently press and hold
the registration button on the thermostat, release
when the LED above the dial starts flashing.
The selected channel LED in the controller turns
fixed green and the registration is complete.
THERMOSTAT T-145
13.1 Gently press and hold the registration button
on the thermostat, release when the LED on the
front of the thermostat starts flashing.
The selected channel LED in the controller turns
fixed green and the registration is complete.
THERMOSTATS T-146, T-148 AND T-149
13.1 Press and hold both -and +buttons (T-149
= and ) on the thermostat until the text
CnF (configure) and a communication icon is
displayed.
The selected channel LED in the controller turns
fixed green and the registration is complete.
14. Repeat steps 12 and 13 until all available thermostats
are registered.
Register a system device
15. Make sure to be in registration mode (step 11).
15.1 Use buttons <or >to move the pointer to the
power LED (LED flashes red).
15.2 Press the OK button to enter system channel
registration mode. The power LED flashes
according to the pattern long blink, short pause,
long blink and channel 1 LED flashes red.
15.3 Select a system channel, see list below.
1 = Timer
2 = Not used
3 = Public thermostat with outdoor sensor
4 = Not used
5 = Public thermostat with Comfort/ECO switch
15.4 Press the OK button to select system device
channel. The channel LED starts flashing green
16. Select a system device matching the system channel.
TIMER I-143
16.1 Press and hold both -and +buttons on the
thermostat until the text CnF (configure) and a
communication icon is displayed.
The selected channel LED in the controller turns
fixed green and the registration is complete.
THERMOSTAT T-143 AS A SYSTEM DEVICE, WITH
VARIOUS FUNCTIONS
16.1 Gently press and hold the registration button
on the thermostat, release when the LED starts
flashing green (located in the hole above the
registration button).
The selected channel LED in the controller turns
fixed green and the registration is complete.
17. Repeat steps 15 and 16 until all available system devices
are registered.
Exit registration mode
18. Press and hold the OK button on the controller, for
about 3 seconds, until the green LEDs turn off to end
registration and return to run mode.
QUICK GUIDE
9
UPONOR SMATRIX BASE · QUICK GUIDE
UK
CZ
DE
DK
EE
ES
FI
FR
HR
HU
IT
LT
LV
NL
NO
PL
PT
RO
RU
SE
SI
SK
