urban ambiance UQL1090 User manual

Part Description Quantity
A Crossbar 1pc.
2 pcs.
2 pcs.
2 pcs.
B
C
D
E
F
Hex Nut
Lock Washer
Package Contents
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
A
B
C
D
E
Mounting Screw
1of5
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagrams
belowtobesureallpartsarepresent.Ifanypartsaremissingordamaged,donotattempttoassemble,install,or
operatethefixture.Contactcustomerserviceforreplacementparts.
Preparation:
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape,
safety glasses.
Light Source:
(1) Medium Base 100W Maximum
Estimated Assembly Time:
20-30 minutes
F
1pc.
2 pcs.
Lock Ball
Fixture Body
G
Shade 1pc.
G
Installation Instructions: UQL1090
www.urbanambiance.com

SKU: UQL1090
2of5
GND
2.4mm
13Ga
QUOIZEL R
7.5” 6.5” SQ.
8.5”
6.5”
5.5” Sq.
3” Dia.
1
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
REPLACEMENT PART DESCRIPTION QTY.
NO.
(1)100W Medium
Base Bulb
(Not Supplied)
UQL1090SH GLASS CLEAR HAMMERED 1
1

3of5
STEP 2 -Attach Crossbar to Outlet Box
A. Attach the Crossbar (A) to Outlet Box and secure by
threading Outlet Box Screws (not supplied) into the
Mounting Holes on the Outlet Box. Tighten until snug.
Crossbar
Outlet
Box
Outlet Box
Screw
Mounting
Hole
Figure 2
Figure 1
Crossbar
Mounting
Screw Lock Washer
Hex Nut
Backplate
STEP 1 -Attach Mounting Screws, Lock
Washers and Hex Nuts to Crossbar
A. Line up a set of holes on the Crossbar (A) and Holes on
the Backplate of the Fixture Body (F).
B. Thread Mounting Screws (B) into the holes on the
Crossbar (A), pass Lock Washers (C) and thread Hex
Nut (D) onto the Mounting Screws (B). Hand tighten
until snug.
Fixture
Body
Installation Instructions: UQL1090
www.urbanambiance.com

4of5
STEP 3 Make Wire Connections-
A. Use standard wire connectors to make all wire
connections. (Connectors are not included with fixture.)
Strip and prepare wire ends according to instructions
supplied with connectors.
B. Connect White Supply Wire from the Outlet Box to White
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box
to Black Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground
Wire from fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
Figure 4
White wire from supply White wire from fixture
Black wire from supply
(or Red)
Black wire from fixture
Ground wire from supply Ground wire from fixture
Figure 5
Figure 3
Mounting
Screw
Lock Ball
Backplate
Fixture Body
STEP 4 -Attach Fixture Body to Mounting
Screw
A. Place the Backplate of the Fixture Body (F) over the
Mounting Screws (B). Place caulk (not supplied) into
threads of Mounting Balls (E) and thread them onto the
Mounting Screws (B). Hand tighten until snug.
Installation Instructions: UQL1090
www.urbanambiance.com

5of5
Figure 7
Bulb
Socket
STEP 5 -Install Bulb
A. This fixture uses standard bulb with a medium screw base.
Maximum 100 watts.
B. Insert bulb and screw snugly into place.
STEP 6 -Attach Shade to Socket
A. Place the Slot on the Shade (G) line up the Screw Head
on Shade Holder and then rotate the Shade (G). Do not
free your hands until the Shade is seated onto the
Shade Holder.
Shade
Shade Holder
Figure 6
Slot
Screw Head
STEP 7 Apply Silicone Sealer-
A. Make sure exterior wall surface and fixture backplate
are free of dirt before applying caulk. Using exterior
grade caulk, caulk over top of backplate and down
other side. Do not caulk bottom of fixture backplate to
ensure proper moisture drainage.
Your fixture is now assembled and ready to use.
Enjoy!
Exterior
Grade Caulk
Outdoor
Fixture
Backplate
Exterior Wall Surface
Figure 8
Installation Instructions: UQL1090
www.urbanambiance.com