urban ambiance UQL1153 User manual

Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
1of5
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape,
safety glasses.
Light Source: (3) Candelabra Base Bulbs 40W Maximum
Estimated Assembly Time: 20-30 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams
below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or
operate the fixture. Contact customer service for replacement parts.
Part Description Quantity
A Crossbar
Mounting Screw
1pc.
1pc.
1pc.
1pc.
1pc.
B
C
D
E
Stem
Package Contents
Finial
Socket Assembly
A
B
C
D
F
E
1pc.
F
Cage
Installation Instructions: UQL1153
www.urbanambiance.com

1
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION REQ.
NO.
2of5
(3) 40W Candelabra
Base Bulbs
(Not Supplied)
15.5”
8”
SKU: UQL1153

3of5
STEP 1 Install Crossbar-
A. Attach the Crossbar (A) to the Outlet Box with the
Outlet Box Screws (not supplied). Hand tighten until
snug.
Figure 1
STEP 2 Install Mounting Screw-
A. Screw the Mounting Screws (B) into the mounting holes
on the Crossbar (A), which aligns to the Keyholes on
the Ceiling Canopy. Leave proper length of the
Mounting Screws to mount the Ceiling Canopy. To
achieve this length, you need attach the Ceiling Canopy
over the Mounting Screws and adjust the Mounting
Screws accordingly.
Figure 2
Outlet Box
Crossbar
Outlet Box
Screw
Mounting Screw
Crossbar
Ceiling Canopy
Keyhole
Installation Instructions: UQL1153
www.urbanambiance.com

4of5
STEP 3 Make Wire Connections-
A. Use standard wire connectors to make all wire
connections. (Connectors are not included with fixture.)
Strip and prepare wire ends according to instructions
supplied with connectors.
B. Connect White Supply Wire from the Outlet Box to White
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box
to Black Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground
Wire from fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
Figure 4
White wire from supply White wire from fixture
Black wire from supply
(or Red)
Black wire from fixture
Ground wire from supply Ground wire from fixture
Figure 3
STEP 4 -Attach Ceiling Canopy to Mounting
Screw
A. Place the Keyholes on the Ceiling Canopy over the
Mounting Screws (B) and then rotate the Ceiling
Canopy until it is secure to the Mounting Screws (B).
Figure 5
Ceiling
Canopy
Keyhole
Mounting
Screw
Installation Instructions: UQL1153
www.urbanambiance.com

5of5
STEP 5 Install Bulb-
A. This fixture uses candelabra bulb with a candelabra
screw base. Maximum 40 watts.
B. Insert bulb and screw properly into place.
Figure 6
Socket
Bulb
STEP 6 Install Cage-
A. Screw the beaded end of the Stem (D) into the Coupling
on the bottom center of the Socket Assembly (C). Hand
tighten until snug.
B. Pass the Cage (E) over the end of the Stem (D) and
secure with the Finial (F). Hand tighten until snug.
Your fixture is now assembled and ready to use. Enjoy! Socket
Assembly
Coupling
Figure 7
Stem
Cage
Finial
Installation Instructions: UQL1153
www.urbanambiance.com