urban ambiance UQL1174 User manual

Part Description Quantity
A
1 pc.
1 pc.
3 pcs.
Finial
B
C
Package Contents
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
A
B
C
Mounting Screw
1of5
Waterproof Washer
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire
strippers, electrical tape, safety glasses.
Estimated Assembly Time: 20-30 minutes
Bulb Recommended: (3) Candelabra Base 60W Maximum
Preparation: Identify and inspect all parts before beginning installation. Check package
content list and diagrams below to be sure all parts are present. If any parts are missing
or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer
service for replacement parts.
D
E
F
D
1 pc.
1 pc.
1 pc.
Fixture Hood
E
F
Center Stem
Cage
Installation
Instructions:
UQL1174
www.urbanambiance.com

SKU: UQL1174
1
PART NUMBER
UQL1174CC
(3)60W candelabra
base bulbs
(not Supplied) NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
CANDLE COVER 2"H
REQ.
3
NO.
2of5
9”
23”
1

Figure 1
Bulb
Figure 2
3of5
Center Stem
Coupling
STEP 1 Install Center Stem-
A. Thread the beaded end of the Center Stem (D) into the
Coupling in the center of the Cage (F). Hand tighten
until snug.
STEP 2 -Install Bulb
A. standard bulb with a candelabra screw
base 0
This fixture uses
. Maximum 6 watts.
B. Insert bulb and screw snugly into place. Socket
Finial
Figure 3
STEP 3 -Install Fixture Hood
A. Place the Fixture Hood (E) and the Waterproof Washer
(C) over the top end of the Center Stem (D). Secure by
threading the Finial (B) onto the Center Stem (D). Hand
tighten until snug.
Fixture
Hood
Waterproof
Washer
Center Stem
Cage
Installation Instructions: UQL1174
www.urbanambiance.com

4of5
STEP 4 Drill Pilot Holes on Post-
A. Carefully fit the Post Fitter over the end of the Post (not
supplied), making sure the Post Fitter is fully seated.
B. Mark the drill point for the (3) Mounting Screws, using
(3) Mounting Holes as reference. After marking hole
locations, remove fixture from post and drill 1/16” pilot
holes for screws.
Post Figure 4
Post Fitter
Figure 5
STEP 5 Make Wire Connections-
A. Use standard wire connectors to make all wire
connections. (Connectors are not included with fixture.)
Strip and prepare wire ends according to instructions
supplied with connectors.
B. Connect White Supply Wire from the Post to White Wire
from fixture.
C. Connect Black (or Red) Supply Wire from the Post to
Black Wire from fixture.
D. Connect Ground Wire from the Post to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Post.
Figure 6
White wire from supply White wire from fixture
Black wire from supply
(or Red)
Black wire from fixture
Ground wire from supply Ground wire from fixture
Post
Installation Instructions: UQL1174
www.urbanambiance.com

5of5
STEP 6 -Attach Fixture Body to Post
A. Coat the top 1” of the Post with Clear Silicone Caulk
(not supplied) and position the Post Fitter onto the Post.
Be sure to seat it completely, aligning the holes in the
Fitter with the 1/16” Pilot Holes drilled into the Post.
B. Secure the Fixture to Post with (3) Mounting Screws.
Your fixture is now assembled and ready to use. Enjoy!
Mounting Screw
Post Figure 7
Post Fitter
Mounting
Hole
Installation Instructions: UQL1174
www.urbanambiance.com