urban ambiance UQL1255 User manual

1of2
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: LED 16W
Estimated Assembly Time: 20-30 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Fixture Body
x1 B
STEP 1 Drill Pilot Holes on Post-
A. Carefully fit the Post Fitter over the
end of the Post (not supplied),
making sure the Post Fitter is fully
seated.
B. Mark the drill point for the (3)
Mounting Screws, using (3)
Mounting Holes as reference. After
marking hole locations, remove
fixture from post and drill 1/16” pilot
holes for screws.
Post
Post Fitter
Figure 1
Mounting Hole
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 2
A
Mounting
Screw
x3
STEP 3 -Attach Fixture Body to Post
A. Coat the top 1” of the Post with Clear Silicone Caulk (not supplied)
and position the Post Fitter onto the Post. Be sure to seat it
Post
Post Fitter
Figure 3
Mounting Hole
HOW TO REPLACE GLASS PANELS
Allen Screw
Screw
Fixture
Hood
Glass
Holder
Glass
Panel
Cage
A.
Fixture Hood and
remove the Fixture
Hood from the Cage.
B. Separate Quick
Connector and then
unscrew Screws from
the Cage and remove
LED Module and Heat
Sink, the Glass Holder.
Replace Glass Panels
from the Cage and then
re-install the Glass
Holder, LED Module
and Heat Sink. Secure
with removed Lock
Screws.
C. Connect Quick
Connectors. Attach the
Fixture Hood back onto
the Cage and secure
with Allen Screws.
Unlock Allen Screws on
the
Figure 4
(Step 3 Continued)
completely, aligning the holes in
the Fitter with the 1/16” Pilot Holes
drilled into the Post.
B. Secure the Fixture to Post with (3)
Mounting Screws (A).
Your fixture is now assembled
and ready to use. Enjoy!
LED Module
and Heat Sink
Male Quick
Connector Female Quick
Connector
Installation Instructions: UQL1255
www.urbanambiance.com

2of2
PART NUMBER
1
NO. PART NUMBER REPLACEMENT PART REQ.
UQL1255PA 4
GLASS PANEL
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
SKU: UQL1255
16”
9.5” SQ.
1
HOW TO REPLACE LED MODULE
A. Fixture Hood. Remove the Fixture Hood
from Cage.
B. Separate Quick Connector and then unscrew Screws from the Cage
and remove LED Module and Heat Sink.
C. Unscrew Lock Screws on the LED Module. Replace the LED Module
with the replacement. Pass Lock Screws through the replacement
Unlock Allen Screws on the
Allen Screw
Fixture
Hood
Screw
LED Module
Cage with
Glass
Panels
Lock Screw
Heat Sink
Figure 5
Hex Nut
Female
Quick
Connector
Male Quick
Connector
LED Module, the Heat
Sinks as shown and
thread Hex Nuts onto
Lock Screws to secure
them together. Hand
tighten until snug.
D. Pass the Quick
Connector from the LED
Module through the hole
on the Heat Sink.
E. Re-install LED Module
and Heat Sink onto the
top edge of the Cage.
Secure with Screws.
Connect Quick
Connectors. Attach
Cage with Glass Panels
back onto the Fixture
Hood and secure with
Allen Screws.
Upper
Heat Sink
www.urbanambiance.com