urban ambiance UQL1120 User manual

Part Description Quantity
A Crossbar 1pc.
2 pcs.
2 pcs.
2 pcs.
B
C
D
E
F
Hex Nut
Lock Washer
Package Contents
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
A
B
C
D
E
Mounting Screw
1of6
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape,
safety glasses.
Light Source: (1) Medium Base Decorative Filament 60W bulb (provided), Maximum 100W,Alternate bulb (1) 23W
CFLMaximum.
Estimated Assembly Time: 20-30 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams
below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or
operate the fixture. Contact customer service for replacement parts.
F
1pc.
2 pcs.
2 pcs.
Mounting Ball
Alternate Mounting screw
Fixture Body
G
H
I
1pc.
1pc.
G
H
I
J
Shade
Bulb
1pc.
Cage
K
Washer
J
K2 pcs.
L
L2 pcs.
Lock Knob
Installation Instructions: UQL1120
www.urbanambiance.com

SKU: UQL1120
1
2
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION REQ.
NO.
2of6
GND
2.4mm
13Ga
QUOIZEL R
(1)Medium Base
Decorative
Filament 60W
bulbs (provided),
Maximum 100W.
6.5”
11.5”
7.5”
4” Dia.
6” Dia.
UQL1120SH
UQL1120BU
GLASS CLEAR SEEDY 4" D
REPRODC 60W 1910 INCANDESCENT BULB
1
1
1
2
Rev.C

3of6
STEP 2 -Attach Crossbar to Outlet Box
A. Attach the Crossbar (A) to Outlet Box and secure by
threading Outlet Box Screws (not supplied) into the
Mounting Holes on the Outlet Box. Tighten until snug.
Crossbar
Outlet
Box
Outlet Box
Screw
Mounting
Hole
Figure 2
Figure 1
Crossbar
Lock Washer
Hex Nut
Backplate
STEP 1 -Attach Mounting Screws,
Lock Washers and Hex Nuts
to Crossbar
A. Line up a set of holes on the Crossbar (A) and
Holes on the Backplate of the Fixture Body
(G).
B. Thread Mounting Screws (B) or Alternate
Shorter Mounting Screws (F) into the holes on
the Crossbar (A), pass Lock Washers (C) and
thread Hex Nut (D) onto the Mounting Screws
(B) .
Hand tighten until snug.
or Alternate Shorter Mounting Screws (F)
Note: Use the Alternate Shorter Mounting
Screw (F) if your installation requires a shorter
mounting screw.
Fixture
Body
Mounting Screw
or Alternate Short
Mounting Screw
www.urbanambiance.com
Installation Instructions: UQL1120

4of6
STEP 3 Make Wire Connections-
A. Use standard wire connectors to make all wire
connections. (Connectors are not included with fixture.)
Strip and prepare wire ends according to instructions
supplied with connectors.
B. Connect White Supply Wire from the Outlet Box to White
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box
to Black Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground
Wire from fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
Figure 4
White wire from supply White wire from fixture
Black wire from supply
(or Red)
Black wire from fixture
Ground wire from supply Ground wire from fixture
Figure 5
Figure 3
STEP 4 -Attach Fixture Body to
Mounting Screw
A. Place the Backplate of the Fixture Body (G) over
the Mounting Screws (B) or the Alternate Short
Mounting Screws (F) and secure with Mounting
Balls (E). Hand tighten until snug.
Mounting Ball
Backplate
Fixture Body
Mounting Screw
or Alternate Short
Mounting Screw
www.urbanambiance.com
Installation Instructions: UQL1120

5of6
STEP 5 Install Bulb-
A. This fixture uses Medium Base Decorative Filament
60W bulb (H), Maximum 100W. Insert bulb and screw
snugly into place.
Figure 6
Bulb
Socket
STEP 6 -Attach Shade to Fixture Body
A. Thread Shade (I) to Fixture Body (G), hand tighten until
snug.
Shade
Fixture Body
Figure 7
www.urbanambiance.com
Installation Instructions: UQL1120

6of6
STEP 7 Attach Cage to Fixture Body-
A. Pass the Bolt on the top of Cage (J) though the Hole on
the Fixture Body (G). Place the Washer (K) over the
Bolt, secure by thread the Lock Knobs (L) onto the Bolt
on the top of Cage (J). Hand tighten until snug. Please
make sure the gap on the Cage and the Bolt in the hood
in a line.
Figure 8
STEP 8 Apply Silicone Sealer to Backplate-
A. Make sure exterior wall surface and fixture backplate
are free of dirt before applying caulk. Using exterior
grade caulk, start on one side of fixture backplate and
follow contour, where the fixture backplate meets the
exterior wall surface upward. Proceed to caulk over top
of backplate and down other side. Do not caulk bottom
of fixture backplate to ensure proper moisture
drainage.
Your fixture is now assembled and ready to use.
Enjoy!
Exterior
Grade Caulk
Outdoor Fixture
Backplate
Exterior Wall Surface
Figure 9
Mounting
Ball
Cage
Fixture Body
Lock Knob
Hole
Bolt
Washer
Bolt
Gap
www.urbanambiance.com
Installation Instructions: UQL1120