urban ambiance UQL1263 Mounting instructions

1of2
Package Contents
ACrossbar Assembly
x1
Fixture Body
x1
C
B
Alternate
Mounting screw
x2
F
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1)A21 Medium Base Bulb 150W Maximum or
(1) Medium Base Vintage Bulb is recommended but not supplied.
Estimated Assembly Time: 30-45 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Figure 2
(Step 2 Continued)
and secure with mounting balls. Note: The backplate and Fixture
Body (C) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screws
or alternate short mounting screws on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws or alternate short mounting screws in
or out of the crossbar until the correct length is achieved. Once the
backplate and Fixture Body (C) is secure, remove the mounting ball
and Fixture Body (C) and proceed to Step 3.
Hex Nut and
Lock Washer
C
Mounting Ball
A
Mounting Screw
or Alternate Short
Mounting Screw
Backplate
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Glass Holder
x1
D
Lock Ball
x2
Glass
Shade
x1
E
STEP 1 Install Crossbar Assembly-
.
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
Figure 1
A
Mounting Screw
or Alternate Short
Mounting Screw
STEP 2 -Test Fit the Backplate to the Crossbar Assembly
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (C) onto the Crossbar Assembly (A)
Assembly Instruction Sheet: UQL1263

2of2
STEP 4 Install the Fixture Body-
A. Position the backplate and Fixture Body (C) onto the Crossbar
Assembly (A). Place the holes in the backplate over the mounting
screws or alternate short mounting screws. Secure the backplate
and Fixture Body (C) by using the mounting balls and hand tighten
the mounting balls until snug.
Figure 4
STEP 5 -Install Bulb and Glass
Shade
A. Insert the bulb onto the socket
and screw snugly into place.
B. Place the Glass Shade (F) over
the bulb carefully. Attach the
shade neck to the fixed shade
holder on the Fixture Body (C).
With one hand holding the Glass
Shade (F), place the Glass
Holder (D) to other side of shade
Figure 5
F
E
D
Fixed Shade
Holder
Neck
Bolt
F
C
neck and place it over
bolts on the fixed glass
holder. Secure them
together by threading
Lock Balls (E) onto
bolts. Hand tighten until
snug.
Figure 6
Exterior
Grade Caulk
Backplate
Exterior
Grade Caulk
STEP 6 -Apply Silicone Sealer
A. Make sure the exterior wall surface and fixture backplate are free of
dirt before applying caulk. Using exterior grade caulk, caulk over
top of backplate and down both sides. Do not caulk the bottom of
the fixture backplate to ensure proper moisture drainage.
Your fixture is now assembled and ready to use. Enjoy!
LLE8411WT
FINISH: WESTERN BRONZE
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
7”
9.25” Dia.
11”
13.5”
12”
8”
19.5”
Fixture can
only be
mounted in
the direction
indicated
C
Mounting Ball
A
Mounting Screw
or Alternate Short
Mounting Screw
Backplate