urban ambiance UQL1130 User manual

Package Contents
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1)A19 Medium Base 100W Maximum,Alternate bulb (1) 23W CFL
Estimated Assembly Time: 20-30 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
1of2
ACrossbar Assembly
x1
White wire
from supply White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture Figure 3
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
Figure 1
STEP 1 Install Crossbar Assembly-
.
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Supply Wires with
Ground Wire
A
Outlet Box Screws
(not included)
Outlet Box
ELock Ball
x4
GND
R
Q
U
O
Z
E
L
BFixture Body
x1
DOuter Shade
x1
CInner Shade
x1
STEP 2 Fit Backplate to
Crossbar Assembly
-
A.
on Fixture Body (B) to
the
Remove mounting balls from the
Crossbar Assembly (A). Fit the
backplate
Crossbar Assembly (A) and
secure with mounting balls.
Note: The backplate
should be snug against
the wall and the mounting balls.
If
on Fixture
Body (B)
not, adjust the length of the
nipple on the Crossbar
Figure 2
Mounting Screw B
Mounting Ball
ABackplate
Hex Nut and
Lock Washer
Assembly (A) by unscrewing the preassembled hex nut and lock
washer and then screwing the mounting screws in or out of the
crossbar until the correct length is achieved. Once the backplate on
Fixture Body (B) is secure, remove the mounting ball and Fixture
Body (B) and proceed to Step 3.
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
Mounting Screw B
Mounting Ball
ABackplate
Figure 4
STEP 4 Install Fixture Body-
A. Carefully tuck all wires into the
outlet box and position the
backplate of fixture body (B) over
the outlet box. Align the holes in
the backplate with the mounting
screws. Place caulk (not
supplied) into the previously
removed mounting balls and then
attach fixture body (B) using the
mounting balls. Hand tighten
until snug.
B
Figure 5
STEP 5 Install Bulbs and Shades-
A. This fixture uses standard bulb with
medium screw base. Maximum 100
watts. Insert bulb and screw snugly
into place.
Your fixture is now assembled and
ready to use. Enjoy!
B. Place the Inner Shade (C) to the
Outer Shade (D). Life the Outer
Shade (D) with the Inner Shade (C)
upward and pass the holes on the
Outer Shade (D) through the bolts
on the Fixture Body (B). Secure by
threading Lock Balls (E) onto the
Bolts. Hand tighten until snug.
Bulb (not
included)
Socket
C
D
E
Bolt
Installation Instructions: UQL1130
www.urbanambiance.com

2of2
SKU: UQL1130
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
10.75”9.5” Dia.
5.25” Dia.
9.75”
GND
R
Q
U
O
Z
E
L
(1) 100W
Bulb
(Not Supplied)
Medium
Base PART NUMBER
1
NO. PART NUMBER REPLACEMENT PART REQ.
UQL1130SHGLASS 1
1
www.urbanambiance.com