urban ambiance Cambridge UQL1144 User manual

Part Description Quantity
A Crossbar 1pc.
1pc.
2 pcs.
2 pcs.
2 pcs.
2 pcs.
Fixture Body
B
C
D
E
F
Hex Nut
Lock Washer
Package Contents
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
Mounting Ball
Mounting Screw
1of5
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety
glasses.
Light Source:
(2) Candelabra Base 60W Maximum
Estimated Assembly Time:
20-30 minutes
Preparation:
Identify and inspect all parts before beginning installation. Check package content list and diagrams
below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or
operate the fixture. Contact customer service for replacement parts.
A
B
C
D
E
F
G
2 pcs.
GAlternate Mounting Screw
Installation Instructions: UQL1144
www.urbanambiance.com

SKU: UQL1144
1
2
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
REPLACEMENT PART DESCRIPTION QTY.
NO.
3
2of5
UQL1144BA
UQL1144CC
MOUNTING BALL
CANDLE COVER
2
2
2
20”
13”
10”
9”
(2) 60W Candelabra
base bulbs
(not Supplied)
UQL1144KIT MOUNTING HARDWARE 1
3
1

3of5
STEP 2 -Attach Crossbar to Outlet Box
A. Attach the Crossbar (A) to Outlet Box and secure by
threading Outlet Box Screws (not supplied) into the
Mounting Holes on the Outlet Box. Tighten until snug.
Figure 2
STEP 1 -Attach Mounting Screws, Lock
Washers and Hex Nuts to
Crossbar
A. Line up a set of holes on the Crossbar (A) and
Holes on the backplate of the Fixture Body (F).
B. Thread Mounting Screws (B) or Alternate Shorter
Mounting Screws (G) into the holes on the
Crossbar (A), pass Lock Washers (C) and thread
Hex Nut (D) onto the Mounting Screws (B) or
Alternate Shorter Mounting Screws (G). Hand
tighten until snug.
Fixture
Body
Crossbar
Lock Washer
Hex Nut
Crossbar
Outlet Box Outlet Box
Screw
Mounting Hole
Figure 1
Mounting Screw
or Alternate Short
Mounting Screw
Installation Instructions: UQL1144
www.urbanambiance.com

4of5
Figure 5
Mounting Ball
Backplate
Figure 3
STEP 3 Make Wire Connections-
A. Use standard wire connectors (not included) to make all
wire connections. Twist connectors until wires are tightly
joined together. Wrap each connection with approved
electrical tape and carefully stuff all the connected wires
into the Outlet Box.
Figure 4
White wire
from supply White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Mounting Screw
or Alternate Short
Mounting Screw
STEP 4 -Attach Fixture Body to Mounting
Screw
A. Place the backplate of the Fixture Body (F) over the
Mounting Screws (B) or Alternate Shorter Mounting
Screws (G) and secure with Mounting Balls (E). Hand
tighten until snug.
Installation Instructions: UQL1144
www.urbanambiance.com

5of5
STEP 6 Apply Silicone Sealer to Mounting
Balls
-
A. To prevent moisture from entering the wire
compartment, apply a small amount of silicone sealer
(not included) to the threaded side of the mounting
balls (E) and then install them onto the mounting
screws (B). Wipe off excess caulk.
STEP 7 Apply Silicone Sealer to Backplate-
A. Make sure exterior wall surface and fixture backplate
are free of dirt before applying caulk. Using exterior
grade caulk, start on one side of fixture backplate and
follow contour, where the fixture backplate meets the
exterior wall surface upward. Proceed to caulk over top
of backplate and down other side. Do not caulk bottom
of fixture backplate to ensure proper moisture
drainage.
Your fixture is now assembled and ready to use.
Enjoy!
STEP 5 -Install Bulb
A. This fixture uses standard bulb with a candelabra screw
base. Maximum 60 watts.
B. Place the bulb from the bottom of the glass frame. Insert
bulb and screw snugly into place.
Figure 6
Figure 7
Mounting Ball
Exterior
Grade Caulk
Outdoor Fixture
Backplate
Exterior Wall Surface
Figure 8
Socket
Bulb
Installation Instructions: UQL1144
www.urbanambiance.com