urmet domus 1083/12 User manual

Configuration guide
System Type B
1083/12 -1083/15 -1083/16

Contents
Introduction
Menu structure
Configuration
Programming proximity access keys
Programming door open codes
Appendix
Contents
Introduction
Menu structure
Configuration
Programming proximity access keys
Programming door open codes
Appendix
Contents
Introduction
Menu structure
Configuration
procedure
Programming proximity access keys
Programming door open codes
Appendix
procedure
Programming proximity access keys
Programming door open codes
procedure
Programming proximity access keys
Programming door open codes
Programming proximity access keys
Page 1
Page
Page 4
Page 1
Page 1
Page
Page 1
Page
3
Page 4
Page 1
4
Page 1
5
Page
16

Introduction
1083/201083/20 1083/75
This programming guide is intended specifically for a particular type of system –System Type B
Page 1
System Type B–
One (or up to a maximum of four) ‘Main’ entry panels i.e.
panels which call all apartments in the system.
The apartment numbers are not in the range of 1 to 127.
Example 1 -A block of fifty apartments with postal
addresses from 201 to 250
Example 2 -A block of twenty apartments with postal
addresses from 451 to 470.

200
200
200
200
Page 2
In
System Type
an
OFFSET
The reason is that using
switches 2
largest number that can be made is 127.
So for example the DIP switch setting in
apartment 200 could be
The system needs to ‘know’ that when a
visitor dials 200 the monitor or
with address
be called.
In this case the
Page 2
ADDRESS
System Type
OFFSET
in the numbering sequence.
The reason is that using
switches 2
-
8 (switch 1 is not used) the
largest number that can be made is 127.
So for example the DIP switch setting in
apartment 200 could be
The system needs to ‘know’ that when a
visitor dials 200 the monitor or
with address
be called.
In this case the
ADDRESS
System Type
B
it is necessary to create
in the numbering sequence.
The reason is that using
8 (switch 1 is not used) the
largest number that can be made is 127.
So for example the DIP switch setting in
apartment 200 could be
The system needs to ‘know’ that when a
visitor dials 200 the monitor or
with address
0
(postal address 200)
In this case the
OFFSET
ADDRESS
0
it is necessary to create
in the numbering sequence.
The reason is that using
monitor
8 (switch 1 is not used) the
largest number that can be made is 127.
So for example the DIP switch setting in
apartment 200 could be
0
The system needs to ‘know’ that when a
visitor dials 200 the monitor or
(postal address 200)
OFFSET
would be 200.
it is necessary to create
in the numbering sequence.
monitor
8 (switch 1 is not used) the
largest number that can be made is 127.
So for example the DIP switch setting in
0
.
The system needs to ‘know’ that when a
visitor dials 200 the monitor or
handset
(postal address 200)
would be 200.
it is necessary to create
in the numbering sequence.
monitor
DIP
8 (switch 1 is not used) the
largest number that can be made is 127.
So for example the DIP switch setting in
The system needs to ‘know’ that when a
handset
(postal address 200)
must
would be 200.
it is necessary to create
in the numbering sequence.
8 (switch 1 is not used) the
largest number that can be made is 127.
So for example the DIP switch setting in
The system needs to ‘know’ that when a
handset
must

Menu Structure
LANGUAGE
CONFIGURATION
NAMES
DOOR OPENER
KEYS
RESET
SIMPLIFIED GUI
MODULE TYPE
MULTIRISE
ID PRIMARY MODULE
CODE TYPE
BUSY TIME
STOPABLE
DOOR LOCK 1 RELEASE TIME
DOOR LOCK 1
DOOR LOCK 2 RELEASE TIME
DOOR LOCK 2
PASSWORD
LCD BACKLIGHT
BUTTON SOUND
MULTITOUCH CALL
WELCOME MESSAGE
TIME ZONE
DATE AND TIME
DAY
POSTMAN
VOCAL SYNTHESIS
SWITCHBOARD
NEW
MODIFY
DELETE
DELETE ALL
NEW
MODIFY
DELETE
DELETE ALL
NEW
MODIFY
DELETE
Page 3

Configuration procedure
When the unit is first powered the screen is as follows –
On the entry panel keypad press 99999 and you will see this screen –
Enter 1000 (the default password) then press
Use the and buttons to select
LINGUA and press
Use the and buttons to select
ENGLISH UK and press
ENGLISH UK
Page 4

You see this screen –
Press the button to select CONFIGURATION then press
Use the or buttons to select YES and press
PRIMARY
SECONDARY
Use the or buttons to select PRIMARY and press
Page 5
FROM: 0
TO: 0
Press
LANGUAGE

CONFIGURATION

In a system with only one entry panel the ID is always 0. In this case just press .
In a system with two, three or four panels, each must have a different ID.
For example to change the panel ID to 1just press then press
It is suggested to keep the default setting by pressing
It is suggested to keep the default setting by pressing
DOOR LOCK 1 RELEASE TIME adjusts the voltage free relay (C NO NC) time
and also the solid state lock release output (SE+ SE-) time.
For example for a time of 10 seconds press 1 0
Page 6
The ID of the panel is determined by where it is connected in the system.
You must refer to the connection diagram of your system for the ID of each panel.

Choosing FREE means that the door can be opened by the monitor or handset at
any time without the monitor or handset being called.
Choosing SECRET means that the monitor or handset must be called before it can
open the door.
Use the or buttons to make a selection then press
DOOR LOCK 2 RELEASE TIME adjusts the voltage free relay (C NO) time.
For example for a time of 1 second press 1then press
Choosing FREE means that the gate can be opened by the monitor or handset at
any time without the monitor or handset being called.
Choosing SECRET means that the monitor or handset must be called before it can
open the gate.
Use the or buttons to make a selection then press
For an explanation of the three different lock outputs see the appendix
Page 1
4
Page 7

Change the PASSWORD if required by pressing the button below Cto delete
the current password -
Enter the new password and press
Adjusts the panel display backlight
Use the or buttons to make a selection then press
The entry panel button confirmation beep can be ON or OFF.
Use the or buttons to make a selection then press
It is possible that when a number of buttons are pressed at the same time, a
particular monitor or handset can be called, for example a caretaker’s apartment.
If you wish to use this feature enter the apartment address then press .
Otherwise just press
Page 8