US Automatic 030210 Configuration guide

1A - General information
The Transmitter has been designed to control automatic opening
systems and anti-burglar systems.
The operating frequency is 433.92 MHz.
During installation, the receiver must be connected to the device it
controls ( gate, rolling shutters, awnings, anti-burglar appliances,
lighting ).
The transmitter security code is created by 9 ways three-position dip-
switches. This allows up to 19,683 code combinations.
1A - General information 1B -
Technical specifications 1C -
Main features
1D - Model Types
1 - TRANSMITTER INTRODUCTION
2 - SECURITY CODE
3 - PROGRAMMING
4 - BATTERY AND DIP-SWITCH ACCESS
5 - TROUBLESHOOTING
CONTENTS
Thank you for choosing this product.
Please read this manual carefully before using the product.
Transmitter
2-Button
Part # 030210
4-Button
Part # 030212
BUTTON 1
CHANNEL A
RED
LED
RED LED
BATTERY
DOOR
BUTTON 2
CHANNEL B
BUTTON 4
CHANNEL D
All the receivers for this transmitter type can store the code for
multiple transmitters into the receiver’s memory.
Each transmitter ( or its different buttons) can also be stored into
multiple receivers to perform additional functions.
99/5/CE, 89/336/CEE, 73/23/CEE and with the Part 15 of FCC
Regulations.
1B - Technical specifications
2 / 4
1 Alkaline Battery 12V type 23A
12 - 18 months
25 mA
433.92 MHz
19683
AM / ASK
50 - 100 µW
180 - 360 feet
0 - 130 °F
3.26 x 1.88 x 0.62 in
20 gr.
Number of keys: Supply :
Battery Type:
Battery life:
Current consumption :
Operating frequency :
Code combinations :
Modulation :
Rated e.r.p. :
Range in free space:
Operating temperature:
Overall dimensions:
Weight:
1C - Main features
BUTTON 3
CHANNEL C
Made in Italy
2 button dip-switch transmitter : Item 030210
4 button dip-switch transmitter : Item 030212
1D- Model Types

2 - SECURITY CODE
Slide the access panel to the left to access the battery and the dip-switches.
The position of the dip-switches create the security code. Warning: each
transmitter is factory set with a default code.
To help prevent unauthorized access, you must change this code by
changing the positions of the dip-switches to a random pattern. Multiple
transmitters can use the same switch pattern to simplify programming.
The transmitter code has to be stored into the receiver memory before use.
Simply hold down the button on the transmitter you want to use. While
holding the transmitter button down, press the appropriate programming
button (P1 or P2) on the receiver. Once the receiver indicator lights up, you
are done. Any additional transmitters that are set to the same security code
are also programmed at this time.
Contact your dealer or distributor for additional functionality.
3 - PROGRAMMING
Type : SETDS39433
FCC ID : PWJDS433
This device complies with Part. 15 of the FCC Rules
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept interference received, including
interference that may cause undesired operation.
Notice:
Any changes or modification to this equipment not expressly
approved by USAutomatic could void the user's authority to operate
this equipment.
4 - BATTERY AND DIP-SWITCH ACCESS
5 - TROUBLESHOOTING
PROBLEM SOLUTION
Check battery connections.
Replace the transmitter battery.
Check the power supply of the receiver.
Replace the transmitter battery.
Remove coax cable from receiver.
To access the battery rotate the
access panel to the left. Place the 23A
alkaline battery between the 2
contacts. Ensure the polarity is
correct, as indicated on the bottom of
the case.
NOTE: Please dispose of used
batteries properly. They are
hazardous waste.
IS-TDSUAUK Rev.3 del 01/2018
Rotate to open
Rotating door
Dip-switch
Battery
The radio signal is not received
and
Transmitter LED does not light up
The radio signal is not received and
the transmitter LED lights
WARRANTY
USAutomatic, LLC warrants this product to be free of defects in materials and
workmanship for 1 YEAR. For a period of 1 YEAR following purchase
USAutomatic, LLC. will repair or replace the product free of charge, including
parts, shop labor and return to customer shipping and handling.
This 1 YEAR warranty does not cover the plastic case from normal wear or
damage due to misuse.
To have the product sent for warranty consideration, it must be returned with
the proof of purchase and a return authorization number. To obtain a return
authorization number please call 1-888-204-0174 for assistance. The return
authorization number must be clearly marked on the outside of the return
package or it may not be accepted.
USAutomatic LLC
170 Valley Ridge Blvd.
Lewisville, Texas 75057
Ph. 888-204-0174
www.usautomatic.com