US Electronics UY322-EPG User manual

setting up your remote controlbutton functionsbefore you begin
*displays help for on-screen display screens
#future use
MUSIC/ENTER switches between cable TV and Music Choice™
LAST recalls the last channel that was viewed
FAV cycles through your favorite channels
MUTE turns volume off
Pdisplays the quick function screen
◆future use
PPV displays pay-per-view options
EXIT exits the on-screen display menus
INFO displays channel and program information
MENU displays the main on-screen display menu
GUIDE displays the program guide
SEL selects various options and tunes programs from the program guide
CURSOR KEYS navigate through on-screen guides (see the highlighted section above)
PAGE +/- pages through on-screen menu and program guide screens
DAY +/- moves the program guide one day forward and backward
EPG RECORD initiates VCR recording through the on-screen menu (if so equipped)
© 1998 US Electronics Components Corp.All rights reserved
Part Number USE17370,Version 1.1
9804
User’s Guide for the
UY322-EPG
3-in-1 Remote Control
featuring Memory Lock™
and Predictive Technology™
Install two
AAA alkaline batteries
as shown here
If you have a TV with a remote control, we
recommend that you plug its power cord
directly into a wall outlet if available (your
cable installer may select an alternate setup).
Make sure to set your TV to channel 2, 3, or 4
as directed by your cable company.
Before you can program or operate the remote
control, you must install two AAA Alkaline
batteries.
Step 1
Remove the battery compartment cover on the
back of your remote control.
Step 2:
Check battery polarity carefully,and
install the batteries as shown in the
illustration below.
Step 3:
Replace the battery compartment cover.
installing batteries
The chart below shows the functions of special keys for your cable box and program guide.
See the cable box manual for further details.
MORE
INFO
step
2
Press the [TV POWER] button,then the [SETUP] button on the remote.
Enter the 3-digitTV code for your brand ofTV listed in the“TV codes”chart.
Press the [SETUP] button again to save the code.The red indicator light at the upper
right-hand corner of your remote will flash 3 times if these steps were followed correctly.
Press the [TV POWER] button again to test the code you‘ve entered.The TV should
turn ON or OFF each time the [TV POWER] button is pressed. If the TV doesn’t turn
ON and OFF, repeat this TV setup procedure with the next code listed in the “TV
codes”chart.
step
3
Press the [CABLE POWER] button, then the [SETUP] button on the remote.
Enter the 3-digit cable box code listed below.
Press the [SETUP] button again to save the code.The red indicator light at the upper
right-hand corner of your remote will flash 3 times if these steps were followed correctly.
Press the [CABLE POWER] button again to test the code you‘ve entered.The cable box
should turn ON or OFF each time the [CABLE POWER] button is pressed.If the cable box
doesn’t turn ON and OFF,try entering the code again.
Follow these simple steps to program your remote for your VCR,TV,and cable box.
Before you start
■Locate the [SETUP] button, which is at the very bottom of the
remote (see illustration at right).
■Manually turn on yourVCR,TV,and cable box.
STOP RECORD PLAY
REW PAUSE
SETUP
FWD
VCR CONTROLS
The setup code for the
GI/Jerrold™ CFT2200™ series
cable box is
002
Jerrold™ is a trademark of GIC corp.
Helpful
Hint
Following the above steps allows the remote to control
volume through your cable box.If you would like volume
to be controlled through your TV, perform step 3 before
step 2.If you have a combinationTV/VCR,volume will be
controlled only through the cable box.
N
O
T
E
I
N
F
O
for
your
TV
for
your
cable
box
step
1
Press the [VCR POWER] button, then the [SETUP] button on the remote.
Enter the 3-digit VCR code for your brand of VCR listed in the “VCR codes”chart on the
other side of this manual by pressing the appropriate buttons on the numeric key pad.
Press the [SETUP] button again to save the code.The red indicator light at the upper
right-hand corner of your remote will flash 3 times if these steps were followed correctly.
Press the [VCR POWER] button again to test the code you‘ve entered.The VCR
should turn ON or OFF each time the [VCR POWER] button is pressed. If the VCR
doesn’t turn ON and OFF,repeat thisVCR setup procedure with the next code listed in
the“VCR codes”chart.
for
your
VCR
vcr controls
These keys operate standard VCR functions.
Operating Note: Press the [RECORD] button
twice to start recording on yourVCR.
numeric keypad
These keys allow you to enter the channel
you want to view.You will also use them
to setup the remote
cable box
function keys
See the chart below for a description
of the key functions
After you find the correct code for each device,write the code on the supplied sticker.
Depending on the configuration
of your cable box,certain
functions listed below may or
may not be functional.
N
O
T
E
Memory Lock™is an exclusive technology
that saves the device codes that are
programmed into the remote, even when
the batteries are removed.
MEMORY LOCK ™
featuring
Cursor Keys
US Electronics provides these function descriptions as a general guide to allow you to become more familiar with your cable box. Refer to your cable box manual for descriptions of specific functions.
www.uselectronics.com

AOC 010 | 019
Candle 010 | 031 | 037 | 081
Capehart 035
Citizen 010 | 027 | 031 | 037
038 | 046 | 081
Concerto 037
Conklin 000
Contec 028 | 064 | 077 | 080
Craig 066 | 077
Curtis Mathes 010 | 038
CXC 077
Daewoo 019 | 027 | 040 | 041 | 046
Dixi 011
Dynatech 032
Emerson 019 | 076 | 077
078 | 080 | 087
Envision 010
Fisher 060
Funai 076 | 077
GE 003 | 021 | 023
GE 025 | 034 | 036
Goldstar 012 | 019 | 037
Harman Kardon 044
Hitachi 029 | 037 | 050 | 054
048 | 058 | 072 | 085
Infinity 006
JBL 006
Jensen 033
JVC 009 | 065
Kloss Novabeam 022
KTV 077
Logik 018
Luxman 037
LXI 056
Magnavox 006 | 010| 017 | 022
024 | 049 | 081 | 082
Marantz 010
MGA 007 | 010 | 019 | 061
Mitsubishi 007 | 016 | 019
028 | 051 | 061
Mitsubishi Monitor 016
MTC 010 | 019 | 032 | 037 | 038
NEC 010 | 019 | 037 | 070
Panasonic 002 | 006 | 034 | 036 | 067
Penney 001 | 003 | 010 | 019 | 021 | 057
Philco 006 | 010 | 019 | 020
022 | 024 | 081 | 082
Philips 006
Pioneer 008 | 071
Proscan 003
Proton 019 | 026 | 035
Quasar 034 | 036 | 083
Radio shack 027 | 068 | 077
RCA 001 | 003 | 019 | 029
Sampo 010 | 035
Samsung 010 | 019 | 027 | 037 | 038
Sanyo 052 | 055 | 060 | 086
Scott 076
Sears 017 | 055 | 056 | 057
060 | 069 | 076
Sharp 028 | 047 | 059 | 068
Sony 005 | 015 | 045
Soundesign 019 | 081
SSS 019 | 077
Sylvania 006 | 010 | 020 | 022
024 | 039 | 081 | 082
Tatung 032
Techwood 037
Teknika 007 | 018 | 019 | 027
031 | 037 | 038 | 046
073 | 076 | 077 | 081
TMK 037 | 019
Toshiba 060 | 056
Universal 021 | 023
Vidtech 019
Wards 006 | 010 | 018 | 019
020 | 021 | 023 | 024
068 | 076 | 082
Yamaha 019
Zenith 004
Akai 026 | 030 | 034 | 049
Alba 016
Altec 004
Amstrad 005
ASA 008 | 022
Broksonic 061
Canon 001
Craig 028 | 064
Curtis Mathes 001
Daewoo 009 | 015 | 016 | 045
Daytron 016
Dual 026
Dynatech 005 | 029
Emerson 005 | 021 | 020 | 037 | 041 | 046
050 | 058 | 059 | 061 | 062
Ferguson 026
Finlux 005 | 008
Fisher 028 | 035 | 039
Funai 005
GE 001 | 007
Goldstar 022 | 023
Graetz 026
Grundig 008
Harman Kardon 023 | 043
Hitachi 005 | 006 | 026
ITT 026 | 049
JCL 001
Jensen 026
JVC 013 | 026 | 040
Kenwood 026 | 027 | 040
Lloyd 005
Magnavox 001 | 008
Marantz 001 | 008 | 023
Marta 022
MEI 001
MGA 010 | 037
Minolta 006
Mitsubishi 010 | 037 | 063
MTC 005 | 064
Multitech 005 | 042
NEC 023 | 026 | 031 | 040
Normende 026
Panasonic 001 | 003
Penney 001 | 006 | 023
Pentax 006 | 038
Philco 001
Philips 008
Pioneer 036 | 040
Portland 016
Proscan 007
Quasar 001 | 047
RCA 001 | 002 | 006 | 007
Realistic 001 | 005 | 022 | 027
028 | 029 | 048 | 064
Saba 026
Saisho 046 | 059
Salora 010
Samsung 009 | 032 | 064
Sansui 026 | 040
Sanyo 027 | 028
Schaub Lorenz 026
Scott 009 | 062
Sears 006 | 022 | 027 | 028 | 035 | 039
Sharp 029
Shintom 042
Sony 014 | 017 | 018 | 019
Sylvania 001 | 010
Symphonic 005
Tatung 026
Teac 005 | 026
Teknika 001 | 005 | 022 | 033
Telefunken 026
Thomson 026
Thorn 026
TMK 021
Toshiba 009 | 010 | 026
Totevision 022 | 064
Uni-Logic 000
Unitech 064
Vector Research 023
Video Concepts 023
Videosonic 064
Wards 005 | 029 | 064
Yamaha 023 | 026
Zenith 018 | 019 | 024
❚GE 003 ❚JVC 009 ❚Magnavox 006 ❚Mitsubishi 007
❚NEC 010 ❚Panasonic 002 ❚Philips 006 ❚Pioneer 008
❚Proscan 003 ❚RCA 003 ❚Sony 005 ❚Zenith 004
❚GE 007 ❚Hitachi 006 ❚JVC 040 ❚Magnavox 008
❚Mitsubishi 010 ❚Panasonic 003 ❚NEC 023 ❚Proscan 007
❚RCA 007 ❚Sony 018 ❚Toshiba 009 ❚Zenith 024
television codes
vcr codes
helpful hint
notes
find your
code sticker
here
Device 1 ___________ Code: [ ] [ ] [ ] Device 2 ___________ Code: [ ] [ ] [ ] Device 3 ___________ Code: [ ] [ ] [ ] Device 4 ___________ Code: [ ] [ ] [ ]
ASSEMBLED IN MEXICO
Port Jefferson Station, NY USE17079
Write your device codes below
TM
Once you have found your TV, VCR, and Cable
Box codes, write them down for safe keeping
on the code sticker that’s inside the battery
cover (see illustration below). Attach the
“Quick Programming Instructions” sticker to
the outside of the battery cover.
CodeScan™
troubleshooting guide
Problem
I programmed the remote,but it won’t work myTV,VCR, or Cable Box.
Solution
You may have entered the wrong code (or the correct code might not be listed).Try entering
all of the device manufacturer’s codes again, starting with the manufacturer’s popular code if
one is available.
If you are still unable to operate your device, follow the instructions in the section
titled CodeScan™ .
Weak batteries may cause the remote to only operate one device. If this happens, simply
replace them with NEW alkaline batteries and reprogram the remote. If you are sure the
batteries are good,try rolling them with your finger to ensure a good connection.
Problem
My remote control doesn’t operate my combinationTV/VCR.
Solution
Most combination TV/VCRs have VCR tuners in them. You will need to select a code
from the VCR section that will power up your TV/VCR. If this is the case, you probably
won’t need to use a TV code. Also, to control volume with your remote control, you
must program the remote for the cable box last.
Problem
What determines which device operates volume control?
Solution
Volume will be controlled through the device that was programmed last in the section
titled “setting up your remote control.” For example, if the last device you programmed
the remote to operate was your cable box, then the remote will control volume through
your cable box and not yourTV.
If none of the codes listed for your Cable Box,TV, or VCR works, the CodeScan™method will allow you to
cycle through all the available codes in the remote until you find the right Cable Box,TV,or VCR code.
Manually turn ON power to the device you want to program the remote for
(Cable Box,TV,or VCR).
Point the remote control at the device,and press the following keys:
[the device power button](the red buttons at the top of the remote),
[SETUP],[the right arrow key],then [the device power button]
If the device is still ON,continue at step 3 below.If it turns OFF, press [SETUP]
again to store the code you just selected,and you’re all done.
Press [the right arrow key],then [the device power button] until the
device turns OFF.When the device turns OFF, press [SETUP] to save the code.
Please be patient — there are about 90 possible codes.
step 1
step 2
step 3
the right arrow key
If your VCR is made by one of the manufacturers
listed to the right,try that code first.
Otherwise,find your code in the chart below.
If your TV is made by one of the manufacturers
listed to the right,try that code first.
Otherwise,find your code in the chart below.
The setup code for the
GI/Jerrold™ CFT2200™ series cable box is
002
Jerrold™ is a trademark of GIC corp.
cable box code
UY322-EPG manual • version 1.1 • page 2