Utax LP 3118 User manual

Service Manual
Printer
LP 3118
22-02-2005

Service Manual
Printer
LP 4118
22-02-2005

Safety warnings and precautions
Various symbols are used to protect our service personnel and customers from physical danger and
to prevent damage to their property. These symbols are described below:
DANGER: High risk of serious bodily injury or death may result from insufficient attention to or incorrect
compliance with warning messages using this symbol.
WARNING: Serious bodily injury or death may result from insufficient attention to or incorrect compliance
with warning messages using this symbol.
CAUTION: Bodily injury or damage to property may result from insufficient attention to or incorrect
compliance with warning messages using this symbol.
Symbols
The triangle ( ) symbol indicates a warning including danger and caution. The specific point
of attention is shown inside the symbol.
General warning.
Warning of risk of electric shock.
Warning of high temperature.
indicates a prohibited action. The specific prohibition is shown inside the symbol.
General prohibited action.
Disassembly prohibited.
indicates that action is required. The specific action required is shown inside the symbol.
General action required.
Remove the power plug from the wall outlet.
Always ground the printer.

1.Installation Precautions
WARNING
• Do not use a power supply with a voltage other than that specified. Avoid multiple connections to
one outlet: they may cause fire or electric shock. When using an extension cable, always check
that it is adequate for the rated current. .............................................................................................
• Connect the ground wire to a suitable grounding point. Not grounding the printer may cause fire or
electric shock. Connecting the earth wire to an object not approved for the purpose may cause
explosion or electric shock. Never connect the ground cable to any of the following: gas pipes,
lightning rods, ground cables for telephone lines and water pipes or faucets not approved by the
proper authorities. ............................................................................................................................
CAUTION:
• Do not place the printer on an infirm or angled surface: the printer may tip over, causing injury. ......
• Do not install the printer in a humid or dusty place. This may cause fire or electric shock. ...............
• Do not install the printer near a radiator, heater, other heat source or near flammable material.
This may cause fire. .........................................................................................................................
• Allow sufficient space around the printer to allow the ventilation grills to keep the machine as cool
as possible. Insufficient ventilation may cause heat buildup and poor copying performance. ...........
• Always handle the machine by the correct locations when moving it. ...............................................
• Always use anti-toppling and locking devices on printers so equipped. Failure to do this may cause
the printer to move unexpectedly or topple, leading to injury. ...........................................................
• Avoid inhaling toner or developer excessively. Protect the eyes. If toner or developer is acciden-
tally ingested, drink a lot of water to dilute it in the stomach and obtain medical attention immedi-
ately. If it gets into the eyes, rinse immediately with copious amounts of water and obtain medical
attention. ......................................................................................................................................
• Advice customers that they must always follow the safety warnings and precautions in the printer’s
instruction handbook. .....................................................................................................................

2.Precautions for Maintenance
WARNING
• Always remove the power plug from the wall outlet before starting machine disassembly. ...............
• Always follow the procedures for maintenance described in the service manual and other related
brochures. .......................................................................................................................................
• Under no circumstances attempt to bypass or disable safety features including safety mechanisms
and protective circuits. .....................................................................................................................
• Always use parts having the correct specifications. ..........................................................................
• Always use the thermostat or thermal fuse specified in the service manual or other related bro-
chure when replacing them. Using a piece of wire, for example, could lead to fire or other serious
accident. ..........................................................................................................................................
• When the service manual or other serious brochure specifies a distance or gap for installation of a
part, always use the correct scale and measure carefully. ................................................................
• Always check that the printer is correctly connected to an outlet with a ground connection. .............
• Check that the power cable covering is free of damage. Check that the power plug is dust-free. If it
is dirty, clean it to remove the risk of fire or electric shock. ..............................................................
• Never attempt to disassemble the optical unit in machines using lasers. Leaking laser light may
damage eyesight. ...........................................................................................................................
• Handle the charger sections with care. They are charged to high potentials and may cause electric
shock if handled improperly. ............................................................................................................
CAUTION
• Wear safe clothing. If wearing loose clothing or accessories such as ties, make sure they are
safely secured so they will not be caught in rotating sections. ..........................................................
• Use utmost caution when working on a powered machine. Keep away from chains and belts. ........
• Handle the fixing section with care to avoid burns as it can be extremely hot. ..................................
• Check that the fixing unit thermistor, heat and press rollers are clean. Dirt on them can cause
abnormally high temperatures. ........................................................................................................

• Do not remove the ozone filter, if any, from the printer except for routine replacement. ....................
• Do not pull on the AC power cord or connector wires on high-voltage components when removing
them; always hold the plug itself. .....................................................................................................
• Do not route the power cable where it may be stood on or trapped. If necessary, protect it with a
cable cover or other appropriate item. .............................................................................................
• Treat the ends of the wire carefully when installing a new charger wire to avoid electric leaks. ........
• Remove toner completely from electronic components. ...................................................................
• Run wire harnesses carefully so that wires will not be trapped or damaged. ....................................
• After maintenance, always check that all the parts, screws, connectors and wires that were
removed, have been refitted correctly. Special attention should be paid to any forgotten connector,
trapped wire and missing screws. ...................................................................................................
• Check that all the caution labels that should be present on the machine according to the instruction
handbook are clean and not peeling. Replace with new ones if necessary. ......................................
• Handle greases and solvents with care by following the instructions below: .....................................
· Use only a small amount of solvent at a time, being careful not to spill. Wipe spills off completely.
· Ventilate the room well while using grease or solvents.
· Allow applied solvents to evaporate completely before refitting the covers or turning the power
switch on.
· Always wash hands afterwards.
• Never dispose of toner or toner bottles in fire. Toner may cause sparks when exposed directly to
fire in a furnace, etc. .......................................................................................................................
• Should smoke be seen coming from the printer, remove the power plug from the wall outlet imme-
diately. ............................................................................................................................................
3.Miscellaneous
WARNING
• Never attempt to heat the drum or expose it to any organic solvents such as alcohol, other than the
specified refiner; it may generate toxic gas. .....................................................................................

This page is intentionally left blank.

2GL/2FV/2FW
CONTENTS
1-1 Specifications
1-1-1 Specifications..........................................................................................................................................1-1-1
1-1-2 Parts names............................................................................................................................................1-1-7
(1) Printer................................................................................................................................................1-1-7
(2) Operation panel.................................................................................................................................1-1-8
1-1-3 Cross section view ..................................................................................................................................1-1-9
1-2 Handling Precautions
1-2-1 Drum unit and developer unit..................................................................................................................1-2-1
1-2-2 Installation environment ..........................................................................................................................1-2-1
1-3 Installation
1-3-1 Unpacking and installation .....................................................................................................................1-3-1
(1) Installation procedure ........................................................................................................................1-3-1
1-3-2 Installing expansion memory (optional for 16/18 ppm printers) ..............................................................1-3-6
1-3-3 Installing a memory card (optional for 16/18 ppm printers).....................................................................1-3-7
1-4 Maintenance Mode
1-4-1 Service mode ..........................................................................................................................................1-4-1
(1) Executing service mode ....................................................................................................................1-4-1
1-5 Troubleshooting
1-5-1 Paper misfeed detection .........................................................................................................................1-5-1
(1) Paper misfeed indication ...................................................................................................................1-5-1
(2) Paper misfeed detection....................................................................................................................1-5-2
1-5-2 Self-diagnosis .........................................................................................................................................1-5-3
(1) Self-diagnostic function .....................................................................................................................1-5-3
(2) Self diagnostic codes ........................................................................................................................1-5-4
1-5-3 Electric problems ..................................................................................................................................1-5-14
1-5-4 Image formation problems ....................................................................................................................1-5-17
1-5-5 Mechanical problems ............................................................................................................................1-5-23
1-6 Assembly and Disassembly
1-6-1 Precautions for assembly and disassembly............................................................................................1-6-1
(1) Precautions .......................................................................................................................................1-6-1
1-6-2 Outer covers ...........................................................................................................................................1-6-2
(1) Detaching and refitting the right side cover, right cover, left cover, and top cover............................1-6-2
1-6-3 Paper feeding/conveying section ............................................................................................................1-6-4
(1) Detaching and refitting the paper feed roller .....................................................................................1-6-4
(2) Detaching and refitting the transfer roller ..........................................................................................1-6-5
1-6-4 Process section.......................................................................................................................................1-6-6
(1) Detaching and refitting the developer unit and drum unit..................................................................1-6-6
(2) Drum unit optimization.......................................................................................................................1-6-7
(3) Detaching and refitting the main charger unit....................................................................................1-6-8
1-6-5 Fuser unit ................................................................................................................................................1-6-9
(1) Detaching and refitting the fuser unit.................................................................................................1-6-9
(2) Detaching and refitting the heater lamp, heat roller, fuser thermistor, thermal cutout,
and press roller................................................................................................................................1-6-11
1-6-6 PWBs ....................................................................................................................................................1-6-15
(1) Detaching and refitting the main PWB (16 ppm GDI printer) ..........................................................1-6-15
(2) Detaching and refitting the main PWB (16/18 ppm printers) ...........................................................1-6-16
(3) Detaching and refitting the engine/high voltage PWB and power source PWB ..............................1-6-17
1-6-7 Others ...................................................................................................................................................1-6-20
(1) Detaching and refitting the laser scanner unit .................................................................................1-6-20
(2) Detaching and refitting the eraser lamp (PWB)...............................................................................1-6-22
(3) Detaching and refitting the drive unit...............................................................................................1-6-23
(4) Detaching and refitting the main motor ...........................................................................................1-6-24

2GL/2FV/2FW
1-7 Firmware
1-7-1 Downloading ...........................................................................................................................................1-7-1
(1) Firmware program data format.........................................................................................................1-7-1
(2) Downloading the firmware from the parallel interface (For 16/18 ppm printers) ..............................1-7-2
(3) Downloading the firmware from the memory card (For 16/18 ppm printers).....................................1-7-4
2-1 Mechanical Construction
2-1-1 Paper feeding/conveying section ............................................................................................................2-1-1
(1) Paper feed section ............................................................................................................................2-1-1
2-1-2 Drum section...........................................................................................................................................2-1-3
(1) Drum unit...........................................................................................................................................2-1-3
(2) Main charger unit...............................................................................................................................2-1-4
2-1-3 Expose section........................................................................................................................................2-1-5
(1) Laser scanner unit.............................................................................................................................2-1-5
2-1-4 Developing section..................................................................................................................................2-1-7
(1) Developer unit ...................................................................................................................................2-1-7
2-1-5 Transfer section ......................................................................................................................................2-1-9
2-1-6 Cleaning section ...................................................................................................................................2-1-10
2-1-7 Fuser section ........................................................................................................................................2-1-11
(1) Fuser unit ........................................................................................................................................2-1-11
2-1-8 Paper exit section .................................................................................................................................2-1-13
(1) Paper exit section............................................................................................................................2-1-13
2-2 Electrical Parts Layout
2-2-1 Electrical parts layout..............................................................................................................................2-2-1
(1) Electrical parts layout ........................................................................................................................2-2-1
2-3 Operation of the PWBs
2-3-1 Power source PWB.................................................................................................................................2-3-1
2-3-2 Engine/high voltage PWB .......................................................................................................................2-3-3
2-3-3 Main PWB ...............................................................................................................................................2-3-6
2-4 Appendixes
2-4-1 Appendixes .............................................................................................................................................2-4-1
(1) Timing chart No.1 Cassette paper feeding, Paper size A4 (For 16/16 ppm GDI printers) ................2-4-1
(2) Timing chart No.2 Cassette paper feeding, Paper size A4 (For 18 ppm printer) ..............................2-4-2
(3) Timing chart No.3 Manual feed tray paper feeding, Paper size A4...................................................2-4-3
(4) Wiring diagram ..................................................................................................................................2-4-4
(5) Repetitive defects gauge...................................................................................................................2-4-5

2GL/2FV/2FW-1
1-1-1
1-1 Specific ations
1-1-1 Specifications
16 ppm GDI printer (FS-720)
Type ................................................Desktop
Printing system ...............................Electrophotographic printing
Paper type ...................................... Paper cassette: Plain paper (60 to 105 g/m2)
Recycled paper (60 to 105 g/m2)
Thick paper (90 to 105 g/m2)
Manual feed tray: Plain paper (60 to 163 g/m2)
Recycled paper (60 to 163 g/m2)
Thick paper (60 to 163 g/m2)
Special paper: Transparencies, labels, envelopes, postcards, tracing paper
Paper sizes .....................................Paper cassette
A4 (210 ×297 mm)
B5 (182 ×257 mm)
A5 (148 ×210 mm)
Folio (210 ×330 mm)
Letter (81/2" ×11")
Legal (81/2" ×14")
Officio II (81/2" ×13")
Non-standard size (148 ×210 mm to 216 ×356 mm)
Manual feed tray
A4 (210 ×297 mm)
B5 (182 ×257 mm)
A5 (148 ×210 mm)
Folio (210 ×330 mm)
Letter (81/2" ×11")
Legal (81/2" ×14")
Officio II (81/2" ×13")
Non-standard size (70 ×148 mm to 216 ×356 mm)
Print speeds....................................A4: 16 pages/minutes
Letter: 17 pages/minutes
First print time ................................. 11 seconds or less (ready), 21 seconds or less (sleep)
Warm-up time ................................. 16 seconds or less (power on), 12 seconds or less (sleep)
Paper feed system.......................... One universal cassette and one manual feed tray
Paper loading capacity ...................Paper cassette: 250 sheets (80 g/m2, 0.11 µm)
Manual feed tray: 1 sheet (80 g/m2, 0.11 µm)
Paper exit system .............................. Face down: 100 sheets (80 g/m
2
, 0.11 µ m)
Photoconductor............................... OPC drum (diameter 30 mm)
Charging system.............................Scorotron (positive charging)
Developing system ......................... Mono component dry developing method
Toner replenishing: Automatic from the toner container
Transfer system .............................. Transfer roller (negative-charged)
Separation system ..........................Small diameter separation
Fixing system.................................. Heat roller system
Charge erasing system................... Exposure by eraser lamp (LED)
Cleaning system .............................Drum: Counter blade

2GL/2FV/2FW
1-1-2
Controller hardware ........................ CPU: 32 bit RISC CPU
System ROM: 1 Mbit (on-board)
Main RAM: 8 MB (on-board)
Interface.......................................... USB: Full-Speed USB2.0
Controller software..........................Host based
Resolution....................................... 600 dpi mode (600 ×600 dpi)
Dimensions (H ×W ×D) .................245 ×380 ×390 mm/9.6" ×15.0" ×15.4"
Weight.............................................Main unit: 9.2 kg/20.3 lbs
Power source.................................. 220 - 240 V AC, 50/60 Hz (European countries), 120 V AC, 60 Hz (U.S.A./Canada)
Power consumption ........................Maximum: 830 W (220 - 240 V model), 823 W (120 V model)
Normal operating: 302 W (220 - 240 V model), 295 W (120 V model)
Ready: 5 W (220 - 240 V model), 5 W (120 V model)
EcoPower: 4.2 W (220 - 240 V model), 3.8 W (120 V model)
Current............................................3.4 A (220 - 240 V model), 6.8 A (120 V model)
Noise...............................................Printing: 49 dB(A), Ready: 28 dB(A)

2GL/2FV/2FW-1
1-1-3
16 ppm printer (FS-820)
Type ................................................Desktop
Printing system ...............................Electrophotographic printing
Paper type ...................................... Paper cassette: Plain paper (60 to 105 g/m2)
Recycled paper (60 to 105 g/m2)
Thick paper (90 to 105 g/m2)
Manual feed tray: Plain paper (60 to 163 g/m2)
Recycled paper (60 to 163 g/m2)
Thick paper (60 to 163 g/m2)
Special paper: Transparencies, labels, envelopes, postcards, tracing paper
Paper sizes .....................................Paper cassette
A4 (210 ×297 mm)
B5 (182 ×257 mm)
A5 (148 ×210 mm)
Folio (210 ×330 mm)
Letter (81/2" ×11")
Legal (81/2" ×14")
Officio II (81/2" ×13")
Non-standard size (148 ×210 mm to 216 ×356 mm)
Manual feed tray
A4 (210 ×297 mm)
B5 (182 ×257 mm)
A5 (148 ×210 mm)
Folio (210 ×330 mm)
Letter (81/2" ×11")
Legal (81/2" ×14")
Officio II (81/2" ×13")
Non-standard size (70 ×148 mm to 216 ×356 mm)
Print speeds....................................A4: 16 pages/minutes
Letter: 17 pages/minutes
First print time ................................. 11 seconds or less (ready), 21 seconds or less (sleep)
Warm-up time ................................. 16 seconds or less (power on), 12 seconds or less (sleep)
Paper feed system.......................... One universal cassette and one manual feed tray
Paper loading capacity ...................Paper cassette: 250 sheets (80 g/m2, 0.11 µm)
Manual feed tray: 1 sheet (80 g/m2, 0.11 µm)
Paper exit system .............................. Face down: 100 sheets (80 g/m
2
, 0.11 µ m)
Photoconductor............................... OPC drum (diameter 30 mm)
Charging system.............................Scorotron (positive charging)
Developing system ......................... Mono component dry developing method
Toner replenishing: Automatic from the toner container
Transfer system .............................. Transfer roller (negative-charged)
Separation system ..........................Small diameter separation
Fixing system.................................. Heat roller system
Charge erasing system................... Exposure by eraser lamp (LED)
Cleaning system .............................Drum: Counter blade

2GL/2FV/2FW
1-1-4
Controller hardware ........................ CPU: PowerPC405 (192 MHz)
System ROM: 4 MB (on-board)
Font ROM: Including System ROM
Main RAM: 16 MB standard (on-board); expanding up to 272 MB (256 MB ×1) at the
maximum by adding optional expansion memory
Optional expansion RAM (DIMM): 1 slot
100-pin DIMM (64, 128 or 256 MB)
Interface.......................................... Parallel: Hi-speed (bi-directional), IEEE 1284 Nibble/ECP mode
USB: Full-Speed USB2.0
Controller software..........................a) Emulation
PCL6 (PCL5e/PCL-XL)
b) Fonts:
Bitmap font:
1 font
Outline fonts:
14 fonts
c) Graphic:
(1) Raster graphic:
75, 100, 150, 200*, 300, 600* dpi
(*200 dpi is supported when the resolution is 600 dpi.)
(2) Vector graphic:
Line, Box, Circle, Arc, Fill pattern etc.
(3) Bar code:
One dimensional bar code: 45 types
Two dimensional bar code: 1 type (PDF-417)
(4) Text:
TEXT, RTXT etc.
(5) Others:
Macro, JOB, Device setting etc.
d) Connectivity
Plug &play (Parallel): Windows 9x/Me/2000/XP
Plug & play (Full-Speed USB2.0): Windows 98SE/Me/2000/XP
Resolution....................................... Fast1200 mode (1800 ×600 dpi)
600 dpi mode (600 ×600 dpi)
Dimensions (H ×W ×D) .................245 ×380 ×390 mm/9.6" ×15.0" ×15.4"
Weight.............................................Main unit: 9.2 kg/20.3 lbs
Power source.................................. 220 - 240 V AC, 50/60 Hz (European countries), 120 V AC, 60 Hz (U.S.A./Canada)
Power consumption ........................Maximum: 833 W (220 - 240 V model), 828 W (120 V model)
Normal operating: 319 W (220 - 240 V model), 292 W (120 V model)
Ready: 7 W (220 - 240 V model), 6 W (120 V model)
EcoPower: 4.5 W (220 - 240 V model), 4 W (120 V model)
Current............................................3.4 A (220 - 240 V model), 6.8 A (120 V model)
Noise...............................................Printing: 49 dB(A), Ready: 28 dB(A)
Options ...........................................Expansion memory (64/128/256 MB 100-pin DIMM),
memory card (Compact Flash)

2GL/2FV/2FW-1
1-1-5
18 ppm printer (FS-920)
Type ................................................Desktop
Printing system ...............................Electrophotographic printing
Paper type ...................................... Paper cassette: Plain paper (60 to 105 g/m2)
Recycled paper (60 to 105 g/m2)
Thick paper (90 to 105 g/m2)
Manual feed tray: Plain paper (60 to 163 g/m2)
Recycled paper (60 to 163 g/m2)
Thick paper (60 to 163 g/m2)
Special paper: Transparencies, labels, envelopes, postcards, tracing paper
Paper sizes .....................................Paper cassette
A4 (210 ×297 mm)
B5 (182 ×257 mm)
A5 (148 ×210 mm)
Folio (210 ×330 mm)
Letter (81/2" ×11")
Legal (81/2" ×14")
Officio II (81/2" ×13")
Non-standard size (148 ×210 mm to 216 ×356 mm)
Manual feed tray
A4 (210 ×297 mm)
B5 (182 ×257 mm)
A5 (148 ×210 mm)
Folio (210 ×330 mm)
Letter (81/2" ×11")
Legal (81/2" ×14")
Officio II (81/2" ×13")
Non-standard size (70 ×148 mm to 216 ×356 mm)
Print speeds....................................A4: 18 pages/minutes
Letter: 19 pages/minutes
First print time ................................. 11 seconds or less (ready), 21 seconds or less (sleep)
Warm-up time ................................. 16 seconds or less (power on), 12 seconds or less (sleep)
Paper feed system.......................... One universal cassette and one manual feed tray
Paper loading capacity ...................Paper cassette: 250 sheets (80 g/m2, 0.11 µm)
Manual feed tray: 1 sheet (80 g/m2, 0.11 µm)
Paper exit system .............................. Face down: 100 sheets (80 g/m
2
, 0.11 µ m)
Photoconductor............................... OPC drum (diameter 30 mm)
Charging system.............................Scorotron (positive charging)
Developing system ......................... Mono component dry developing method
Toner replenishing: Automatic from the toner container
Transfer system .............................. Transfer roller (negative-charged)
Separation system ..........................Small diameter separation
Fixing system.................................. Heat roller system
Charge erasing system................... Exposure by eraser lamp (LED)
Cleaning system .............................Drum: Counter blade

2GL/2FV/2FW
1-1-6
Controller hardware ........................ CPU: PowerPC405 (266 MHz)
System ROM: 4 MB (on-board)
Font ROM: Including System ROM
Main RAM: 32 MB standard (on-board); expanding up to 288 MB (256 MB ×1) at the
maximum by adding optional expansion memory
Optional expansion RAM (DIMM): 1 slot
100-pin DIMM (64, 128 or 256 MB)
Interface.......................................... Parallel: Hi-speed (bi-directional), IEEE 1284 Nibble/ECP mode
USB: Full-Speed USB2.0
Controller software..........................a) Emulation
PCL6 (PCL5e/PCL-XL)
KPDL3
Line Printer
Diablo 630
IBM Proprinter X24E
Epson LQ850
b) Fonts:
Bitmap font:
1 font
Outline fonts:
80 fonts
c) Graphic:
(1) Raster graphic:
75, 100, 150, 200*, 300, 600* dpi
(*200 dpi is supported when the resolution is 600 dpi.)
(2) Vector graphic:
Line, Box, Circle, Arc, Fill pattern etc.
(3) Bar code:
One dimensional bar code: 45 types
Two dimensional bar code: 1 type (PDF-417)
(4) Text:
TEXT, RTXT etc.
(5) Others:
Macro, JOB, Device setting etc.
d) Connectivity
Plug &play (Parallel): Windows 9x/Me/2000/XP
Plug & play (Full-Speed USB2.0): Windows 98SE/Me/2000/XP
Resolution....................................... Fast1200 mode (1800 ×600 dpi)
600 dpi mode (600 ×600 dpi)
Dimensions (H ×W ×D) .................245 ×380 ×390 mm/9.6" ×15.0" ×15.4"
Weight.............................................Main unit: 9.2 kg/20.3 lbs
Power source.................................. 220 - 240 V AC, 50/60 Hz (European countries), 120 V AC, 60 Hz (U.S.A./Canada)
Power consumption ........................Maximum: 827 W (220 - 240 V model), 827 W (120 V model)
Normal operating: 315 W (220 - 240 V model), 294 W (120 V model)
Ready: 8 W (220 - 240 V model), 7 W (120 V model)
EcoPower: 4.8 W (220 - 240 V model), 4.4 W (120 V model)
Current............................................3.4 A (220 - 240 V model), 6.8 A (120 V model)
Noise...............................................Printing: 49 dB(A), Ready: 28 dB(A)
Options ...........................................Expansion memory (64/128/256 MB 100-pin DIMM),
memory card (Compact Flash)

2GL/2FV/2FW
1-1-7
1-1-2 Parts names
(1) Printer
Figure 1-1-1










 

16 ppm GDI printer 16/18 ppm printer
1. Top cover
2. Operation panel
3. Output tray
4. Paper cassette
5. Manual feed tray
6. Paper gauge
7. Paper stopper
8. Right side cover
9. Rear cover
10. AC inlet
11. Power switch
12. Toner container
13. USB interface connector
14. Parallel interface connector

2GL/2FV/2FW
1-1-8
(2) Operation panel
Figure 1-1-2
READY
indicator
GO key
ATTENTION
indicator
CANCEL key

2GL/2FV/2FW
1-1-9
1-1-3 Cross section view
Figure 1-1-3








Paper path




1. Paper cassette
2. Manual feed tray
3. Paper feeding/conveying section
4. Toner container
5. Developer unit
6. Main charger unit
7. Drum unit
8. Laser scanner unit
9. Transfer section
10. Fuser unit
11. Paper exit section
12. Output tray

2GL/2FV/2FW
1-1-10
This page is intentionally left blank.

2GL/2FV/2FW
1-2-1
1-2 Handling Precautions
1-2-1 Drum unit and developer unit
Note the following when handling or storing the drum (drum unit).
• When removing the drum (drum unit), never expose the drum surface to strong direct light.
• Avoid abrupt changes in temperature and humidity.
• Avoid exposure to any substance which is harmful to or may affect the quality of the drum.
• Do not touch the drum surface with any object. Should it be touched by hands or stained with oil, clean it.
Developer unit and toner container
Store the developer unit and toner container in a cool, dark place.
Avoid direct light and high humidity.
1-2-2 Installation environment
1. Temperature: 10 - 32.5 °C/50 - 90.5 °F
2. Humidity: 20 - 80%RH
3. Power supply: 120 V AC (U.S.A./Canada), 220 - 240 V AC (European countries)
4. Power source frequency: 50 Hz ±2%/60 Hz ±2%
5. Installation location
• Avoid direct sunlight or bright lighting. Ensure that the photo-conductor will not be exposed to direct sunlight or other
strong light when removing paper jams.
• Avoid extremes of temperature and humidity, abrupt ambient temperature changes, and hot or cold air directed onto
the machine.
• Avoid dust and vibration.
• Choose a surface capable of supporting the weight of the machine.
• Place the machine on a level surface (maximum allowance inclination: 1°).
• Avoid air-borne substances that may adversely affect the machine or degrade the photo-conductor, such as mercury,
acidic of alkaline vapors, inorganic gasses, NOx, SOx gases and chlorine-based organic solvents.
• Select a room with good ventilation.
6. Allow sufficient access for proper operation and maintenance of the machine.
Machine front: 50 cm/19.7" Machine rear: 20 cm/7.9"
Machine right: 15 cm/5.9" Machine left: 15 cm/5.9"
Machine top: 30 cm/11.8"
Figure 1-2-1 Installation dimensions
a
cb
a: 245 mm/9.6"
b: 380 mm/15.0"
c: 390 mm/15.4"