UTEK ULTRALOQ User manual

ULTRALOQBoltFingerprint
Installation and User Guide
( )
V2.0

• Do not use a power drill for installation.
• Install and test the lock with the door open to avoid being
locked out.
• Please read all the instructions before contacting customer
support.
• Please contact customer support before returning the
product to the store.
• Do not install the batteries before installing the lock!
• Follow the instructions in sequential order!
• This lock is designed for the following operating temperatures:
Outside: -4°F(-20°C)to149°F(65°C)
Inside: 14 °F (-10 °C) to 131 °F (55 °C)
• Suggest to use AA Alkaline Battery, or manufacture suggested
Lithium Battery. Don’t use Rechargeable Battery.
To ensure the best service, please register your account at
www.u-tec.com/register.html
Need Help?
For technical documents and more
Please visit support.u-tec.com
Important Notes
Statements
- 1 -
Before using all ULTRALOQ products, please read all
applicable terms, rules, policies and usage provisions found at
www.u-tec.com/company/privacy. By using your
ULTRALOQ, you agree to be bound by the U-tec Privacy Policy.
ULTRALOQ Terms & Policies
Note:The Exterior Assembly of ULTRALOQ Bolt
Fingerprint is waterproof, but the Interior Assembly is not
waterproof at all due to the battery box.

ENGLISH
- 2 -
Packing List
Screw AStrike Bolt
Screw FScrew E AA Alkaline Batteries
May not be included
for some regions
Interior
Assembly
Exterior
Assembly
Interior Assembly
Mounting Plate
Screw C Screw DScrew B
User Guide Drill Template Reset Needle
DrillTemplate
(V1.6)
Faceof the door Edgeofthe door
Centerline
Backset
2
3
/
4
”
(70mm)
2
3
/
8
” (60mm)
1
3
/
4
”
(44mm)
1
3
/
8
”
(35mm)
Centerline
Backset
2
3
/
4
”
(70mm)
2
3
/
8
” (60mm)
1
3
/
4
”
(44mm)
1
3
/
8
”
(35mm)
Fold
(V1.6)
Plantillade Perforación
Carade la puerta Bordedelapuerta
Eje
Carade la puertaBordede la puerta
Eje
Doblar
Entradade
lacerradura
Entradade
lacerradura
Fold
Doblar
DrillTemplate
(V1.6)
(V1.5)
Plantillade Perforación
Faceof the doorEdge of the door
2”(50mm)
2”
(50mm)
Backup KeyDoor Sensor

Installation Guide
Installation Video
- 3 -
1. Preparing Door
Check the door’s dimensions.
Step 1
Measure to confirm that the door is between 13
/
8”
~ 13
/
4”
(35 mm-45 mm) thick.
If your door is thicker than
13
/
4”
, please visit support.u-tec.com
to get help.
Step 2
Measure to confirm that the diameter of the hole is 21
/
8 ”
(53
mm) or
11
/
2 ”
(38 mm)
Step 3
Measure to confirm that the backset is either 23
/
8 ” or 23
/
4
”
(60 mm or 70 mm).
Step 4
Measure to confirm that the diameter of the hole in the door
edge is
1” (25 mm).
Step 5
Measure to confirm the depth of the hole in the frame is at least
1''(25 mm).
If you have a new door, please drill the holes according to Drill
Template.
Please scan this QR code to watch the easy
step by step installation video before
attempting to install ULTRALOQ.
Or you can also view the webiste directly.
www.u-tec.com/lock/Bolt_F_WiFi/guide
1”
25 mm
53 mm
(35 mm ~ 45 mm)
13
/
8”
~ 13
/
4”
2
3
/
4 ”
2
3
/
8 ”
(70 mm)
OR
(60 mm)
38mm
1
1
/
2
”
1''(25 mm)
21
/
8 ”

- 4 -
2. Installing Bolt and Strike
Note: Bolt is set for 2
3
/
8
” backset initially. It can be
adjusted to 2
3
/
4
” if needed.
To adjust it please make sure the bolt is retracted,
then, press it, twist and pull it or push it to your desired
length.
Step 2
Install Strike into the door frame.
Step 1
Install Bolt into the door. Make sure the UP icon goes up.
23
/ 8 ”
2 3
/
4
”
(60 mm)
(70 mm)
Adjust the Bolt
basket length
Screw A
Screw C
Screw B
ENGLISH

- 5 -
Step 1
Keep Bolt retracted and the cylinder tailpiece horizontal.
Install ExteriorAssembly. Please do not insert the
mechanical key during installation .
Step 2
Align its two sticks with two holes on Bolt. The cable goes
through the hole below Bolt.
If your door has a
11
/
2 ”
(38 mm) bore hole, remove the
spacer as shown.
3. Installing Exterior Assembly

- 6 -
Step 1
Route the cable through the hole on Interior Assembly
Mounting Plate.
Step 2
Secure Interior Assembly Mounting Plate to Exterior
Assembly using Screws D.
4. Installing Interior Assembly Mounting Plate
Screw D
ENGLISH

Pull Up
- 7 -
5. Installing Interior Assembly
Step 1
Remove the battery cover of the Interior Assembly.
Step 2
Insert the connector of the cable to the socket on Interior
Assembly. When you plug the connector, please make sure the
black teeth faces up. Press the connector in firmly until it is
completed seated.
Step 3
Rotate the knob and keep it in a vertical position to stay
unlocked.
Step 4
Attach Interior Assembly to Mounting Plate and tighten 2
Screws E.
Warning: Please do not install the batteries before installing interior assembly,
otherwise the keypad may not be powered on.
Screw E
Unlocked

The door sensor lets you know whether the door is open or
closed through the App. When the auto lock is enabled in the
App, your ULTRALOQ will only lock it self when the door is
closed.
Please do not mount the door sensor on the keypad side.
Please do not mount the door sensor on the kind of metal
door that interferes with the magnet inside the door sensor
(In this case, the door sensor sticks to the metal door
magnetically).
The door sensor can be installed on the wooden door or the
kind of metal door that will not interfere with the door sensor
(In this case, the door sensor will not stick to the door
magnetically).
- 8 -
7. Installing the Door Sensor(Optional)
6. Installing the Batteries and Performing the
Door Handing Process
This step will teach your lock the orientation of your door and is
crucial to lock operation.
Step 1
Rotate the turn and keep it in a vertical position to stay
unlocked.
Step 2
Insert 8 AA Alkaline Batteries and keep the batteries on the
battery pull tab. Then install the battery cover.
Note：Any Fingerprint or pressing any digit button for 4 times can unlock
ULTRALOQ Bolt Fingerprint in Factory Default Mode.
Step 3
Direction calibration: Please keep Bolt
unlocked and press and hold the
number 5 until you hear two short
beeps, then the lock will rotate to start
the direction self-calibration.
To avoid deadbolt jamming, please note
that this step should be done after the
lock is installed on the door.
ENGLISH

Note: Please refer to the guide in U-tec App for more information.
Door
Frame
Option 1 Installing with Sticker
Peel o either side of the sticker and push it against the door
frame about 10s. Peel o the other side and secure the door
sensor on the sticker firmly. Put on the door sensor cover at last.
Option 2 Installing with Screw F
Push the door sensor against the wall and secure it with Screw
F. You may need to drill a hole first if the door frame is hard to
screw in with Screw F directly. Put on the door sensor cover at
last.
UP
Door
Frame
UP
Door
Frame
Note:Door sensor should be
mounted as close to the edge
of your door frame as possible,
or within 0 to 1''(25 mm) from
the edge, and as close to the
bottom of the extended
deadbolt as possible, or within
0 to 1''(25 mm) from the edge.
- 9 -
Door
Frame

ENGLISH
ENGLISH
- 10 -
User Guide
1. Product Overview
1.1 Exterior
User Guide Video
Advanced
Fingerprint Reader
Communication
Indicator
Checkmark
Indicator
Anti-peep Keypad
Low Battery
Indicator
”X”Indicator
ULTRALOQ Button Backup Key Hole
Anti-peep Keypad
Used to enter the code and unlock from outside.
Advanced Fingerprint Reader
Used to verify your finger and unlock from the outside.
Checkmark Indicator
It will light on when manual programming is successful or
your entry verification is correct.
”X”Indicator
It will light on when your manual programming is failed or
your entry verification is wrong.
Communication Indicator
It will splash when the lock is communicating with your
App or Internet.
Low Battery Indicator
It will light on when the battery is low.
Backup Key Hole
Used to insert the key to unlock in emergency situations.
Please watch our easy step by step User Guide video on the
left before attempting to use your ULTRALOQ Bolt 
Fingerprint Smart Lock(Or you can also view the webiste
directly.www.u-tec.com/lock/Bolt_F_WiFi/guide).
For the configuration guide of integration (such as Alexa,
etc.), please check the QR code on the right
(or visit:
https://support.u-tec.com/hc/en-us/categories/360005956492)

- 11 -
Battery Cover
Used to cover batteries and product label.
Turn
Used to unlock and lock the door from inside.
LED Indicator
Turns red when door is unlocked.
1.3 Low Battery Alarm
There will be low battery alert on the lock and App when
battery is low. The Low Battery Indicator will light on when the
lock is activated. Please replace batteries.
Reset Button
Used to reset the lock to Factory Default settings.
If the lock was paired to App, please must click "Remove
Device" to remove the device from App.
Battery Pull Tab
Use the battery pull tab to lift and remove the batteries from
the battery box.
Battery Compartments
Used to insert 8 AA Alkaline Battery, or manufacture
suggested Lithium Battery. Don’t use Rechargeable Battery.
1.2 Interior
ULTRALOQ Button
Used to lock from the outside, illuminate the keypad for code
entry and confirm previous operation etc.
Reset Button
Battery
Compartments
Battery Cover
Turn
LED Indicator
Battery Pull Tab
RESET

- 12 -
ENGLISH
Step 1
Scan above QR code to download the App, or search
“U-tec”in App Store (iOS) and Google Play (Android).
Step 2
Open the App, register U-tec account and log in the account.
Step 3
Make sure the lock is in Factory Default Mode. Turn on
Bluetooth on your smartphone, stay near the lock (within 10
feet ) and search the lock in the App. If you want to reset your
lock to Factory Default Mode, Please check the page 14.
Step 4
Pair the lock in the App and start to use it.
DON’T WANT TO USE THE APP?
Please go to page 16 for programming guide for Standalone
Mode.
2. Lock Setup
Note: Please refer to the guide in U-tec App for more information.
Scan QR code to download the App

- 13 -
3. Using Your Lock
• User Code
• Fingerprint
Place your finger on Fingerprint Reader to unlock.
• Smartphone
Use your smartphone to unlock. Please refer to the guide
in U-tec App.
3.1 Unlock From Outside
Enter 4-8 digit code and press ULTRALOQ Button to unlock .

- 14 -
ENGLISHENGLISH
3.2 Lock From Outside
Press ULTRALOQ Button to lock manually.
Enable Auto Lock feature and the lock will relock
automatically.
3.3 Unlock From Inside
Rotate the turn to a vertical position to unlock.
3.4 Reset the Lock
Please note all data will be erased if you reset ULTRALOQ
BoltFingerprint to factory default. If you are using U-tec
App as Owner, please click “Remove Device” to remove the
lock from your U-tec Account, then you hear one long beep
and two short beeps, it means reset successfully. If you have
already removed the lock from your U-tec Account, but the
lock doesn’t reset itself, please use a Reset Needle to push
the Reset Button(at the bottom of InteriorAssembly) for 10
seconds until you hear one long beep and two short beeps.
3.5 Replace Batteries
Please use 8 high-quality alkaline AA batteries for
replacement when the battery is dead.
3.6 Enable Or Disable Auto Lock
Enable
Please keep Bolt unlocked and press "1" button for 3 seconds
until Checkmark Indicator lights on and hear two beeps.
Disable
Please keep Bolt unlocked and press "0" button for 3 seconds
until Checkmark Indicator lights on and hear two beeps.
This can also be set in U-tec App and Auto Lock timing can be
programmed by yourself.
Important Note
Please keep at least one key in secure location outside
of your place.

- 15 -
3.7 Anti-peep Keypad
The lock supports up to 16-digit Vague Code. Just enter any
16-digit code, as long as a correct code is included in what you
entered, you can open the door.
1:
2:
3:
1 2 3 4 5 6 X X X X X X
1 2 3 4 5 6
X X X X X X
1 2 3 4 5 6
X X X X X X
Example
User Code: 123456
Vague Code
3.8 Place Finger
1. For a higher recognition rate, please try to cover the
Fingerprint Reader completely with your finger, touching the
surrounding metal ring.
2. Make sure that your finger and Fingerprint Reader are clean
and dry. For Fingerprint Reader, use a clean, lint-free cloth to
wipe o any dirt or debris.
3. Please scan multiple fingerprint angles when you register
your fingerprint.
4. While scanning your finger, you shouldn't tap too quickly or
move your finger around.
5. If you have trouble enrolling one finger, try another.
6. ULTRALOQBoltFingerprint sensor has self-study function
which the verification rate will be improved after multiple
success .
Bottom View Top View Side View

- 16 -
4.2 Add User Code in Standalone Mode
Warning
Standalone Mode is NOT available after the lock is registered
in App! Please reset the lock to Factory Default Mode first to
program your lock in Standalone Mode.
Admin Code must be created first prior to any other
programming. Only one Admin Code is available.
4. Standalone Mode Programming Guide
IndicatorOperation
4.1 Add Admin Code in Standalone Mode
Hold for 3 sec 2 beeps with light on
Enter 4-8 digit Admin Code
and press 2 beeps with light on
2 beeps with light on
Enter the Admin Code again
and press
Success All lights o
IndicatorOperation
Hold for 3 sec
Enter 4-8 digit Admin Code
and press
Enter 4-8 digit User Code
and press
It is recommended to use U-tec App to program your lock.
If you don’t have a smartphone or don’t want to use the
App, you may follow the programming instructions below.
2 beeps with light on
2 beeps with light on
2 beeps with light on
ENGLISH

- 17 -
4.3 Add Fingerprint in Standalone Mode
Success All lights o
Enter the User Code again
and press
IndicatorOperation
Press Fingerprint 6 times
Hold for 3 sec
Enter 4-8 digit Admin Code
and press
4.4 Delete Admin and User
Please reset the lock to Factory Default Mode to delete
Admin and all Users.
How to reset the lock in Standalone Mode?
Please use a Reset Needle to push the Reset Button (at the
bottom of Interior Assembly) for 10 seconds until you hear
one long beep and two short beeps.
Success All lights o
2 beeps with light on
2 beeps with light on
2 beeps with light on
5 beeps and digit
buttons blink 5 times

- 18 -
FAQ
1. How to reset ULTRALOQBoltFingerprint?
Please note all data will be erased if you reset ULTRALOQBolt
Fingerprint to factory default.
If you are using U-tec App as Owner, please click “Remove
Device” to remove the lock from your U-tec Account, then
use a Reset Needle to push the Reset Button (at the
bottom of Interior Assembly) for 10 seconds until you hear
one long beep and two short beeps.
If ULTRALOQBoltFingerprint is working as Standalone Mode,
please use a Reset Needle to push the Reset Button (at the
bottom of Interior Assembly) for 10 seconds until you hear one
long beep and two short beeps.
2. What if I lost the paired smartphone?
Please go to www.u-tec.com/myutec.html or login U-tec App
via another smartphone to change your U-tec Account
password.
3. How can I unlock ULTRALOQBoltFingerprint if
the battery runs out?
There will be low battery alert on the lock and App when battery
is low. Low Battery Indicator will light on when the lock is
activated. Please replace batteries.
Use the backup key to unlock. Please keep at least one key in
secure location outside of your place.
4. What’s the dierence between Owner, Admin,
Normal User and Temporary User?
Owner is the person who owns ULTRALOQBoltFingerprint
and registers it in U-tec App originally. Owner has all privileges.
Admin can always unlock via fingerprint, code or App. Admin
can add or delete Admin and Users, control all lock settings and
view logs.
Normal User can always unlock via fingerprint, code or App.
Temporary User has limited access within specific time range.
ENGLISH

- 19 -
5. Does ULTRALOQBoltFingerprint work with
accessories such as bolt from third party?
It is recommended to use the original accessories for best
performance and stability.
6. What is the log capacity for ULTRALOQBolt
Fingerprint?
ULTRALOQBoltFingerprint supports maximum 1,000 logs.
The latest log will replace the oldest one once log is full.
7. What is the user capacity for ULTRALOQBolt
Fingerprint?
ULTRALOQBoltFingerprint supports maximum 50 users and
each user can register 1 code and 2 fingerprints.
8. How to extend battery life of ULTRALOQBolt
Fingerprint?
You can disable the Remote Access to Lock function in the
U-tec APP. After turning o the Remote Access to Lock
function,battery life will be approximately doubled.
Remote operation,smart control such as Alexa,Google
Assistant,IFTTT and smart notifications will all be unavailable if
turned o.
9. Does ULTRALOQBoltFingerprint need to be
paired with an ULTRALOQ Bridge?
No, it is a smart lock with built-in WiFi. No extra hub required.
10. What is the network requirement?
ULTRALOQBoltFingerprint can only work with the 2.4G WiFi
network (5G WiFi NOT supported).