UTEPO N3-GSW0802T-POE User manual

Please follow installation steps as below:
Please check the following items before installation, if it is missing, please contact the dealer.
Ethernet Switch 1pc
AC Power Cable 1pc
Accessory 1pc
User Manual 1pc
1) Turn off the power of all the related devices before the installation; otherwise the device would be
damaged;
)
)
4)
5)
6)
2 Connect PoE cameras with 1~8 downlink ports of product by Ethernet cable;
3 Connect UPLINK port of product with NVR or PC by Ethernet cable;
Connect power adapter;
Check if the installation is correct, equipment is in good condition, the connection is stable,then
power on for system;
Ensure the Ethernet equipment with power on can work properly.
Installaiton Steps
Feature
12
Board Diagram
Main Function:
Ethernet ports ;
Compliance with standards: IEEE802.3 、IEEE802.3u、IEEE802.3ab、IEEE802.3z、
IEEE802.3X、 IEEE802.3af/at;
PoE Power Display: Support 8 LED digital tube display machine POE power usage. whole
machine reaches 135W PoE power output;
One-key Smart: Support three kinds of working modes (Default, VLAN, CCTV);
Protection: Support 6KV surge immunity, EFT testing standard;
Operation Environment: Support -10℃~45℃ wide-temperature;
Operation: Plug&play, convenient to use, support desktop, wall-mounted installations.
Provide 8*10/100/1000Base-T Ethernet ports(PoE) ,2* 10/100/1000BASE-T
Application
The transmission distance depends on the signal source and cable quality; standard Cat5e/6
Ethernet cable is strongly suggested for reaching the maximum transmission distance!
Notice
1) Device must be connected with lightning protection grounding; otherwise protection level will be
greatly reduced; please use above No.20 wire to connect the grounding terminal;
2) The device requires rebooting after the dial switch has been utilized.
Back Board
Front Board
4口百兆以太网交换机
8 Ports Gigabit PoE Ethernet Switch
ing and other occasions.
8 Ports Gigabit PoE Ethernet Switch
Ethernet access and PoE applications. It provides eight Gigabit downlink ports, two Gigabit uplink
Ethernet port, The eight downlink ports support 802.3af/at standard and feature Max 30W PoE
power output of single port, Max 135W of whole machine. Support three kinds of work mode
(Default, VLAN, CCTV), and supports 8 LED digital tube display machine PoE power usage. It can
be widely used in security surveillance, hotels, schools, SMB engineer
is an unmanaged Ethernet switch designed for Gigabit
V1.0
One key smart
Power LED
Power Port
PoE Ethernet Ports Uplink Ethernet Port
Grounding
8 Ports Gigabit PoE Ethernet Switch
User Manual
Notice
Cat5e/6
LCD
NVR
IP Camera
8 Ports Gigabit PoE Switch
AP
AP
IP Camera
POE power display
AP

Item
Description
Downlink Ports
8x10/100/1000Base-T Ethernet Ports(PoE)
Uplink Ports
2x 10/100/1000Base-TEthernet Ports
Network Standard
Support IEEE 802.3/802.3u/IEEE802.3ab/IEEE802.3z/IEEE802.3x
Switch Capacity
20Gbps
Packet Forwarding Rate
14Mpps
Buffer
1M
MAC Address List
4K
PoE Standard
802.3af/at(PSE)
PoE Mode
End-span
PoE Power Supply
1/2(+)，3/6(-)
PoE Output
Single PoE Output≤30W(54V DC), Whole machine PoE output≤135W
PoE power display
Support 8 LED digital tube to display machine PoE power usage
One-key Smart
Default: All ports are free to communicate
VLAN: The downs ports are isolated from each other
CCTV: Optimize flow control for port isolation
Surge Immunity
6KV
ESD Protection
Contact discharge 6K, Air discharge 8KV, Per: IEC61000-4-2
Voltage Input
AC 110V~240V
Power Consumption
5W
Operation Temperature
-10℃~+45℃
Storage Temperature
-40℃~+85℃
Operation Humidity
5%-95%(Non-condensing)
Dimensions(LxWxH)
245mm×245mm×44mm
Material
Metal
Weight
1kg
连接接口 连接接口
34
Product parameters are project to change without prior notice.
连接接口
Trouble Shooting
If any trouble with operation, please follow these steps to do troubleshooting:
Please make sure you have followed the instruction to install the device;
Please confirm if the RJ45 cable order is in accordance with the EIA/TIA568A or 568B industry
standards;
The power supply of each PoE port is no more than 30W; please do not connect the PoE device
whichexceeds the maximum PoE power supply;
Please replace a failure device with a proper one to check if the device is broken;
Please contact your vendor if trouble still exists.
Specification
4口百兆以太网交换机
8 Ports Gigabit PoE Ethernet Switch
Pin color
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
1
2
3
4
5
6
7
8
Pin color
1
2
3
4
5
6
7
8
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
EIA/TIA 568A EIA/TIA 568B
RJ 45 Making Method
Tools to make RJ45: wire crimper, network tester.
Wire sequence of RJ45 plug should conform with EIA/TIA568A or EIA/TIA568B standard.
1) Strip off the 2cm insulating layer to expose the 4 pairs UTP cable;
2) Seperate the 4 pairs of UTP cable and straighten them;
3) Line up the 8 separated pieces of cables per EIA/TIA 568A or 568B;
4) Cut the cables to leave 1.5cm bare wire and make sure 8 thread ends are flat and neat ;
5) Insert 8 cables into RJ45 plugs, make sure each cable is inserted in each pin;
6)Then use wire crimper to crimp the RJ45;
7) Do the above 5 steps again to make the another end of the twisted pair and make sure
consistent cable order between two ends ;
8) Using network tester to test the cable.
Notice
When choose RJ-45 make sure if one end is EIA/TIA568B,the other end should also be EIA/TIA568B.
When choose RJ-45 make sure if one end is EIA/TIA568A,the other end should also be EIA/TIA568A.
4口百兆以太网交换机
8 Ports Gigabit PoE Ethernet Switch