UTEPO UTP3-SW04-FP60 User manual

Please follow the below installation steps
Please check the following items before installation, if it is missing, please contact the
dealer .
4 ports PoE Ethernet Switch 1pc
Power adaptor 1pc
AC power cable 1pc
Accessory 1pc
User manual 1pc
1) Please turn off the signal power and display device power before installation, installation
with power will damage the transmission equipment;
2) Use network cable connect PoE IP camera and 1～4 downlink ports of product respectively;
3) Use fiber connect equipment uplink optical port and uplink equipment’s(optical converter)
optical port, please notice that the fiber port RX and TX need cross-linking .
4) Connect power adapter;
5) Check if the installation is correct, equipment is in good condition, the connection is stable,
then provide power for system;
6) Ensure the Ethernet equipment with power and work properly.
Feature
4 Ports PoE Ethernet Switch
4 Ports PoE Ethernet Switch
User Manual
12
4 ports PoE Ethernet Switch is a surveillance security Ethernet Switch which aims at Ethernet
high definition surveillance, Ethernet project security system. The product fully combines the
characteristic of surveillance security, provides fast packet forwarding ability and abundant
backplane bandwidth, which ensures clear image and fluent transmission. ESD and surge
protection circuit can improve product stability. The product supports one key CCTV model,
can achieve VLAN, control the Net storm, protect the information security, prevent the viral
transmission and Ethernet attack, fully satisfy the Ethernet video surveillance security system
and Ethernet project needs.
VerB 1.3
● Major ports: 1 pcs 100Mbps uplink optical port, 4 pcs 100Mbps down link Ethernet
ports , every port supports MDI/MDIX;
● Special function: One key CCTV model;1～4 downlink ports can only communicate
with uplink ports;
● Power input: DC48V～57V;
● Transmission Distance : Ethernet port 0～100m，the furthest transmission distance
could reach 250m in CCTV model; Optical port 20km;
● Standard: Meet IEEE802.3 ,IEEE802.3u,IEEE802.3 af/at standards, PoE use
End-Span, the spare cable can be of other use;
● Protection: Excellent anti-thunder, anti-static and anti-interference ability;
● Appearance: Delicate design and easy installation, configure the anti-theft lock hole,
guard against theft;
●Operation: Plug and Play, No Setting required.
fiber
4 Ports POE Ethernet Switch
Cat5/5e/6 network cable
PoE IP camera
power
Optical Fiber Converter
PoE IP camera
Application
Board Diagram
Front board
CCTV mode
Power indicated light
Optical port
indicated light
PoE down link
Ethernet port
Uplink Ethernet port
Power input port
Ground
Kensington lock
Back board
Side board
Notice
The transmission distance is related to the connected cable. We suggest standard
Cat5e/6 network cable, so the transmission distance can up to furthest!
1
level will reduce; please use above No.20 wire to connect the grounding terminal.
2) Turn the dial switch for left, the equipment can enter surveillance mode after providing
equipment power.
) Device must be connected with lightning protection grounding; otherwise protection
Notice
NVR
Installation steps
PoE IP camera

连接接口
Specification
连接接口
4 Ports PoE Ethernet Switch
34
Specification change will not be noticed
4 Ports PoE Ethernet Switch
Trouble Shooting
Please follow the steps if the equipment has trouble.
Make sure the equipment is installed according to the manufactures installation guide.
Confirm RJ45 cable order meets EIA/TIA568A or 568B standard.
Every PoE port can provide PoE equipment maximum power less than 30W, please do not
connect the PoE equipment with power over 30W.
Replace the equipment with a proper functioning 4 ports PoE Ethernet Switch to check if the
equipment is damaged.
Please contact your vendor if trouble still exists.
Instruments to be used: wire crimper, network tester. Wire sequence of RJ45 plug should
conform with EIA/TIA568A or 568B.
1) Please remove 2cm long the insulating layer, and bare 4 pairs UTP cable;
2) Separate the 4 pairs UTP cable and straighten them;
3) Line up the 8 pieces of cables per EIA/TIA 568A or 568B;
4) Cut off the cables to leave 1.5cm bare wire;
5) Plug 8 cables into RJ45 plug, make sure each cable is in each pin;
6) Use the wire crimper to crimp it;
7) Repeat above 5 steps to make the another end;
8) Use network tester to test the cable if it works.
Plug Producing Method
Pin Color
White/Green
Green
Blue
White/Orange
White/Blue
White/Brown
Orange
Brown
1
2
3
4
5
6
7
8
Pin Color
1
2
3
4
5
6
7
8
White/Green
Green
Blue
White/Orange
White/Blue
White/Brown
Orange
Brown
EIA/TIA 568A EIA/TIA 568B
When choose RJ45 make sure if one end is EIA/TIA568A,the other end should also be EIA/TIA568A.
When choose RJ45 make sure if one end is EIA/TIA568B,the other end should also be EIA/TIA568B.
Notice
Item
Description
Power
Power Supply
Power Adaptor
Voltage Range
DC48V~54V
Consumption
＜5W
Ethernet
Speed
1-4 port:Default:10/100Mbps;
CCTV:10Mbps;
UPLINK:100Mbps
Transmission Distance
1-4 port:Default:0～100m;
CCTV:0~250m;
UPLINK:20Km
Network Switch
Ethenet Standard
IEEE 802.3/802.3u/802.3af/at
Exchange Capacity
1.0Gbps
Packet Forwarding Rate
0.74Mpps
Packet Buffer
768K
MAC
2K
Status Indicator
Power Light
1pc(Red)
Ethernet Port Light
2pcs(Yellow&Green) on RJ45,yellow indicates PoE,
green indicates Link/Act
Optical Light
1pc(green), green indicates Link/Act
Surveillance Module Light
1pc(Green), green indicates CCTV
Protection Level
Pluse Group
Level 3
Standard: IEC61000-4-4
ESD
1a Contact Discharge Level 3
1b Air Discharge Level 3
Standard: IEC61000-4-2
Anti-thunder Level
6KV
Standard: IEC61000-4-5
Working
Environment
Working Temperature
-10 ~55℃℃
Storage Temperature
-40 ~85℃℃
Humidity(Non-condesing)
0~95%
Mechanical
Dimension(L*W*H)
135mm×85.6mm×27mm
Out Shell
Galvanized Sheet
Color
Black
Weight
315g
Power/Distance
54V
Distance
100m
150m
200m
250m
Power
26W
24W
23W
21W