Utilitech 148007 User manual

1. Pump (A) should be located within 15 ft. of the water
source, and strainer (C) should be used at the end of
the inlet line. Attach hose adapters (B) and reinforced
suction hose (not provided) to pump. Make sure inlet
connection is air tight. NOTE: Regular garden hose
should not be used on pump (A) inlet. It will collapse
when the pump runs. Hoses that expand and contract
will not allow the pump to operate.
3. PUMP MUST BE PRIMED BEFORE USING!
Remove priming plug from the top of pump (A).
Fill pump (A) housing with clean water. Reinstall
plug.
DO NOT RUN DRY.
4. Plug in power cord to grounded outlet. Pump
(A) will prime in a few minutes, depending on
suction line length.
SW1113 B
QUICK START
GUIDE.
SEE INSTRUCTION
MANUAL FOR
COMPLETE DETAILS.
WARNING:
FOR YOUR PROTECTION, ALWAYS DISCONNECT
PUMP FROM POWER SOURCE BEFORE HANDLING.
IN
OUT
2. Attach discharge hose (not provided) to pump
(A) outlet. A standard 3/4 in. garden hose may be
used as a discharge line.
CAUTION: Keep the total length as short as
possible for best performance.
IN
OUT
5. If the pump (A) does not pump water after ve
minutes, turn o󰀨 the pump and repeat steps 1
through 3.
DO NOT RUN DRY.
ITEM #0955642
UTILITY
TRANSFER
PUMP
MODEL # 148007
Printed in China
AB
C
Use only rigid pipe or
reinforced hose on the
pump inlet. Hoses that
expand and contract will
not allow the pump to
operate.
Toll Free Help Line: 1-866-994-4148
AA
AA

1. Pump (A) should be located within 15 ft. of the water
source, and strainer (C) should be used at the end of
the inlet line. Attach hose adapters (B) and reinforced
suction hose (not provided) to pump. Make sure inlet
connection is air tight. NOTE: Regular garden hose
should not be used on pump (A) inlet. It will collapse
when the pump runs. Hoses that expand and contract
will not allow the pump to operate.
3. PUMP MUST BE PRIMED BEFORE USING!
Remove priming plug from the top of pump (A).
Fill pump (A) housing with clean water. Reinstall
plug.
DO NOT RUN DRY.
4. Plug in power cord to grounded outlet. Pump
(A) will prime in a few minutes, depending on
suction line length.
SW1113 B
QUICK START
GUIDE.
SEE INSTRUCTION
MANUAL FOR
COMPLETE DETAILS.
WARNING:
FOR YOUR PROTECTION, ALWAYS DISCONNECT
PUMP FROM POWER SOURCE BEFORE HANDLING.
IN
OUT
2. Attach discharge hose (not provided) to pump
(A) outlet. A standard 3/4 in. garden hose may be
used as a discharge line.
CAUTION: Keep the total length as short as
possible for best performance.
IN
OUT
5. If the pump (A) does not pump water after ve
minutes, turn o󰀨 the pump and repeat steps 1
through 3.
DO NOT RUN DRY.
ITEM #0955642
UTILITY
TRANSFER
PUMP
MODEL # 148007
Printed in China
AB
C
Use only rigid pipe or
reinforced hose on the
pump inlet. Hoses that
expand and contract will
not allow the pump to
operate.
Toll Free Help Line: 1-866-994-4148
AA
AA

1. Pump (A) should be located within 15 ft. of the water
source, and strainer (C) should be used at the end of
the inlet line. Attach hose adapters (B) and reinforced
suction hose (not provided) to pump. Make sure inlet
connection is air tight. NOTE: Regular garden hose
should not be used on pump (A) inlet. It will collapse
when the pump runs. Hoses that expand and contract
will not allow the pump to operate.
3. PUMP MUST BE PRIMED BEFORE USING!
Remove priming plug from the top of pump (A).
Fill pump (A) housing with clean water. Reinstall
plug.
DO NOT RUN DRY.
4. Plug in power cord to grounded outlet. Pump
(A) will prime in a few minutes, depending on
suction line length.
SW1113 B
QUICK START
GUIDE.
SEE INSTRUCTION
MANUAL FOR
COMPLETE DETAILS.
WARNING:
FOR YOUR PROTECTION, ALWAYS DISCONNECT
PUMP FROM POWER SOURCE BEFORE HANDLING.
IN
OUT
2. Attach discharge hose (not provided) to pump
(A) outlet. A standard 3/4 in. garden hose may be
used as a discharge line.
CAUTION: Keep the total length as short as
possible for best performance.
IN
OUT
5. If the pump (A) does not pump water after ve
minutes, turn o󰀨 the pump and repeat steps 1
through 3.
DO NOT RUN DRY.
ITEM #0955642
UTILITY
TRANSFER
PUMP
MODEL # 148007
Printed in China
AB
C
Use only rigid pipe or
reinforced hose on the
pump inlet. Hoses that
expand and contract will
not allow the pump to
operate.
Toll Free Help Line: 1-866-994-4148
AA
AA

1. Pump (A) should be located within 15 ft. of the water
source, and strainer (C) should be used at the end of
the inlet line. Attach hose adapters (B) and reinforced
suction hose (not provided) to pump. Make sure inlet
connection is air tight. NOTE: Regular garden hose
should not be used on pump (A) inlet. It will collapse
when the pump runs. Hoses that expand and contract
will not allow the pump to operate.
3. PUMP MUST BE PRIMED BEFORE USING!
Remove priming plug from the top of pump (A).
Fill pump (A) housing with clean water. Reinstall
plug.
DO NOT RUN DRY.
4. Plug in power cord to grounded outlet. Pump
(A) will prime in a few minutes, depending on
suction line length.
SW1113 B
QUICK START
GUIDE.
SEE INSTRUCTION
MANUAL FOR
COMPLETE DETAILS.
WARNING:
FOR YOUR PROTECTION, ALWAYS DISCONNECT
PUMP FROM POWER SOURCE BEFORE HANDLING.
IN
OUT
2. Attach discharge hose (not provided) to pump
(A) outlet. A standard 3/4 in. garden hose may be
used as a discharge line.
CAUTION: Keep the total length as short as
possible for best performance.
IN
OUT
5. If the pump (A) does not pump water after ve
minutes, turn o󰀨 the pump and repeat steps 1
through 3.
DO NOT RUN DRY.
ITEM #0955642
UTILITY
TRANSFER
PUMP
MODEL # 148007
Printed in China
AB
C
Use only rigid pipe or
reinforced hose on the
pump inlet. Hoses that
expand and contract will
not allow the pump to
operate.
Toll Free Help Line: 1-866-994-4148
AA
AA

1. Pump (A) should be located within 15 ft. of the water
source, and strainer (C) should be used at the end of
the inlet line. Attach hose adapters (B) and reinforced
suction hose (not provided) to pump. Make sure inlet
connection is air tight. NOTE: Regular garden hose
should not be used on pump (A) inlet. It will collapse
when the pump runs. Hoses that expand and contract
will not allow the pump to operate.
3. PUMP MUST BE PRIMED BEFORE USING!
Remove priming plug from the top of pump (A).
Fill pump (A) housing with clean water. Reinstall
plug.
DO NOT RUN DRY.
4. Plug in power cord to grounded outlet. Pump
(A) will prime in a few minutes, depending on
suction line length.
SW1113 B
QUICK START
GUIDE.
SEE INSTRUCTION
MANUAL FOR
COMPLETE DETAILS.
WARNING:
FOR YOUR PROTECTION, ALWAYS DISCONNECT
PUMP FROM POWER SOURCE BEFORE HANDLING.
IN
OUT
2. Attach discharge hose (not provided) to pump
(A) outlet. A standard 3/4 in. garden hose may be
used as a discharge line.
CAUTION: Keep the total length as short as
possible for best performance.
IN
OUT
5. If the pump (A) does not pump water after ve
minutes, turn o󰀨 the pump and repeat steps 1
through 3.
DO NOT RUN DRY.
ITEM #0955642
UTILITY
TRANSFER
PUMP
MODEL # 148007
Printed in China
AB
C
Use only rigid pipe or
reinforced hose on the
pump inlet. Hoses that
expand and contract will
not allow the pump to
operate.
Toll Free Help Line: 1-866-994-4148
AA
AA

1. Pump (A) should be located within 15 ft. of the water
source, and strainer (C) should be used at the end of
the inlet line. Attach hose adapters (B) and reinforced
suction hose (not provided) to pump. Make sure inlet
connection is air tight. NOTE: Regular garden hose
should not be used on pump (A) inlet. It will collapse
when the pump runs. Hoses that expand and contract
will not allow the pump to operate.
3. PUMP MUST BE PRIMED BEFORE USING!
Remove priming plug from the top of pump (A).
Fill pump (A) housing with clean water. Reinstall
plug.
DO NOT RUN DRY.
4. Plug in power cord to grounded outlet. Pump
(A) will prime in a few minutes, depending on
suction line length.
SW1113 B
QUICK START
GUIDE.
SEE INSTRUCTION
MANUAL FOR
COMPLETE DETAILS.
WARNING:
FOR YOUR PROTECTION, ALWAYS DISCONNECT
PUMP FROM POWER SOURCE BEFORE HANDLING.
IN
OUT
2. Attach discharge hose (not provided) to pump
(A) outlet. A standard 3/4 in. garden hose may be
used as a discharge line.
CAUTION: Keep the total length as short as
possible for best performance.
IN
OUT
5. If the pump (A) does not pump water after ve
minutes, turn o󰀨 the pump and repeat steps 1
through 3.
DO NOT RUN DRY.
ITEM #0955642
UTILITY
TRANSFER
PUMP
MODEL # 148007
Printed in China
AB
C
Use only rigid pipe or
reinforced hose on the
pump inlet. Hoses that
expand and contract will
not allow the pump to
operate.
Toll Free Help Line: 1-866-994-4148
AA
AA