Utilitech 148003 User manual

WARNING:
FOR YOUR PROTECTION, ALWAYS
DISCONNECT PUMP FROM POWER
SOURCE BEFORE HANDLING.
2 in. on
.4 in. off
Discharge
1-1/4 in.
Pipe
Base
1. Install the snap-
on strainer (C) by
lining up the pump
(A) base to match
the strainer. Push
down gently until it
latches.
2. Attach 1-1/4 in. pipe or
tting (not included) to
pump (A) discharge,
or screw the garden
hose adapter/check
valve (B) into the pump
discharge.
NOTE: Be sure the
garden hose adapter/
check valve is installed
with the word ‘Top’
facing up.
3. If using garden hose
(not included), thread
the female end of the
garden hose into the
male end of the garden
hose adapter (B).
For best performance,
unwind the hose before
starting the pump.
4. Place pump (A) in an
upright position on
the pool cover where
water will collect. Do
not suspend pump (A)
by the discharge hose
or power cord.
Be sure pump (A) is
not sitting in mud,
sand, or debris.
5. Plug the pump into a properly
grounded, GFCI 115 V
outlet. For safety, the pump
should always be electrically
grounded to a suitable
electrical ground, such as a
grounded water pipe, properly
grounded metallic raceway, or
ground wire.
6. The pump (A) will turn
on when the water
level around the pump
reaches approximately
2 in. Water must contact
the pump sensors in
order for it to turn on.
When the water level
drops to approximately
.4 in., pump (A) will run
for 10 additional seconds
and then turn o󰀨.
QUICK START GUIDE. SEE INSTRUCTION
MANUAL FOR COMPLETE DETAILS.
ITEM #0955587
UTILITY POOL COVER PUMP
MODEL # 148003
SW1181 B
A
A
A
A
A
Printed in China
C
B

WARNING:
FOR YOUR PROTECTION, ALWAYS
DISCONNECT PUMP FROM POWER
SOURCE BEFORE HANDLING.
2 in. on
.4 in. off
Discharge
1-1/4 in.
Pipe
Base
1. Install the snap-
on strainer (C) by
lining up the pump
(A) base to match
the strainer. Push
down gently until it
latches.
2. Attach 1-1/4 in. pipe or
tting (not included) to
pump (A) discharge,
or screw the garden
hose adapter/check
valve (B) into the pump
discharge.
NOTE: Be sure the
garden hose adapter/
check valve is installed
with the word ‘Top’
facing up.
3. If using garden hose
(not included), thread
the female end of the
garden hose into the
male end of the garden
hose adapter (B).
For best performance,
unwind the hose before
starting the pump.
4. Place pump (A) in an
upright position on
the pool cover where
water will collect. Do
not suspend pump (A)
by the discharge hose
or power cord.
Be sure pump (A) is
not sitting in mud,
sand, or debris.
5. Plug the pump into a properly
grounded, GFCI 115 V
outlet. For safety, the pump
should always be electrically
grounded to a suitable
electrical ground, such as a
grounded water pipe, properly
grounded metallic raceway, or
ground wire.
6. The pump (A) will turn
on when the water
level around the pump
reaches approximately
2 in. Water must contact
the pump sensors in
order for it to turn on.
When the water level
drops to approximately
.4 in., pump (A) will run
for 10 additional seconds
and then turn o󰀨.
QUICK START GUIDE. SEE INSTRUCTION
MANUAL FOR COMPLETE DETAILS.
ITEM #0955587
UTILITY POOL COVER PUMP
MODEL # 148003
SW1181 B
A
A
A
A
A
Printed in China
C
B

WARNING:
FOR YOUR PROTECTION, ALWAYS
DISCONNECT PUMP FROM POWER
SOURCE BEFORE HANDLING.
2 in. on
.4 in. off
Discharge
1-1/4 in.
Pipe
Base
1. Install the snap-
on strainer (C) by
lining up the pump
(A) base to match
the strainer. Push
down gently until it
latches.
2. Attach 1-1/4 in. pipe or
tting (not included) to
pump (A) discharge,
or screw the garden
hose adapter/check
valve (B) into the pump
discharge.
NOTE: Be sure the
garden hose adapter/
check valve is installed
with the word ‘Top’
facing up.
3. If using garden hose
(not included), thread
the female end of the
garden hose into the
male end of the garden
hose adapter (B).
For best performance,
unwind the hose before
starting the pump.
4. Place pump (A) in an
upright position on
the pool cover where
water will collect. Do
not suspend pump (A)
by the discharge hose
or power cord.
Be sure pump (A) is
not sitting in mud,
sand, or debris.
5. Plug the pump into a properly
grounded, GFCI 115 V
outlet. For safety, the pump
should always be electrically
grounded to a suitable
electrical ground, such as a
grounded water pipe, properly
grounded metallic raceway, or
ground wire.
6. The pump (A) will turn
on when the water
level around the pump
reaches approximately
2 in. Water must contact
the pump sensors in
order for it to turn on.
When the water level
drops to approximately
.4 in., pump (A) will run
for 10 additional seconds
and then turn o󰀨.
QUICK START GUIDE. SEE INSTRUCTION
MANUAL FOR COMPLETE DETAILS.
ITEM #0955587
UTILITY POOL COVER PUMP
MODEL # 148003
SW1181 B
A
A
A
A
A
Printed in China
C
B

WARNING:
FOR YOUR PROTECTION, ALWAYS
DISCONNECT PUMP FROM POWER
SOURCE BEFORE HANDLING.
2 in. on
.4 in. off
Discharge
1-1/4 in.
Pipe
Base
1. Install the snap-
on strainer (C) by
lining up the pump
(A) base to match
the strainer. Push
down gently until it
latches.
2. Attach 1-1/4 in. pipe or
tting (not included) to
pump (A) discharge,
or screw the garden
hose adapter/check
valve (B) into the pump
discharge.
NOTE: Be sure the
garden hose adapter/
check valve is installed
with the word ‘Top’
facing up.
3. If using garden hose
(not included), thread
the female end of the
garden hose into the
male end of the garden
hose adapter (B).
For best performance,
unwind the hose before
starting the pump.
4. Place pump (A) in an
upright position on
the pool cover where
water will collect. Do
not suspend pump (A)
by the discharge hose
or power cord.
Be sure pump (A) is
not sitting in mud,
sand, or debris.
5. Plug the pump into a properly
grounded, GFCI 115 V
outlet. For safety, the pump
should always be electrically
grounded to a suitable
electrical ground, such as a
grounded water pipe, properly
grounded metallic raceway, or
ground wire.
6. The pump (A) will turn
on when the water
level around the pump
reaches approximately
2 in. Water must contact
the pump sensors in
order for it to turn on.
When the water level
drops to approximately
.4 in., pump (A) will run
for 10 additional seconds
and then turn o󰀨.
QUICK START GUIDE. SEE INSTRUCTION
MANUAL FOR COMPLETE DETAILS.
ITEM #0955587
UTILITY POOL COVER PUMP
MODEL # 148003
SW1181 B
A
A
A
A
A
Printed in China
C
B

WARNING:
FOR YOUR PROTECTION, ALWAYS
DISCONNECT PUMP FROM POWER
SOURCE BEFORE HANDLING.
2 in. on
.4 in. off
Discharge
1-1/4 in.
Pipe
Base
1. Install the snap-
on strainer (C) by
lining up the pump
(A) base to match
the strainer. Push
down gently until it
latches.
2. Attach 1-1/4 in. pipe or
tting (not included) to
pump (A) discharge,
or screw the garden
hose adapter/check
valve (B) into the pump
discharge.
NOTE: Be sure the
garden hose adapter/
check valve is installed
with the word ‘Top’
facing up.
3. If using garden hose
(not included), thread
the female end of the
garden hose into the
male end of the garden
hose adapter (B).
For best performance,
unwind the hose before
starting the pump.
4. Place pump (A) in an
upright position on
the pool cover where
water will collect. Do
not suspend pump (A)
by the discharge hose
or power cord.
Be sure pump (A) is
not sitting in mud,
sand, or debris.
5. Plug the pump into a properly
grounded, GFCI 115 V
outlet. For safety, the pump
should always be electrically
grounded to a suitable
electrical ground, such as a
grounded water pipe, properly
grounded metallic raceway, or
ground wire.
6. The pump (A) will turn
on when the water
level around the pump
reaches approximately
2 in. Water must contact
the pump sensors in
order for it to turn on.
When the water level
drops to approximately
.4 in., pump (A) will run
for 10 additional seconds
and then turn o󰀨.
QUICK START GUIDE. SEE INSTRUCTION
MANUAL FOR COMPLETE DETAILS.
ITEM #0955587
UTILITY POOL COVER PUMP
MODEL # 148003
SW1181 B
A
A
A
A
A
Printed in China
C
B

WARNING:
FOR YOUR PROTECTION, ALWAYS
DISCONNECT PUMP FROM POWER
SOURCE BEFORE HANDLING.
2 in. on
.4 in. off
Discharge
1-1/4 in.
Pipe
Base
1. Install the snap-
on strainer (C) by
lining up the pump
(A) base to match
the strainer. Push
down gently until it
latches.
2. Attach 1-1/4 in. pipe or
tting (not included) to
pump (A) discharge,
or screw the garden
hose adapter/check
valve (B) into the pump
discharge.
NOTE: Be sure the
garden hose adapter/
check valve is installed
with the word ‘Top’
facing up.
3. If using garden hose
(not included), thread
the female end of the
garden hose into the
male end of the garden
hose adapter (B).
For best performance,
unwind the hose before
starting the pump.
4. Place pump (A) in an
upright position on
the pool cover where
water will collect. Do
not suspend pump (A)
by the discharge hose
or power cord.
Be sure pump (A) is
not sitting in mud,
sand, or debris.
5. Plug the pump into a properly
grounded, GFCI 115 V
outlet. For safety, the pump
should always be electrically
grounded to a suitable
electrical ground, such as a
grounded water pipe, properly
grounded metallic raceway, or
ground wire.
6. The pump (A) will turn
on when the water
level around the pump
reaches approximately
2 in. Water must contact
the pump sensors in
order for it to turn on.
When the water level
drops to approximately
.4 in., pump (A) will run
for 10 additional seconds
and then turn o󰀨.
QUICK START GUIDE. SEE INSTRUCTION
MANUAL FOR COMPLETE DETAILS.
ITEM #0955587
UTILITY POOL COVER PUMP
MODEL # 148003
SW1181 B
A
A
A
A
A
Printed in China
C
B

WARNING:
FOR YOUR PROTECTION, ALWAYS
DISCONNECT PUMP FROM POWER
SOURCE BEFORE HANDLING.
2 in. on
.4 in. off
Discharge
1-1/4 in.
Pipe
Base
1. Install the snap-
on strainer (C) by
lining up the pump
(A) base to match
the strainer. Push
down gently until it
latches.
2. Attach 1-1/4 in. pipe or
tting (not included) to
pump (A) discharge,
or screw the garden
hose adapter/check
valve (B) into the pump
discharge.
NOTE: Be sure the
garden hose adapter/
check valve is installed
with the word ‘Top’
facing up.
3. If using garden hose
(not included), thread
the female end of the
garden hose into the
male end of the garden
hose adapter (B).
For best performance,
unwind the hose before
starting the pump.
4. Place pump (A) in an
upright position on
the pool cover where
water will collect. Do
not suspend pump (A)
by the discharge hose
or power cord.
Be sure pump (A) is
not sitting in mud,
sand, or debris.
5. Plug the pump into a properly
grounded, GFCI 115 V
outlet. For safety, the pump
should always be electrically
grounded to a suitable
electrical ground, such as a
grounded water pipe, properly
grounded metallic raceway, or
ground wire.
6. The pump (A) will turn
on when the water
level around the pump
reaches approximately
2 in. Water must contact
the pump sensors in
order for it to turn on.
When the water level
drops to approximately
.4 in., pump (A) will run
for 10 additional seconds
and then turn o󰀨.
QUICK START GUIDE. SEE INSTRUCTION
MANUAL FOR COMPLETE DETAILS.
ITEM #0955587
UTILITY POOL COVER PUMP
MODEL # 148003
SW1181 B
A
A
A
A
A
Printed in China
C
B

WARNING:
FOR YOUR PROTECTION, ALWAYS
DISCONNECT PUMP FROM POWER
SOURCE BEFORE HANDLING.
2 in. on
.4 in. off
Discharge
1-1/4 in.
Pipe
Base
1. Install the snap-
on strainer (C) by
lining up the pump
(A) base to match
the strainer. Push
down gently until it
latches.
2. Attach 1-1/4 in. pipe or
tting (not included) to
pump (A) discharge,
or screw the garden
hose adapter/check
valve (B) into the pump
discharge.
NOTE: Be sure the
garden hose adapter/
check valve is installed
with the word ‘Top’
facing up.
3. If using garden hose
(not included), thread
the female end of the
garden hose into the
male end of the garden
hose adapter (B).
For best performance,
unwind the hose before
starting the pump.
4. Place pump (A) in an
upright position on
the pool cover where
water will collect. Do
not suspend pump (A)
by the discharge hose
or power cord.
Be sure pump (A) is
not sitting in mud,
sand, or debris.
5. Plug the pump into a properly
grounded, GFCI 115 V
outlet. For safety, the pump
should always be electrically
grounded to a suitable
electrical ground, such as a
grounded water pipe, properly
grounded metallic raceway, or
ground wire.
6. The pump (A) will turn
on when the water
level around the pump
reaches approximately
2 in. Water must contact
the pump sensors in
order for it to turn on.
When the water level
drops to approximately
.4 in., pump (A) will run
for 10 additional seconds
and then turn o󰀨.
QUICK START GUIDE. SEE INSTRUCTION
MANUAL FOR COMPLETE DETAILS.
ITEM #0955587
UTILITY POOL COVER PUMP
MODEL # 148003
SW1181 B
A
A
A
A
A
Printed in China
C
B