UTStarcom F1000 Series User manual

1
REGULATORY STATEMENT (R&TTE /
WLAN IEEE 802.11B)
European standards dictate maximum radiated transmit power of 100mW
EIRP and frequency range 2.400-2.4835GHz; In France, the equipment
must be restricted to the 2.4465-2.4835GHz frequency range and must be
restricted to indoor use.
CE DECLARATION OF CONFORMITY
For the following equipment: WiFi handset F1000
Is herewith confirmed to comply with the requirements set out in the Council
Directive on the Approximation of the Laws of the Member States relating to
Electromagnetic Compatibility (89/336/EEC), Low-voltage Directive
(73/23/EEC) and the Amendment Directive (93/68/EEC), the procedures
given in European Council Directive 99/5/EC and 89/3360EEC.
The equipment was passed. The test was performed according to the
following European standards:
 EN 300 328 V.1.4.1 (2003-04)
 EN 301 489-1 V.1.3.1 (2001-09) / EN 301 489-17 V.1.1.1 (2000-09)
 EN 50371: 2002
 EN 60950: 2000
www.voipon.co.uk [email protected] Tel:[phone] Fax: [phone]

2
FCC RF EXPOSURE COMPLIANCE
This PCS phone has been tested and complies with the Federal
Communications Commission (FCC) RF exposure limits for the General
Population/Uncontrolled exposure environment. In addition, it complies with
the following Standards and Guidelines:
 FCC 96-326, Guidelines for Evaluating the Environmental Effects of
Radio-Frequency Radiation
 FCC OET Bulletin 65 Edition 01-01 (2001) Supplement C, Evaluating
Compliance with FCC Guidelines for Human Exposure to Radio
Frequency Electromagnetic Fields
 ANSI/IEEE C95.1-1992, IEEE Standard for Safety Levels with Respect
to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz
to 300 GHz
 ANSI/IEEE C95.3-1992, IEEE Recommended Practice for the
Measurement of Potentially Hazardous Electromagnetic Fields - RF and
Microwave
 Note: For body-worn operation, this phone has been tested and
meets FCC RF exposure guidelines when used with an accessory
that contains no metal and when the back of the phone faces your
body.
 Use of other accessories may not ensure compliance with FCC RF
exposure guidelines.
www.voipon.co.uk [email protected] Tel:[phone] Fax: [phone]

3
1. BASIC OPERATIONS
1.1 Switch the Phone On/Off
Press and hold the power key to switch the phone on/off.
If the PowerOn Code function is active, after switching on the phone, enter
the security code and press the left soft key (Ok).
1.2 Access Menu/Names Options
1. In standby mode, press the left soft key (Menu) or the right soft key
(Names).
2. Press to reach the desired submenu, and then press the left soft
key (OK).
3. Repeat step 2 to reach the desired option.
 Note: To return to the previous menu level, press the right soft key
(Exit). To return to standby mode without changing the menu
settings, press .
1.3 Make a Call
1. Key in the phone number, or access Search and highlight the
desired phone number.
2. Press to call the number.
3. To end the ongoing call, press the right soft key (Hangup) or the
key.
 Note: Prior to making or receiving calls, the phone must be
connected to a wireless Access Point (AP) and registered with the
service network.
www.voipon.co.uk [email protected] Tel:[phone] Fax: [phone]

4
1.4 Use Speed Dial
If you have assigned a phone number to one of the speed dial keys ~
, you can quickly call that phone number:
1. In standby mode, press and hold the corresponding speed dial key to
automatically display the phone number.
2. Press to call the number.
1.5 Answer/Reject a Call
 To answer a call, press the left soft key (Answer) or the key
 To reject a call, press the right soft key (Hangup) or the key
 To stop the vibration or ring alert without picking up the incoming call,
press
1.6 Call Waiting
If the Call Waiting function is activated, when another call comes in during a
call, the earpiece will sound a waiting tone.
 To reject the incoming third party call and continue the current call,
press the right soft key (Hangup)
 To hold the current call and answer the incoming third party call, press
the left soft key (Answer)
1.7 In Call Operations
While on a call, you can perform the following operations:
 Press to increase or to decrease the listening volume
 Press to access the phonebook entry list (if the phonebook is not
empty)
www.voipon.co.uk [email protected] Tel:[phone] Fax: [phone]

5
 Press the left soft key (Option) and select from the following
options:
- Hold or Unhold: To take the call on/off hold
- New Call: To make a third party call
- Conference: To make a conference call (available only when the
Three Way Call function is active)
- Blind or Consult: To transfer the ongoing received call
- Mute: To mute the microphone volume
1.8 Keypad Lock
In standby mode, press and hold to lock the keypad. The indicator
will be displayed. To unlock the keypad, press and hold again.
2. PHONEBOOK (NAMES)
2.1 Add Phonebook Entries
You can add phone book entries in either of the following ways:
 In standby mode, key in the phone number and press the left soft key
(Save). Follow the prompts to enter the name and select the group
 Access Add Entry. Follow the prompts to enter the name and
phone number, and select the group
2.2 Search Phonebook Entries
In the phonebook entry list, press ~ to enter the first
letter(s)/digit(s) of the desired entry (name). A maximum of six letters/digits
can be entered. All names starting with these letter(s)/digit(s) will be
displayed.
www.voipon.co.uk [email protected] Tel:[phone] Fax: [phone]

6
2.3 Assign Phone Numbers to Speed Dial Keys
Access Speed Dial, press to select the desired speed dial
key. Press the left soft key (Set) to display the phonebook entry list.
Highlight the desired entry and press the left soft key (Ok) to assign the
number to the key.
3. MENU
In standby mode, press the left soft key (Menu) to access the menu.
The following submenus are available:
3.1 Call Log
Call Log
This submenu enables you to view missed call log (Missed Log), received
call log (Received Log) and outgoing call log (Dialed Log).
3.2 Profiles
Profiles
This submenu enables you to customize the phone alert settings to suit a
variety of environments. You can set the Ring Volume, Ring Mode, Ring
Tone, Alarm Tone, Keypad Tone and Alert Tone for a profile.
3.3 Settings
Settings
From this submenu, you can perform various phone settings, including:
Scheme, Date/Time, Answer Mode, Language, Display and Set
Security.
www.voipon.co.uk [email protected] Tel:[phone] Fax: [phone]

7
3.4 Tools
Tools
From this submenu, you can use the Calculator, view the Calendar, set
the Alarm, change the current Time Zone, perform DST Setting or set the
Time Format.
3.5 WiFi-Settings
WiFi-Settings
From this submenu, you can perform the following WiFi settings, including
Net Search, WiFi Config, Network Parameter and Signal Protocol.
 Note: After completing WiFi settings, switch the phone off and then
on, to apply the changed WiFi settings.
3.5.1 Net Search
WiFi-SettingsNet Search
This option enables you to search available APs for the phone. APs can be
defined and saved using the Net Search feature if APs have broadcast
turned on and the phone is within their ranges.
3.5.2 WiFi Config
3.5.2.1 AP Profile
WiFi-SettingsWiFi ConfigAP Profile
This option enables you to set up to four AP (Access Point) profiles. Each
time you switch on the phone, the phone will try to connect to one of these
APs according to their respective profile settings.
After you select this option, the AP profile list will be displayed. If the
security mode of an AP profile is set to WEP Key, the icon will be
displayed in front of the AP profile. If the security mode is set to WPA-PSK,
the icon will be displayed in front of the AP profile. If the security mode
is set to Open AP, no icon will be displayed in front of the AP profile.
www.voipon.co.uk [email protected] Tel:[phone] Fax: [phone]

8
Press to highlight the desired AP profile, and then press the left soft
key (Ok). The following options will be available:
SSID
This option enables you to save an AP’s SSID to the AP profile.
After accessing this option, enter the SSID (32 alphanumeric characters
maximum), and then press the left soft key (Ok) to complete the
operation.
Security Mode
This option enables you to set the security mode for the AP profile.
After accessing this option, select Open AP, WEP Key or WPA-PSK:
 If WEP Key is selected, the phone will then display the options of WEP
Key Info (refer to “WEP Key Info”)
 If WPA-PSK is selected, the phone will then display the PSK-editing
screen (refer to “WPA-PSK Info”)
WEP Key Info
If the AP profile’s security mode is set to WEP Key, select this option to set
the WEP key.After accessing this option, observe the following operations:
1. Select Auth Method, and then select the authentication method: Open
Key or Shared Key.
2. Select 64bit or 128bit according to the AP’s WEP key setting. Enter the
WEP key that the AP used, and press the left soft key (Ok).
- If 64bit is selected, ensure that the WEP key consists of five ASCII
characters or ten hexadecimal characters
- If 128bit is selected, ensure that the WEP key consists of 13 ASCII
characters or 26 hexadecimal characters
3. Select WEP Key Index. Enter the WEP key index (1-4), and then press
the left soft key (Ok).
www.voipon.co.uk [email protected] Tel:[phone] Fax: [phone]

9
 Note: The WEP key setting may be different due to AP settings.
If an AP supports only a fixed hexadecimal WEP key, you should
enter the same WEP key in the phone.
If an AP supports both ASCII and hexadecimal WEP keys, you can
enter either the ACSII WEP key or the hexadecimal WEP key in the
phone.
WPA-PSK Info
If the AP profile’s security mode is set to WPA-PSK, select this option to set
the WPA-PSK key.
After accessing this option, enter the WPA-PSK key and press the left soft
key (Ok) to complete the operation.
 Ensure that the WPA-PSK key consists of 8-63 ASCII characters or 64
hexadecimal characters
Activate
Select this option to connect to the AP according to the AP profile setting. If
the connection fails, the phone will try to connect to other AP profiles’APs. If
the phone fails to connect to all these APs and the Auto Scan function is
active, the phone will try to search and connect to another available open
AP. (Refer to “Auto Scan”)
3.5.2.2 Auto Scan
WiFi-SettingsWiFi ConfigAuto Scan
If the Auto Scan function is active, when the phone is switched on and fails
to connect to the APs specified in “AP Profile”, the phone will do a scan for
available APs and try to connect to one open AP of these scanned APs.
After accessing this option, select Enable or Disable to activate or
deactivate the Auto Scan function.
 Note: If the phone fails to connect to all the specified and scanned
APs, the phone will periodically retry AP connections.
 If the phone fails to register with the Vonage network after the AP
www.voipon.co.uk [email protected] Tel:[phone] Fax: [phone]

10
connection, the phone will prompt you to try another AP.
3.5.3 Network Parameter
3.5.3.1 DHCP
WiFi-SettingsNetwork ParameterDHCP
After accessing this option, select Disable or Enable to disable or enable
DHCP.
3.5.3.2 IP
WiFi-SettingsNetwork ParameterIP
This option enables you to perform IP settings. Select IP Address, Subnet
Mask or Gateway IP Address; key in the IP address, subnet mask or
gateway IP address; press the left soft key (Ok) to complete the
operation.
3.5.3.3 DNS
WiFi-SettingsNetwork ParameterDNS
This option enables you to perform DNS settings, including Primary DNS
Server IP Address, Secondary DNS Server IP Address and Priority.
3.5.3.4 Network Information
WiFi-SettingsNetwork ParameterNetwork Information
Select this option to view the network information.
3.6 Network Service
Network Service
From this submenu, you can set network services, including Call Waiting,
Call Transfer, Three Way Call, Register Interval Time, Caller-ID Block,
Repeat Dial on Busy, Reject Anonymous Incoming Call and Personal
www.voipon.co.uk [email protected] Tel:[phone] Fax: [phone]