V-tech VSMART VS014 User manual

Important safety instructions
When using your equipment, basic safety
precautions should always be followed to reduce the
risk of fire, electric shock and injury, including the
following:
1. Adult setup is required.
2. Do not place this product on unstable shelves,
stands, tables or other surfaces.
3. Children should be supervised to ensure that
they do not play with the product.
4. The product is not intended for use by persons
(including children) with reduced physical,
extension or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance by a
person responsible for their safety.
5. Do not use the motion extension ringer in the
following areas that may cause deformation,
malfunction, or operational failure:
• under direct sunlight;
• areas exposed to grease or steam, such as
kitchens;
• near fire or heating devices;
• areas subject to extreme temperature
changes, such as next to air conditioners;
• areas with IR-opaque or reflective objects
that can block IR energy that are needed for
detection;
• areas where the temperature is affected by
strong illuminating objects (such as halogen
lights).
SAVE THESE INSTRUCTIONS
Battery
• CAUTION: Use only the battery indicated in this
manual. There may be a risk of explosion if a
wrong type of battery is used for the extension
ringer unit.
• Do not dispose of the battery in a fire. Check
with local waste management codes for special
disposal instructions.
• Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause burns or
injury to the eyes or skin. The electrolyte may be
toxic if swallowed.
• Exercise care in handling battery in order not to
create a short circuit with conductive materials.
What’s in the box
Your product package contains the following
items. Save your sales receipt and original
packaging in the event warranty service is
necessary.
Extension ringer overview
1
2
3
4
5
1 – Pair button
• Press and hold to register the Extension
ringer to the telephone base.
2 – Power jack
3 – LED lights
• Red light on when there is no backup
batteries installed or the backup batteries
are low.
• Green light on when powered on, or
green light flashes while registering to the
telephone base.
• Blue light on while checking signal
strength.
4 – Loud speaker
5 – Visual ringer indicator (white LED)
• Flashes when receiving an incoming call
or when a reminder alarm set with your
telephone system goes off.
7
8
6
9
10
6 – Ringer volume
• Slide the switch to adjust
the ringer volume.
7 – Alert modes
• The Extension ringer’s LED flashes and/
or the ringer plays a melody when:
- There is an incoming call; or
- A reminder alarm set with your
telephone system goes off; or
- The audio doorbell (purchased
separately) rings.
• Slide the switch to change the alert
mode between:
Flash only
- Only the LED light flashes.
Play melody only
- The ringer only plays a melody.
Flash and play melody
- The ringer plays a melody and the LED
light flashes.
Turn off both flash and melody
- Disable the alert. The ringer does not play
melody and the LED light does not flash.
8 – Melodies
• Slide the switch to change between the
three melodies.
9 – Battery compartment cover
• Insert 3 AA alkaline batteries as power
backup (optional).
10 – Wall mounting holes
User’s manual
Extension Ringer Power adaptor
VS014
Extension Ringer
for use with compatible
VTech telephone system
For product support
please call: 1 300 369 193
Low
Medium
High

Important safety instructions
When using your equipment, basic safety
precautions should always be followed to reduce the
risk of fire, electric shock and injury, including the
following:
1. Adult setup is required.
2. Do not place this product on unstable shelves,
stands, tables or other surfaces.
3. Children should be supervised to ensure that
they do not play with the product.
4. The product is not intended for use by persons
(including children) with reduced physical,
extension or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance by a
person responsible for their safety.
5. Do not use the motion extension ringer in the
following areas that may cause deformation,
malfunction, or operational failure:
• under direct sunlight;
• areas exposed to grease or steam, such as
kitchens;
• near fire or heating devices;
• areas subject to extreme temperature
changes, such as next to air conditioners;
• areas with IR-opaque or reflective objects
that can block IR energy that are needed for
detection;
• areas where the temperature is affected by
strong illuminating objects (such as halogen
lights).
SAVE THESE INSTRUCTIONS
Battery
• CAUTION: Use only the battery indicated in this
manual. There may be a risk of explosion if a
wrong type of battery is used for the extension
ringer unit.
• Do not dispose of the battery in a fire. Check
with local waste management codes for special
disposal instructions.
• Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause burns or
injury to the eyes or skin. The electrolyte may be
toxic if swallowed.
• Exercise care in handling battery in order not to
create a short circuit with conductive materials.
What’s in the box
Your product package contains the following
items. Save your sales receipt and original
packaging in the event warranty service is
necessary.
Extension ringer overview
1
2
3
4
5
1 – Pair button
• Press and hold to register the Extension
ringer to the telephone base.
2 – Power jack
3 – LED lights
• Red light on when there is no backup
batteries installed or the backup batteries
are low.
• Green light on when powered on, or
green light flashes while registering to the
telephone base.
• Blue light on while checking signal
strength.
4 – Loud speaker
5 – Visual ringer indicator (white LED)
• Flashes when receiving an incoming call
or when a reminder alarm set with your
telephone system goes off.
7
8
6
9
10
6 – Ringer volume
• Slide the switch to adjust
the ringer volume.
7 – Alert modes
• The Extension ringer’s LED flashes and/
or the ringer plays a melody when:
- There is an incoming call; or
- A reminder alarm set with your
telephone system goes off; or
- The audio doorbell (purchased
separately) rings.
• Slide the switch to change the alert
mode between:
Flash only
- Only the LED light flashes.
Play melody only
- The ringer only plays a melody.
Flash and play melody
- The ringer plays a melody and the LED
light flashes.
Turn off both flash and melody
- Disable the alert. The ringer does not play
melody and the LED light does not flash.
8 – Melodies
• Slide the switch to change between the
three melodies.
9 – Battery compartment cover
• Insert 3 AA alkaline batteries as power
backup (optional).
10 – Wall mounting holes
User’s manual
Extension Ringer Power adaptor
VS014
Extension Ringer
for use with compatible
VTech telephone system
For product support
please call: 1 300 369 193
Low
Medium
High

Important safety instructions
When using your equipment, basic safety
precautions should always be followed to reduce the
risk of fire, electric shock and injury, including the
following:
1. Adult setup is required.
2. Do not place this product on unstable shelves,
stands, tables or other surfaces.
3. Children should be supervised to ensure that
they do not play with the product.
4. The product is not intended for use by persons
(including children) with reduced physical,
extension or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance by a
person responsible for their safety.
5. Do not use the motion extension ringer in the
following areas that may cause deformation,
malfunction, or operational failure:
• under direct sunlight;
• areas exposed to grease or steam, such as
kitchens;
• near fire or heating devices;
• areas subject to extreme temperature
changes, such as next to air conditioners;
• areas with IR-opaque or reflective objects
that can block IR energy that are needed for
detection;
• areas where the temperature is affected by
strong illuminating objects (such as halogen
lights).
SAVE THESE INSTRUCTIONS
Battery
• CAUTION: Use only the battery indicated in this
manual. There may be a risk of explosion if a
wrong type of battery is used for the extension
ringer unit.
• Do not dispose of the battery in a fire. Check
with local waste management codes for special
disposal instructions.
• Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause burns or
injury to the eyes or skin. The electrolyte may be
toxic if swallowed.
• Exercise care in handling battery in order not to
create a short circuit with conductive materials.
What’s in the box
Your product package contains the following
items. Save your sales receipt and original
packaging in the event warranty service is
necessary.
Extension ringer overview
1
2
3
4
5
1 – Pair button
• Press and hold to register the Extension
ringer to the telephone base.
2 – Power jack
3 – LED lights
• Red light on when there is no backup
batteries installed or the backup batteries
are low.
• Green light on when powered on, or
green light flashes while registering to the
telephone base.
• Blue light on while checking signal
strength.
4 – Loud speaker
5 – Visual ringer indicator (white LED)
• Flashes when receiving an incoming call
or when a reminder alarm set with your
telephone system goes off.
7
8
6
9
10
6 – Ringer volume
• Slide the switch to adjust
the ringer volume.
7 – Alert modes
• The Extension ringer’s LED flashes and/
or the ringer plays a melody when:
- There is an incoming call; or
- A reminder alarm set with your
telephone system goes off; or
- The audio doorbell (purchased
separately) rings.
• Slide the switch to change the alert
mode between:
Flash only
- Only the LED light flashes.
Play melody only
- The ringer only plays a melody.
Flash and play melody
- The ringer plays a melody and the LED
light flashes.
Turn off both flash and melody
- Disable the alert. The ringer does not play
melody and the LED light does not flash.
8 – Melodies
• Slide the switch to change between the
three melodies.
9 – Battery compartment cover
• Insert 3 AA alkaline batteries as power
backup (optional).
10 – Wall mounting holes
User’s manual
Extension Ringer Power adaptor
VS014
Extension Ringer
for use with compatible
VTech telephone system
For product support
please call: 1 300 369 193
Low
Medium
High

Important safety instructions
When using your equipment, basic safety
precautions should always be followed to reduce the
risk of fire, electric shock and injury, including the
following:
1. Adult setup is required.
2. Do not place this product on unstable shelves,
stands, tables or other surfaces.
3. Children should be supervised to ensure that
they do not play with the product.
4. The product is not intended for use by persons
(including children) with reduced physical,
extension or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance by a
person responsible for their safety.
5. Do not use the motion extension ringer in the
following areas that may cause deformation,
malfunction, or operational failure:
• under direct sunlight;
• areas exposed to grease or steam, such as
kitchens;
• near fire or heating devices;
• areas subject to extreme temperature
changes, such as next to air conditioners;
• areas with IR-opaque or reflective objects
that can block IR energy that are needed for
detection;
• areas where the temperature is affected by
strong illuminating objects (such as halogen
lights).
SAVE THESE INSTRUCTIONS
Battery
• CAUTION: Use only the battery indicated in this
manual. There may be a risk of explosion if a
wrong type of battery is used for the extension
ringer unit.
• Do not dispose of the battery in a fire. Check
with local waste management codes for special
disposal instructions.
• Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause burns or
injury to the eyes or skin. The electrolyte may be
toxic if swallowed.
• Exercise care in handling battery in order not to
create a short circuit with conductive materials.
What’s in the box
Your product package contains the following
items. Save your sales receipt and original
packaging in the event warranty service is
necessary.
Extension ringer overview
1
2
3
4
5
1 – Pair button
• Press and hold to register the Extension
ringer to the telephone base.
2 – Power jack
3 – LED lights
• Red light on when there is no backup
batteries installed or the backup batteries
are low.
• Green light on when powered on, or
green light flashes while registering to the
telephone base.
• Blue light on while checking signal
strength.
4 – Loud speaker
5 – Visual ringer indicator (white LED)
• Flashes when receiving an incoming call
or when a reminder alarm set with your
telephone system goes off.
7
8
6
9
10
6 – Ringer volume
• Slide the switch to adjust
the ringer volume.
7 – Alert modes
• The Extension ringer’s LED flashes and/
or the ringer plays a melody when:
- There is an incoming call; or
- A reminder alarm set with your
telephone system goes off; or
- The audio doorbell (purchased
separately) rings.
• Slide the switch to change the alert
mode between:
Flash only
- Only the LED light flashes.
Play melody only
- The ringer only plays a melody.
Flash and play melody
- The ringer plays a melody and the LED
light flashes.
Turn off both flash and melody
- Disable the alert. The ringer does not play
melody and the LED light does not flash.
8 – Melodies
• Slide the switch to change between the
three melodies.
9 – Battery compartment cover
• Insert 3 AA alkaline batteries as power
backup (optional).
10 – Wall mounting holes
User’s manual
Extension Ringer Power adaptor
VS014
Extension Ringer
for use with compatible
VTech telephone system
For product support
please call: 1 300 369 193
Low
Medium
High

Important safety instructions
When using your equipment, basic safety
precautions should always be followed to reduce the
risk of fire, electric shock and injury, including the
following:
1. Adult setup is required.
2. Do not place this product on unstable shelves,
stands, tables or other surfaces.
3. Children should be supervised to ensure that
they do not play with the product.
4. The product is not intended for use by persons
(including children) with reduced physical,
extension or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance by a
person responsible for their safety.
5. Do not use the motion extension ringer in the
following areas that may cause deformation,
malfunction, or operational failure:
• under direct sunlight;
• areas exposed to grease or steam, such as
kitchens;
• near fire or heating devices;
• areas subject to extreme temperature
changes, such as next to air conditioners;
• areas with IR-opaque or reflective objects
that can block IR energy that are needed for
detection;
• areas where the temperature is affected by
strong illuminating objects (such as halogen
lights).
SAVE THESE INSTRUCTIONS
Battery
• CAUTION: Use only the battery indicated in this
manual. There may be a risk of explosion if a
wrong type of battery is used for the extension
ringer unit.
• Do not dispose of the battery in a fire. Check
with local waste management codes for special
disposal instructions.
• Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause burns or
injury to the eyes or skin. The electrolyte may be
toxic if swallowed.
• Exercise care in handling battery in order not to
create a short circuit with conductive materials.
What’s in the box
Your product package contains the following
items. Save your sales receipt and original
packaging in the event warranty service is
necessary.
Extension ringer overview
1
2
3
4
5
1 – Pair button
• Press and hold to register the Extension
ringer to the telephone base.
2 – Power jack
3 – LED lights
• Red light on when there is no backup
batteries installed or the backup batteries
are low.
• Green light on when powered on, or
green light flashes while registering to the
telephone base.
• Blue light on while checking signal
strength.
4 – Loud speaker
5 – Visual ringer indicator (white LED)
• Flashes when receiving an incoming call
or when a reminder alarm set with your
telephone system goes off.
7
8
6
9
10
6 – Ringer volume
• Slide the switch to adjust
the ringer volume.
7 – Alert modes
• The Extension ringer’s LED flashes and/
or the ringer plays a melody when:
- There is an incoming call; or
- A reminder alarm set with your
telephone system goes off; or
- The audio doorbell (purchased
separately) rings.
• Slide the switch to change the alert
mode between:
Flash only
- Only the LED light flashes.
Play melody only
- The ringer only plays a melody.
Flash and play melody
- The ringer plays a melody and the LED
light flashes.
Turn off both flash and melody
- Disable the alert. The ringer does not play
melody and the LED light does not flash.
8 – Melodies
• Slide the switch to change between the
three melodies.
9 – Battery compartment cover
• Insert 3 AA alkaline batteries as power
backup (optional).
10 – Wall mounting holes
User’s manual
Extension Ringer Power adaptor
VS014
Extension Ringer
for use with compatible
VTech telephone system
For product support
please call: 1 300 369 193
Low
Medium
High

Before use
Power on the extension ringer
Option 1 - Connect to the power supply
• Plug the small end of power adapter to the
power jack on the extension ringer, and the
large end to wall jack.
Option 2 - Insert AA batteries
(purchased separately)
• Match the polarity markings (+ and -) inside
the battery compartment.
Add and register a extension ringer
Add your new VS014 extension ringer to your
telephone base. Each new extension ringer
must be registered with the telephone base
before use.
Register a extension ringer:
1. Make sure the extension ringer is powered
on with batteries or DC power before
registering it to the telephone base.
2. Place your telephone base into pairing
mode as per the instructions in your
telephone user guide.
3. Press and hold the pair button on the
back of the extension ringer until the
white Flash LED light flashes. The
Extension ringer is now registering to the
telephone base.
Replacing a extension ringer
If you have purchased this new VS014 accessory
extension ringer to replace an old extension
ringer, you must deregister the registered
extension ringer first, and then register this new
extension ringer to your telephone base.
Deregister a extension ringer or all
extension ringers:
• Refer to the User’s manual of your
telephone system to deregister a extension
ringer or all extension ringers.
General product care
Taking care of your extension ringer
Your extension ringer contains sophisticated
electronic and optical parts, so it must be treated
with care.
Avoid rough treatment
Place the extension ringer down gently. Save the
original packing materials to protect your extension
ringer if you ever need to ship it.
Avoid water
Your extension ringer can be damaged if it gets
wet. Do not use the extension ringer outdoors in the
rain, or handle it with wet hands. Do not install the
extension ringer near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power
surges harmful to electronic equipment. For your
own safety, take caution when using electrical
appliances during storms.
Cleaning your extension ringer
Your extension ringer has a durable plastic casing
that should retain its luster for many years. Clean it
only with a dry non-abrasive cloth. Do not use
dampened cloth or cleaning solvents of any kind.
Storage
When you are not going to use the extension
ringer for some time, remove the battery from the
extension ringer. Store the extension ringer in a
cool and dry place.
Frequently asked questions
Below are the questions most frequently asked
about the extension ringer.
The
extension
ringer
doesn’t work
with the
telephone
system
equipment.
• Make sure the unit is connected
to the power supply, or with the
AA alkaline batteries installed.
• The extension ringer may
be deregistered from your
telephone system. Refer to
Add and register a extension
ringer and register the
extension ringer back.
• The extension ringer may be out
of range. Move the extension
ringer closer to your telephone
system.
• If the previous suggestions
do not work, deregister all
devices and register them to the
telephone base again.
Technical specifications
Frequency
control
Crystal controlled PLL
synthesizer
Transmit
frequency
1881.792 MHz - 1897.344 MHz
Channels 10
Nominal
effective range
Actual operating range may
vary according to environment
conditions at the time of use.
Power adaptor Model: S003IV0600045
Input: 100-240V~ 50/60Hz 150mA
Output: 6V 450mA
Battery 3 x AA Alkaline battery
Disclaimer
This product is not designed for security purposes.
When properly installed and maintained, this
product may in some cases reduce the risk of
burglary, fire, robbery or other events occurring
without providing an alarm. VTech is not responsible
for losses, injury, or damage resulting from the use
of this product.
Customer service &
Product warranty
IMPORTANT
Please retain this booklet with your sales receipt as
proof of the date of purchase.
Customer Service
If you require assistance in operating this product
please call the TecHelp Information Line on
1300 369 193 or contact VTech by e-mail at:
tcpsuppor[email protected].
If you are trying to access a Telephone Network
Service and require assistance specifically related
to the network service or would like to subscribe to
the service, contact your service provider.
Voluntary Product Warranty
In addition to your Statutory Rights and subject
to the conditions below, VTech warrants that this
product will be free from any defect in materials or
workmanship under conditions of normal use for a
period of 12 months from date of purchase.
VTech do not warrant that the product will be free
from defects if defects are caused by an accident,
misuse, abuse, improper installation or operation,
vermin infestations, lack of reasonable care,
unauthorised modification, loss of parts, tampering
or attempted repair by a person not authorised by
VTech; or where the product has been damaged by
lightning or a mains power surge.
Where a valid claim is made under this Voluntary
Product Warranty, VTech will, at no cost to you,
repair or replace the product within a reasonable
time. Subject to your Statutory Rights, if your claim
under this Voluntary Product Warranty is not valid,
you may be charged a fee under this Voluntary
Product Warranty for the service and for any direct
costs associated with having the product delivered
for service.
To make a claim under this Voluntary Product
Warranty you must call the TecHelp Information
Line on 1300 369 193 or contact VTech by e-mail
at: tcpsuppor[email protected] where a Customer
Service Representative will inform you of the product
return process. You will need to ensure that:
You provide proof of purchase;
Your product is suitably packaged (original
packaging is not required); and
You have included all components from the original
purchase.
For your records
Date of purchase:
_______________________________
Place of purchase:
_______________________________
Serial number:
_______________________________
For Voluntary Product Warranty purposes proof of
purchase is required so please keep your receipt.
The benefits conferred by this Voluntary Product
Warranty are in addition to other rights and remedies
that are available to you under law, which cannot be
excluded. The processes for this Voluntary Product
Warranty in no way limit your rights which arise as a
result of your Statutory Rights.
This Voluntary Product Warranty is given by:
VTech Telecommunications (Australia) Pty Ltd ABN
70 136 672 627
Address: 24 Gilby Road, Mount Waverley 3149
IMPORTANT NOTE: THIS IS NOT A PRODUCT
RETURN OR SERVICE ADDRESS – PLEASE
CONTACT TECHELP BY PHONE OR EMAIL
FOR PRODUCT AND WARRANTY SUPPORT.
NO LIABILITY WILL BE ACCEPTED BY
VTECH FOR PRODUCTS RETURNED TO THIS
ADDRESS UNDER THIS VOLUNTARY PRODUCT
WARRANTY.
Phone number: 1300 369 193
Email address: [e-mail]
Statutory Rights
Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You
are entitled to a replacement or refund for a major
failure and compensation for any other reasonably
foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not
amount to a major failure.
Vtech Telecommunications (Australia) Pty Ltd.
A member of THE VTECH GROUP OF COMPANIES.
VTech is a registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
© 2018 VTech Telecommunications (Australia).
All rights reserved. Version 2 08/18.
1
1
2
3

Before use
Power on the extension ringer
Option 1 - Connect to the power supply
• Plug the small end of power adapter to the
power jack on the extension ringer, and the
large end to wall jack.
Option 2 - Insert AA batteries
(purchased separately)
• Match the polarity markings (+ and -) inside
the battery compartment.
Add and register a extension ringer
Add your new VS014 extension ringer to your
telephone base. Each new extension ringer
must be registered with the telephone base
before use.
Register a extension ringer:
1. Make sure the extension ringer is powered
on with batteries or DC power before
registering it to the telephone base.
2. Place your telephone base into pairing
mode as per the instructions in your
telephone user guide.
3. Press and hold the pair button on the
back of the extension ringer until the
white Flash LED light flashes. The
Extension ringer is now registering to the
telephone base.
Replacing a extension ringer
If you have purchased this new VS014 accessory
extension ringer to replace an old extension
ringer, you must deregister the registered
extension ringer first, and then register this new
extension ringer to your telephone base.
Deregister a extension ringer or all
extension ringers:
• Refer to the User’s manual of your
telephone system to deregister a extension
ringer or all extension ringers.
General product care
Taking care of your extension ringer
Your extension ringer contains sophisticated
electronic and optical parts, so it must be treated
with care.
Avoid rough treatment
Place the extension ringer down gently. Save the
original packing materials to protect your extension
ringer if you ever need to ship it.
Avoid water
Your extension ringer can be damaged if it gets
wet. Do not use the extension ringer outdoors in the
rain, or handle it with wet hands. Do not install the
extension ringer near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power
surges harmful to electronic equipment. For your
own safety, take caution when using electrical
appliances during storms.
Cleaning your extension ringer
Your extension ringer has a durable plastic casing
that should retain its luster for many years. Clean it
only with a dry non-abrasive cloth. Do not use
dampened cloth or cleaning solvents of any kind.
Storage
When you are not going to use the extension
ringer for some time, remove the battery from the
extension ringer. Store the extension ringer in a
cool and dry place.
Frequently asked questions
Below are the questions most frequently asked
about the extension ringer.
The
extension
ringer
doesn’t work
with the
telephone
system
equipment.
• Make sure the unit is connected
to the power supply, or with the
AA alkaline batteries installed.
• The extension ringer may
be deregistered from your
telephone system. Refer to
Add and register a extension
ringer and register the
extension ringer back.
• The extension ringer may be out
of range. Move the extension
ringer closer to your telephone
system.
• If the previous suggestions
do not work, deregister all
devices and register them to the
telephone base again.
Technical specifications
Frequency
control
Crystal controlled PLL
synthesizer
Transmit
frequency
1881.792 MHz - 1897.344 MHz
Channels 10
Nominal
effective range
Actual operating range may
vary according to environment
conditions at the time of use.
Power adaptor Model: S003IV0600045
Input: 100-240V~ 50/60Hz 150mA
Output: 6V 450mA
Battery 3 x AA Alkaline battery
Disclaimer
This product is not designed for security purposes.
When properly installed and maintained, this
product may in some cases reduce the risk of
burglary, fire, robbery or other events occurring
without providing an alarm. VTech is not responsible
for losses, injury, or damage resulting from the use
of this product.
Customer service &
Product warranty
IMPORTANT
Please retain this booklet with your sales receipt as
proof of the date of purchase.
Customer Service
If you require assistance in operating this product
please call the TecHelp Information Line on
1300 369 193 or contact VTech by e-mail at:
tcpsuppor[email protected].
If you are trying to access a Telephone Network
Service and require assistance specifically related
to the network service or would like to subscribe to
the service, contact your service provider.
Voluntary Product Warranty
In addition to your Statutory Rights and subject
to the conditions below, VTech warrants that this
product will be free from any defect in materials or
workmanship under conditions of normal use for a
period of 12 months from date of purchase.
VTech do not warrant that the product will be free
from defects if defects are caused by an accident,
misuse, abuse, improper installation or operation,
vermin infestations, lack of reasonable care,
unauthorised modification, loss of parts, tampering
or attempted repair by a person not authorised by
VTech; or where the product has been damaged by
lightning or a mains power surge.
Where a valid claim is made under this Voluntary
Product Warranty, VTech will, at no cost to you,
repair or replace the product within a reasonable
time. Subject to your Statutory Rights, if your claim
under this Voluntary Product Warranty is not valid,
you may be charged a fee under this Voluntary
Product Warranty for the service and for any direct
costs associated with having the product delivered
for service.
To make a claim under this Voluntary Product
Warranty you must call the TecHelp Information
Line on 1300 369 193 or contact VTech by e-mail
at: tcpsuppor[email protected] where a Customer
Service Representative will inform you of the product
return process. You will need to ensure that:
You provide proof of purchase;
Your product is suitably packaged (original
packaging is not required); and
You have included all components from the original
purchase.
For your records
Date of purchase:
_______________________________
Place of purchase:
_______________________________
Serial number:
_______________________________
For Voluntary Product Warranty purposes proof of
purchase is required so please keep your receipt.
The benefits conferred by this Voluntary Product
Warranty are in addition to other rights and remedies
that are available to you under law, which cannot be
excluded. The processes for this Voluntary Product
Warranty in no way limit your rights which arise as a
result of your Statutory Rights.
This Voluntary Product Warranty is given by:
VTech Telecommunications (Australia) Pty Ltd ABN
70 136 672 627
Address: 24 Gilby Road, Mount Waverley 3149
IMPORTANT NOTE: THIS IS NOT A PRODUCT
RETURN OR SERVICE ADDRESS – PLEASE
CONTACT TECHELP BY PHONE OR EMAIL
FOR PRODUCT AND WARRANTY SUPPORT.
NO LIABILITY WILL BE ACCEPTED BY
VTECH FOR PRODUCTS RETURNED TO THIS
ADDRESS UNDER THIS VOLUNTARY PRODUCT
WARRANTY.
Phone number: 1300 369 193
Email address: [e-mail]
Statutory Rights
Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You
are entitled to a replacement or refund for a major
failure and compensation for any other reasonably
foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not
amount to a major failure.
Vtech Telecommunications (Australia) Pty Ltd.
A member of THE VTECH GROUP OF COMPANIES.
VTech is a registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
© 2018 VTech Telecommunications (Australia).
All rights reserved. Version 2 08/18.
1
1
2
3

Before use
Power on the extension ringer
Option 1 - Connect to the power supply
• Plug the small end of power adapter to the
power jack on the extension ringer, and the
large end to wall jack.
Option 2 - Insert AA batteries
(purchased separately)
• Match the polarity markings (+ and -) inside
the battery compartment.
Add and register a extension ringer
Add your new VS014 extension ringer to your
telephone base. Each new extension ringer
must be registered with the telephone base
before use.
Register a extension ringer:
1. Make sure the extension ringer is powered
on with batteries or DC power before
registering it to the telephone base.
2. Place your telephone base into pairing
mode as per the instructions in your
telephone user guide.
3. Press and hold the pair button on the
back of the extension ringer until the
white Flash LED light flashes. The
Extension ringer is now registering to the
telephone base.
Replacing a extension ringer
If you have purchased this new VS014 accessory
extension ringer to replace an old extension
ringer, you must deregister the registered
extension ringer first, and then register this new
extension ringer to your telephone base.
Deregister a extension ringer or all
extension ringers:
• Refer to the User’s manual of your
telephone system to deregister a extension
ringer or all extension ringers.
General product care
Taking care of your extension ringer
Your extension ringer contains sophisticated
electronic and optical parts, so it must be treated
with care.
Avoid rough treatment
Place the extension ringer down gently. Save the
original packing materials to protect your extension
ringer if you ever need to ship it.
Avoid water
Your extension ringer can be damaged if it gets
wet. Do not use the extension ringer outdoors in the
rain, or handle it with wet hands. Do not install the
extension ringer near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power
surges harmful to electronic equipment. For your
own safety, take caution when using electrical
appliances during storms.
Cleaning your extension ringer
Your extension ringer has a durable plastic casing
that should retain its luster for many years. Clean it
only with a dry non-abrasive cloth. Do not use
dampened cloth or cleaning solvents of any kind.
Storage
When you are not going to use the extension
ringer for some time, remove the battery from the
extension ringer. Store the extension ringer in a
cool and dry place.
Frequently asked questions
Below are the questions most frequently asked
about the extension ringer.
The
extension
ringer
doesn’t work
with the
telephone
system
equipment.
• Make sure the unit is connected
to the power supply, or with the
AA alkaline batteries installed.
• The extension ringer may
be deregistered from your
telephone system. Refer to
Add and register a extension
ringer and register the
extension ringer back.
• The extension ringer may be out
of range. Move the extension
ringer closer to your telephone
system.
• If the previous suggestions
do not work, deregister all
devices and register them to the
telephone base again.
Technical specifications
Frequency
control
Crystal controlled PLL
synthesizer
Transmit
frequency
1881.792 MHz - 1897.344 MHz
Channels 10
Nominal
effective range
Actual operating range may
vary according to environment
conditions at the time of use.
Power adaptor Model: S003IV0600045
Input: 100-240V~ 50/60Hz 150mA
Output: 6V 450mA
Battery 3 x AA Alkaline battery
Disclaimer
This product is not designed for security purposes.
When properly installed and maintained, this
product may in some cases reduce the risk of
burglary, fire, robbery or other events occurring
without providing an alarm. VTech is not responsible
for losses, injury, or damage resulting from the use
of this product.
Customer service &
Product warranty
IMPORTANT
Please retain this booklet with your sales receipt as
proof of the date of purchase.
Customer Service
If you require assistance in operating this product
please call the TecHelp Information Line on
1300 369 193 or contact VTech by e-mail at:
tcpsuppor[email protected].
If you are trying to access a Telephone Network
Service and require assistance specifically related
to the network service or would like to subscribe to
the service, contact your service provider.
Voluntary Product Warranty
In addition to your Statutory Rights and subject
to the conditions below, VTech warrants that this
product will be free from any defect in materials or
workmanship under conditions of normal use for a
period of 12 months from date of purchase.
VTech do not warrant that the product will be free
from defects if defects are caused by an accident,
misuse, abuse, improper installation or operation,
vermin infestations, lack of reasonable care,
unauthorised modification, loss of parts, tampering
or attempted repair by a person not authorised by
VTech; or where the product has been damaged by
lightning or a mains power surge.
Where a valid claim is made under this Voluntary
Product Warranty, VTech will, at no cost to you,
repair or replace the product within a reasonable
time. Subject to your Statutory Rights, if your claim
under this Voluntary Product Warranty is not valid,
you may be charged a fee under this Voluntary
Product Warranty for the service and for any direct
costs associated with having the product delivered
for service.
To make a claim under this Voluntary Product
Warranty you must call the TecHelp Information
Line on 1300 369 193 or contact VTech by e-mail
at: tcpsuppor[email protected] where a Customer
Service Representative will inform you of the product
return process. You will need to ensure that:
You provide proof of purchase;
Your product is suitably packaged (original
packaging is not required); and
You have included all components from the original
purchase.
For your records
Date of purchase:
_______________________________
Place of purchase:
_______________________________
Serial number:
_______________________________
For Voluntary Product Warranty purposes proof of
purchase is required so please keep your receipt.
The benefits conferred by this Voluntary Product
Warranty are in addition to other rights and remedies
that are available to you under law, which cannot be
excluded. The processes for this Voluntary Product
Warranty in no way limit your rights which arise as a
result of your Statutory Rights.
This Voluntary Product Warranty is given by:
VTech Telecommunications (Australia) Pty Ltd ABN
70 136 672 627
Address: 24 Gilby Road, Mount Waverley 3149
IMPORTANT NOTE: THIS IS NOT A PRODUCT
RETURN OR SERVICE ADDRESS – PLEASE
CONTACT TECHELP BY PHONE OR EMAIL
FOR PRODUCT AND WARRANTY SUPPORT.
NO LIABILITY WILL BE ACCEPTED BY
VTECH FOR PRODUCTS RETURNED TO THIS
ADDRESS UNDER THIS VOLUNTARY PRODUCT
WARRANTY.
Phone number: 1300 369 193
Email address: [e-mail]
Statutory Rights
Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You
are entitled to a replacement or refund for a major
failure and compensation for any other reasonably
foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not
amount to a major failure.
Vtech Telecommunications (Australia) Pty Ltd.
A member of THE VTECH GROUP OF COMPANIES.
VTech is a registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
© 2018 VTech Telecommunications (Australia).
All rights reserved. Version 2 08/18.
1
1
2
3

Before use
Power on the extension ringer
Option 1 - Connect to the power supply
• Plug the small end of power adapter to the
power jack on the extension ringer, and the
large end to wall jack.
Option 2 - Insert AA batteries
(purchased separately)
• Match the polarity markings (+ and -) inside
the battery compartment.
Add and register a extension ringer
Add your new VS014 extension ringer to your
telephone base. Each new extension ringer
must be registered with the telephone base
before use.
Register a extension ringer:
1. Make sure the extension ringer is powered
on with batteries or DC power before
registering it to the telephone base.
2. Place your telephone base into pairing
mode as per the instructions in your
telephone user guide.
3. Press and hold the pair button on the
back of the extension ringer until the
white Flash LED light flashes. The
Extension ringer is now registering to the
telephone base.
Replacing a extension ringer
If you have purchased this new VS014 accessory
extension ringer to replace an old extension
ringer, you must deregister the registered
extension ringer first, and then register this new
extension ringer to your telephone base.
Deregister a extension ringer or all
extension ringers:
• Refer to the User’s manual of your
telephone system to deregister a extension
ringer or all extension ringers.
General product care
Taking care of your extension ringer
Your extension ringer contains sophisticated
electronic and optical parts, so it must be treated
with care.
Avoid rough treatment
Place the extension ringer down gently. Save the
original packing materials to protect your extension
ringer if you ever need to ship it.
Avoid water
Your extension ringer can be damaged if it gets
wet. Do not use the extension ringer outdoors in the
rain, or handle it with wet hands. Do not install the
extension ringer near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power
surges harmful to electronic equipment. For your
own safety, take caution when using electrical
appliances during storms.
Cleaning your extension ringer
Your extension ringer has a durable plastic casing
that should retain its luster for many years. Clean it
only with a dry non-abrasive cloth. Do not use
dampened cloth or cleaning solvents of any kind.
Storage
When you are not going to use the extension
ringer for some time, remove the battery from the
extension ringer. Store the extension ringer in a
cool and dry place.
Frequently asked questions
Below are the questions most frequently asked
about the extension ringer.
The
extension
ringer
doesn’t work
with the
telephone
system
equipment.
• Make sure the unit is connected
to the power supply, or with the
AA alkaline batteries installed.
• The extension ringer may
be deregistered from your
telephone system. Refer to
Add and register a extension
ringer and register the
extension ringer back.
• The extension ringer may be out
of range. Move the extension
ringer closer to your telephone
system.
• If the previous suggestions
do not work, deregister all
devices and register them to the
telephone base again.
Technical specifications
Frequency
control
Crystal controlled PLL
synthesizer
Transmit
frequency
1881.792 MHz - 1897.344 MHz
Channels 10
Nominal
effective range
Actual operating range may
vary according to environment
conditions at the time of use.
Power adaptor Model: S003IV0600045
Input: 100-240V~ 50/60Hz 150mA
Output: 6V 450mA
Battery 3 x AA Alkaline battery
Disclaimer
This product is not designed for security purposes.
When properly installed and maintained, this
product may in some cases reduce the risk of
burglary, fire, robbery or other events occurring
without providing an alarm. VTech is not responsible
for losses, injury, or damage resulting from the use
of this product.
Customer service &
Product warranty
IMPORTANT
Please retain this booklet with your sales receipt as
proof of the date of purchase.
Customer Service
If you require assistance in operating this product
please call the TecHelp Information Line on
1300 369 193 or contact VTech by e-mail at:
tcpsuppor[email protected].
If you are trying to access a Telephone Network
Service and require assistance specifically related
to the network service or would like to subscribe to
the service, contact your service provider.
Voluntary Product Warranty
In addition to your Statutory Rights and subject
to the conditions below, VTech warrants that this
product will be free from any defect in materials or
workmanship under conditions of normal use for a
period of 12 months from date of purchase.
VTech do not warrant that the product will be free
from defects if defects are caused by an accident,
misuse, abuse, improper installation or operation,
vermin infestations, lack of reasonable care,
unauthorised modification, loss of parts, tampering
or attempted repair by a person not authorised by
VTech; or where the product has been damaged by
lightning or a mains power surge.
Where a valid claim is made under this Voluntary
Product Warranty, VTech will, at no cost to you,
repair or replace the product within a reasonable
time. Subject to your Statutory Rights, if your claim
under this Voluntary Product Warranty is not valid,
you may be charged a fee under this Voluntary
Product Warranty for the service and for any direct
costs associated with having the product delivered
for service.
To make a claim under this Voluntary Product
Warranty you must call the TecHelp Information
Line on 1300 369 193 or contact VTech by e-mail
at: tcpsuppor[email protected] where a Customer
Service Representative will inform you of the product
return process. You will need to ensure that:
You provide proof of purchase;
Your product is suitably packaged (original
packaging is not required); and
You have included all components from the original
purchase.
For your records
Date of purchase:
_______________________________
Place of purchase:
_______________________________
Serial number:
_______________________________
For Voluntary Product Warranty purposes proof of
purchase is required so please keep your receipt.
The benefits conferred by this Voluntary Product
Warranty are in addition to other rights and remedies
that are available to you under law, which cannot be
excluded. The processes for this Voluntary Product
Warranty in no way limit your rights which arise as a
result of your Statutory Rights.
This Voluntary Product Warranty is given by:
VTech Telecommunications (Australia) Pty Ltd ABN
70 136 672 627
Address: 24 Gilby Road, Mount Waverley 3149
IMPORTANT NOTE: THIS IS NOT A PRODUCT
RETURN OR SERVICE ADDRESS – PLEASE
CONTACT TECHELP BY PHONE OR EMAIL
FOR PRODUCT AND WARRANTY SUPPORT.
NO LIABILITY WILL BE ACCEPTED BY
VTECH FOR PRODUCTS RETURNED TO THIS
ADDRESS UNDER THIS VOLUNTARY PRODUCT
WARRANTY.
Phone number: 1300 369 193
Email address: [e-mail]
Statutory Rights
Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You
are entitled to a replacement or refund for a major
failure and compensation for any other reasonably
foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not
amount to a major failure.
Vtech Telecommunications (Australia) Pty Ltd.
A member of THE VTECH GROUP OF COMPANIES.
VTech is a registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
© 2018 VTech Telecommunications (Australia).
All rights reserved. Version 2 08/18.
1
1
2
3

Before use
Power on the extension ringer
Option 1 - Connect to the power supply
• Plug the small end of power adapter to the
power jack on the extension ringer, and the
large end to wall jack.
Option 2 - Insert AA batteries
(purchased separately)
• Match the polarity markings (+ and -) inside
the battery compartment.
Add and register a extension ringer
Add your new VS014 extension ringer to your
telephone base. Each new extension ringer
must be registered with the telephone base
before use.
Register a extension ringer:
1. Make sure the extension ringer is powered
on with batteries or DC power before
registering it to the telephone base.
2. Place your telephone base into pairing
mode as per the instructions in your
telephone user guide.
3. Press and hold the pair button on the
back of the extension ringer until the
white Flash LED light flashes. The
Extension ringer is now registering to the
telephone base.
Replacing a extension ringer
If you have purchased this new VS014 accessory
extension ringer to replace an old extension
ringer, you must deregister the registered
extension ringer first, and then register this new
extension ringer to your telephone base.
Deregister a extension ringer or all
extension ringers:
• Refer to the User’s manual of your
telephone system to deregister a extension
ringer or all extension ringers.
General product care
Taking care of your extension ringer
Your extension ringer contains sophisticated
electronic and optical parts, so it must be treated
with care.
Avoid rough treatment
Place the extension ringer down gently. Save the
original packing materials to protect your extension
ringer if you ever need to ship it.
Avoid water
Your extension ringer can be damaged if it gets
wet. Do not use the extension ringer outdoors in the
rain, or handle it with wet hands. Do not install the
extension ringer near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power
surges harmful to electronic equipment. For your
own safety, take caution when using electrical
appliances during storms.
Cleaning your extension ringer
Your extension ringer has a durable plastic casing
that should retain its luster for many years. Clean it
only with a dry non-abrasive cloth. Do not use
dampened cloth or cleaning solvents of any kind.
Storage
When you are not going to use the extension
ringer for some time, remove the battery from the
extension ringer. Store the extension ringer in a
cool and dry place.
Frequently asked questions
Below are the questions most frequently asked
about the extension ringer.
The
extension
ringer
doesn’t work
with the
telephone
system
equipment.
• Make sure the unit is connected
to the power supply, or with the
AA alkaline batteries installed.
• The extension ringer may
be deregistered from your
telephone system. Refer to
Add and register a extension
ringer and register the
extension ringer back.
• The extension ringer may be out
of range. Move the extension
ringer closer to your telephone
system.
• If the previous suggestions
do not work, deregister all
devices and register them to the
telephone base again.
Technical specifications
Frequency
control
Crystal controlled PLL
synthesizer
Transmit
frequency
1881.792 MHz - 1897.344 MHz
Channels 10
Nominal
effective range
Actual operating range may
vary according to environment
conditions at the time of use.
Power adaptor Model: S003IV0600045
Input: 100-240V~ 50/60Hz 150mA
Output: 6V 450mA
Battery 3 x AA Alkaline battery
Disclaimer
This product is not designed for security purposes.
When properly installed and maintained, this
product may in some cases reduce the risk of
burglary, fire, robbery or other events occurring
without providing an alarm. VTech is not responsible
for losses, injury, or damage resulting from the use
of this product.
Customer service &
Product warranty
IMPORTANT
Please retain this booklet with your sales receipt as
proof of the date of purchase.
Customer Service
If you require assistance in operating this product
please call the TecHelp Information Line on
1300 369 193 or contact VTech by e-mail at:
tcpsuppor[email protected].
If you are trying to access a Telephone Network
Service and require assistance specifically related
to the network service or would like to subscribe to
the service, contact your service provider.
Voluntary Product Warranty
In addition to your Statutory Rights and subject
to the conditions below, VTech warrants that this
product will be free from any defect in materials or
workmanship under conditions of normal use for a
period of 12 months from date of purchase.
VTech do not warrant that the product will be free
from defects if defects are caused by an accident,
misuse, abuse, improper installation or operation,
vermin infestations, lack of reasonable care,
unauthorised modification, loss of parts, tampering
or attempted repair by a person not authorised by
VTech; or where the product has been damaged by
lightning or a mains power surge.
Where a valid claim is made under this Voluntary
Product Warranty, VTech will, at no cost to you,
repair or replace the product within a reasonable
time. Subject to your Statutory Rights, if your claim
under this Voluntary Product Warranty is not valid,
you may be charged a fee under this Voluntary
Product Warranty for the service and for any direct
costs associated with having the product delivered
for service.
To make a claim under this Voluntary Product
Warranty you must call the TecHelp Information
Line on 1300 369 193 or contact VTech by e-mail
at: tcpsuppor[email protected] where a Customer
Service Representative will inform you of the product
return process. You will need to ensure that:
You provide proof of purchase;
Your product is suitably packaged (original
packaging is not required); and
You have included all components from the original
purchase.
For your records
Date of purchase:
_______________________________
Place of purchase:
_______________________________
Serial number:
_______________________________
For Voluntary Product Warranty purposes proof of
purchase is required so please keep your receipt.
The benefits conferred by this Voluntary Product
Warranty are in addition to other rights and remedies
that are available to you under law, which cannot be
excluded. The processes for this Voluntary Product
Warranty in no way limit your rights which arise as a
result of your Statutory Rights.
This Voluntary Product Warranty is given by:
VTech Telecommunications (Australia) Pty Ltd ABN
70 136 672 627
Address: 24 Gilby Road, Mount Waverley 3149
IMPORTANT NOTE: THIS IS NOT A PRODUCT
RETURN OR SERVICE ADDRESS – PLEASE
CONTACT TECHELP BY PHONE OR EMAIL
FOR PRODUCT AND WARRANTY SUPPORT.
NO LIABILITY WILL BE ACCEPTED BY
VTECH FOR PRODUCTS RETURNED TO THIS
ADDRESS UNDER THIS VOLUNTARY PRODUCT
WARRANTY.
Phone number: 1300 369 193
Email address: [e-mail]
Statutory Rights
Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You
are entitled to a replacement or refund for a major
failure and compensation for any other reasonably
foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not
amount to a major failure.
Vtech Telecommunications (Australia) Pty Ltd.
A member of THE VTECH GROUP OF COMPANIES.
VTech is a registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
© 2018 VTech Telecommunications (Australia).
All rights reserved. Version 2 08/18.
1
1
2
3

Before use
Power on the extension ringer
Option 1 - Connect to the power supply
• Plug the small end of power adapter to the
power jack on the extension ringer, and the
large end to wall jack.
Option 2 - Insert AA batteries
(purchased separately)
• Match the polarity markings (+ and -) inside
the battery compartment.
Add and register a extension ringer
Add your new VS014 extension ringer to your
telephone base. Each new extension ringer
must be registered with the telephone base
before use.
Register a extension ringer:
1. Make sure the extension ringer is powered
on with batteries or DC power before
registering it to the telephone base.
2. Place your telephone base into pairing
mode as per the instructions in your
telephone user guide.
3. Press and hold the pair button on the
back of the extension ringer until the
white Flash LED light flashes. The
Extension ringer is now registering to the
telephone base.
Replacing a extension ringer
If you have purchased this new VS014 accessory
extension ringer to replace an old extension
ringer, you must deregister the registered
extension ringer first, and then register this new
extension ringer to your telephone base.
Deregister a extension ringer or all
extension ringers:
• Refer to the User’s manual of your
telephone system to deregister a extension
ringer or all extension ringers.
General product care
Taking care of your extension ringer
Your extension ringer contains sophisticated
electronic and optical parts, so it must be treated
with care.
Avoid rough treatment
Place the extension ringer down gently. Save the
original packing materials to protect your extension
ringer if you ever need to ship it.
Avoid water
Your extension ringer can be damaged if it gets
wet. Do not use the extension ringer outdoors in the
rain, or handle it with wet hands. Do not install the
extension ringer near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power
surges harmful to electronic equipment. For your
own safety, take caution when using electrical
appliances during storms.
Cleaning your extension ringer
Your extension ringer has a durable plastic casing
that should retain its luster for many years. Clean it
only with a dry non-abrasive cloth. Do not use
dampened cloth or cleaning solvents of any kind.
Storage
When you are not going to use the extension
ringer for some time, remove the battery from the
extension ringer. Store the extension ringer in a
cool and dry place.
Frequently asked questions
Below are the questions most frequently asked
about the extension ringer.
The
extension
ringer
doesn’t work
with the
telephone
system
equipment.
• Make sure the unit is connected
to the power supply, or with the
AA alkaline batteries installed.
• The extension ringer may
be deregistered from your
telephone system. Refer to
Add and register a extension
ringer and register the
extension ringer back.
• The extension ringer may be out
of range. Move the extension
ringer closer to your telephone
system.
• If the previous suggestions
do not work, deregister all
devices and register them to the
telephone base again.
Technical specifications
Frequency
control
Crystal controlled PLL
synthesizer
Transmit
frequency
1881.792 MHz - 1897.344 MHz
Channels 10
Nominal
effective range
Actual operating range may
vary according to environment
conditions at the time of use.
Power adaptor Model: S003IV0600045
Input: 100-240V~ 50/60Hz 150mA
Output: 6V 450mA
Battery 3 x AA Alkaline battery
Disclaimer
This product is not designed for security purposes.
When properly installed and maintained, this
product may in some cases reduce the risk of
burglary, fire, robbery or other events occurring
without providing an alarm. VTech is not responsible
for losses, injury, or damage resulting from the use
of this product.
Customer service &
Product warranty
IMPORTANT
Please retain this booklet with your sales receipt as
proof of the date of purchase.
Customer Service
If you require assistance in operating this product
please call the TecHelp Information Line on
1300 369 193 or contact VTech by e-mail at:
tcpsuppor[email protected].
If you are trying to access a Telephone Network
Service and require assistance specifically related
to the network service or would like to subscribe to
the service, contact your service provider.
Voluntary Product Warranty
In addition to your Statutory Rights and subject
to the conditions below, VTech warrants that this
product will be free from any defect in materials or
workmanship under conditions of normal use for a
period of 12 months from date of purchase.
VTech do not warrant that the product will be free
from defects if defects are caused by an accident,
misuse, abuse, improper installation or operation,
vermin infestations, lack of reasonable care,
unauthorised modification, loss of parts, tampering
or attempted repair by a person not authorised by
VTech; or where the product has been damaged by
lightning or a mains power surge.
Where a valid claim is made under this Voluntary
Product Warranty, VTech will, at no cost to you,
repair or replace the product within a reasonable
time. Subject to your Statutory Rights, if your claim
under this Voluntary Product Warranty is not valid,
you may be charged a fee under this Voluntary
Product Warranty for the service and for any direct
costs associated with having the product delivered
for service.
To make a claim under this Voluntary Product
Warranty you must call the TecHelp Information
Line on 1300 369 193 or contact VTech by e-mail
at: tcpsuppor[email protected] where a Customer
Service Representative will inform you of the product
return process. You will need to ensure that:
You provide proof of purchase;
Your product is suitably packaged (original
packaging is not required); and
You have included all components from the original
purchase.
For your records
Date of purchase:
_______________________________
Place of purchase:
_______________________________
Serial number:
_______________________________
For Voluntary Product Warranty purposes proof of
purchase is required so please keep your receipt.
The benefits conferred by this Voluntary Product
Warranty are in addition to other rights and remedies
that are available to you under law, which cannot be
excluded. The processes for this Voluntary Product
Warranty in no way limit your rights which arise as a
result of your Statutory Rights.
This Voluntary Product Warranty is given by:
VTech Telecommunications (Australia) Pty Ltd ABN
70 136 672 627
Address: 24 Gilby Road, Mount Waverley 3149
IMPORTANT NOTE: THIS IS NOT A PRODUCT
RETURN OR SERVICE ADDRESS – PLEASE
CONTACT TECHELP BY PHONE OR EMAIL
FOR PRODUCT AND WARRANTY SUPPORT.
NO LIABILITY WILL BE ACCEPTED BY
VTECH FOR PRODUCTS RETURNED TO THIS
ADDRESS UNDER THIS VOLUNTARY PRODUCT
WARRANTY.
Phone number: 1300 369 193
Email address: tcpsuppor[email protected]
Statutory Rights
Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You
are entitled to a replacement or refund for a major
failure and compensation for any other reasonably
foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not
amount to a major failure.
Vtech Telecommunications (Australia) Pty Ltd.
A member of THE VTECH GROUP OF COMPANIES.
VTech is a registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
© 2018 VTech Telecommunications (Australia).
All rights reserved. Version 2 08/18.
1
1
2
3