V-tech i6720 User manual

Parts checklist:
Check to make sure the phone’s package includes the following:
1. AC power adapter
2. Charger
3. Handset
4. Battery compartment cover
5. Belt clip
6. Battery
7. Quick installation guide
Install handset battery
NOTE:
• Use only the VTech battery and AC power adapter supplied with this unit or the
recommended equivalent.
• If you are not going to use the telephone for a long period of time, remove the
battery to prevent possible leakage.
• Do not open or mutilate the battery. Released electrolyte is corrosive and mayDo not open or mutilate the battery. Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be toxic if swallowed.
• Exercise care in handling batteries in order not to create a short circuit withExercise care in handling batteries in order not to create a short circuit with
conducting materials such as rings, bracelets, and keys. The battery or
conductor may overheat and cause burns.
             
1. Align the two holes in the plug with the socketpins, matching the red and the
black connectors, then snap plug into place.
2. Place the battery in the compartment with the wires in the upper right
corner.
3. Neatly tuck the wires next to the battery inside the battery compartment.Neatly tuck the wires next to the battery inside the battery compartment.
4. Replace cover by sliding it upwards until it clicks into place.Replace cover by sliding it upwards until it clicks into place.
Connect power to handset charger
Choose the location for your handset charger, and plug charger adapter into an
electrical outlet not controlled by a wall switch.
Charge the handset battery
Place the handset in the base unit.base unit.. CHARGING... will display on handset. Be
sure to charge the battery for at least 16 hours before using your telephone.
Registration
De-register all handsets
• Press and hold FIND HANDSET on the base unit for four seconds, the IN
USE light will light up.
• Keep pressing FIND HANDSET for another six seconds until the IN USE
, then release the FIND HANDSET button.
• Press and release FIND HANDSET again. The IN USE light will turn off and
in a few seconds, all handsets will be de-registered.
-
ister all your handsets, then register the new handset and re-register all the old
handsets one at a time.
Register a handset
• When the handset shows NOT REGISTERED, place
the handset on a base unit or charger that is connected
to a power outlet. The handset screen will display
PRESS FIND HNDST 4 SEC ON BASE.
• Press and hold FIND HANDSET on the base unit
until the IN USE light comes on. (It takes at least four
seconds).
• Release FIND HANDSET once the IN USE light comes
on.
Note:
• If the de-register process does not work, you may need to reset the system
and try again. To reset: pick up the handset and press TALK/ /FLASH.
Then, press the OFF button and place the handset back into the base unit.
 
before registering to base unit.
NOTE:
• Return the handset to the base unit when not in use to ensure optimum
performance.
To attach To remove
NOT RIGISTERD
PRESS FIND HNDST
4 SEC ON BASE
3. Handset
1. AC power adapter 2. Charger
5. Belt clip 6. Battery
4. B at tery c o m p a r tment
cover
After a while the handset will emit series of tones, the newly registered handset
will be assigned the lowest extension number not previously assigned to another
system handset when successfully registered. Repeat the steps in Register
a handset if the new handset does not successfully register to the base unit
within two minutes.
NOTE:
• To purchase replacement batteries, visit us on the web at www.vtechphones.
com or call VTech Communications, Inc. at 1 [phone]. In Canada, go
to www.vtechcanada.com or call VTech Telecommunications Canada Ltd. at
1 [phone].
7. Q u i c k i n s t a l l a ti o n
guide
Belt clip
Align the pins on the inside edge of the clip with the notches on the sides of the
handset.
On the i6725 base:
On the i6765/75/85/86 base:
On the i6725 base:
On the i6765/75/85/86 base:
Quick installation guide
i6720
Important:
If this product is not working properly:
1. Visit our website at www.vtechphones.com or in Canada,
www.vtechcanada.com.
2. Call our customer service at 1-800-595-9511 or 1-800-267-7377 in Canada.
NOTE:
• If PRESS FIND HNDST 4 SEC ON BASE does not appear on the screen after
a few seconds, lift up handset and place in base unit or charger again.