V-tech Drill & Learn Toolbox Pro User manual

Drill & Learn
ToolboxTM Pro
Instruction Manual

2
1
2
3
4
5
6
7
8
9
10 11
12
14
13
INTRODUCTION
Thank you for purchasing the Drill & Learn ToolboxTM Pro!
Get ready for fix-it fun with the drill, hammer and wrench while learning
cool tool facts, numbers, colors, objects and more. Use the project
cards, follow the instructions and enjoy the imaginative repair play. Put
on your tool belt to take the fun on the go!
1Holes 8Hammer
2Tool Buttons 9Wrench
3Mode Selector 10 Nails
4Card Slot
5On/Off/Volume Selector
6Belt Piece A
7Belt Piece B
Screws
11
Project Cards
12
Direction Switch
13
Drill
14

3
Tool Belt Assembly
1. Slide the end of Belt Piece A through the slots on the end of Belt
Piece B.
2. Snap together.
3. Buckle the belt on the child’s waist to play.
INCLUDED IN THE PACKAGE
• Drill & Learn Toolbox™ Pro
• 2 project cards
• 1 tool belt
• 1 drill
• 1 hammer
• 1 wrench
• 2 screws
• 2 nails
• Quick Start Guide
123

4
WARNING
Do not insert anything other than the included screws
or nails into the holes of the toolbox. Doing so may
damage the toolbox.
Rotate the packaging locks 90 degrees
counterclockwise.
Pull out the packaging locks and discard.
Turn the packaging locks counterclockwise
several times.
Pull out and discard the packaging locks.
WARNING
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties, cords and packaging screws are not part
of this toy, and should be discarded for your child’s safety.
NOTE
Please save this Instruction Manual as it contains important information.
ATTENTION
Pour la sécurité de votre enfant, débarrassez-vous de tous les
produits d’emballage tels que rubans adhésifs, feuilles de plastique,
attaches, étiquettes, cordons et vis d’emballage. Ils ne font pas
partie du jouet.
NOTE
Il est conseillé de sauvegarder ce manuel d’utilisation car il comporte
des informations importantes.
Unlock the Packaging Locks

5
GETTING STARTED
Battery Removal and Installation
1. Make sure the unit is turned Off.
2. Find the battery cover located on the bottom of the unit, use a
screwdriver to loosen the screw and then open the battery cover.
3. Remove old batteries by pulling up on one
end of each battery.
4. Install 2 new AA size (AM-3/LR6) batteries
following the diagram inside the battery box.
(For best performance, alkaline batteries or
fully charged Ni-MH rechargeable batteries
are recommended.)
5. Replace the battery cover and tighten the
screw to secure.
WARNING:
Adult assembly required for battery installation.
Keep batteries out of reach of children.
ATTENTION :
Les piles ou accumulateurs doivent être installés par un adulte.
Tenir les piles ou accumulateurs hors de portée des enfants.

6
IMPORTANT: BATTERY INFORMATION
• Insert batteries with the correct polarity (+ and -).
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable
batteries.
• Only batteries of the same or equivalent type as recommended
are to be used.
• Do not short-circuit the supply terminals.
• Remove batteries during long periods of non-use.
• Remove exhausted batteries from the toy.
• Dispose of batteries safely. Do not dispose of batteries in fire.
RECHARGEABLE BATTERIES:
• Remove rechargeable batteries from the toy before charging.
•
Rechargeable batteries are only to be charged under adult supervision.
• Do not charge non-rechargeable batteries.

7
IMPORTANT : INFORMATIONS CONCERNANT LES PILES
Les piles fournies avec le produit permettent de tester le jouet en
magasin mais ne sont pas des piles longue durée.
• Mettre en place les piles ou les accumulateurs en respectant les
polarités + et –.
• Ne pas mélanger des piles ou des accumulateurs neufs avec
des usagés.
• Ne pas mélanger différents types de piles : alcalines, zinc-
carbone et rechargeables.
• Seules des piles du type recommandé doivent être utilisées.
• Ne pas mettre les bornes d’une pile ou d’un accumulateur en
court-circuit (en reliant directement le + et le –).
• Retirer les piles ou les accumulateurs en cas de non-utilisation
prolongée.
• Enlever les piles ou les accumulateurs usagés du jouet.
• Ne les jeter ni au feu ni dans la nature.
PILES RECHARGEABLES
• Enlever, lorsque c’est possible, les accumulateurs du jouet pour
les recharger.
• Les accumulateurs ne doivent être chargés que sous la
surveillance d’un adulte.
• Ne pas tenter de recharger des piles non rechargeables.

8
ACTIVATING NORMAL PLAY MODE
When the product is taken out of the packaging, turn it on and insert
a Project Card. You will hear a beep and a voice confirming you are
in Normal Play mode.
PRODUCT FEATURES
1. On/Off/Volume Selector
To turn the unit On or adjust the volume,
slide the selector to Low or High. To turn the
unit Off, slide the selector to Off.
2. Mode Selector
Slide the Mode Selector to choose an
activity. Choose from three activities.
3. Tool Buttons
Press the Tool Buttons to learn
about tools, answer questions or
listen to cheerful songs.
4. Holes
Drill the Screws or hammer the Nails into
the Holes to play or answer questions.
5. Project Cards
Insert one of the two double-sided Project
Cards into the Card Slot to explore
tools and to hear fix-it songs about tools,
numbers, vehicles and housewares.

9
6. Tool Belt
Insert the tools into the loops on the Tool
Belt for fix-it fun.
7. Drill
Use the Drill to drill Screws into the
Holes. The Drill can turn clockwise or
counterclockwise by sliding the Direction
Switch on the side.
8. Hammer
Use the Hammer to insert the Nails into
the Holes.
9. Wrench
Use the Wrench to insert the Screws into
the Holes.
10. Automatic Shut-Off
To prolong battery life, the Drill & Learn ToolboxTM Pro will shut
off automatically after several minutes without input. The unit can
be turned on again by sliding the On/Off/Volume Selector or
sliding the Mode Selector.
The unit will also automatically turn off when the batteries are
very low.

10
ACTIVITIES
1. Free Play Mode
Press the three Tool Buttons to learn about tools, sounds and colors.
Use the Drill,Hammer or Wrench to drill Screws or hammer Nails
into the Holes. If no Project Card is inserted, you will hear sounds and
phrases. If a Project Card is inserted, you can learn about numbers,
more than or less than, tools, colors, vehicles, objects and more.
After every five actions (drill a Screw, hammer a Nail, etc.), a song
plays in celebration.
2. Challenge Mode
Tool time! Listen to the questions and answer them by using the
tools or pressing the Tool Buttons. When all the Screws and Nails
are inserted into the Holes, pull them out and continue to answer
other questions.
3. Music Fun Mode
Press the Tool Buttons or insert a Project Card to hear songs
about tools, numbers and objects. Listen to the fun melodies by
drilling a Screw or hammering a Nail into the Hole.