V-tech Fire Station 235262 Assembly Instructions

Parent’s Guide
Fire Station
91-003367-000
TM & © 2017 VTech Holdings Limited.
All rights reserved.
Printed in China.

C
M
Y
CM
MY
CY
CMY
K
Grow with VTech(101x127)bw1P-V2.pdf 1 08/18/2014 9:29:01

2
PARKING SPACE
FIRE ENGINE
SPINNING PLATFORM
FIRE HYDRANT
OPEN & CLOSE DOOR
TURNING DOOR HANDLE
FIRE PLATE
LIFT
INTRODUCTION
Thank you for purchasing the VTech®Toot-Toot Drivers®Fire Station!
Place the SmartPoint®fire engine on top of the fire station and watch
him slide down, raise him up in the lift or spin him down the fire pole
to promote motor skill development. The four SmartPoint® locations
trigger songs, melodies, sounds and phrases that will engage your
little one on their playtime mission.

3
One SmartPoint®
fire engine
One SmartPoint®
fire station
One pole
One parking
bracket
One SmartPoint®
base, blue
One house wall
One spinning
platform
One SmartPoint®
lift platform
One base, grey
One flag
One SmartPoint®
parking platform
One top ramp
track support
INCLUDED IN THIS PACKAGE

4
One top ramp
track
One bottom ramp
track support
One 90-degree
track, male
one parent’s guide
One bottom ramp
track
One cross track
Two end tracks,
male
One big fire piece
One label sheet
Two fire plates
Two 1/4 straight
tracks
User’s Manual
UK
Fire Station
TM © 2017 VTech
Printed in China
91-003367-000

5
WARNING:
All packing materials, such as tape, plastic sheets, packaging locks
and tags are not part of this toy, and should be discarded for your
child’s safety.
NOTE:
Please keep this user’s manual as it contains important information.
The toy is surface washable only.
Adult assembly required.
GETTING STARTED
BATTERY INSTALLATION Fire Engine
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the bottom of
the fire engine. Use a coin or a screwdriver
to loosen the screw.
3. Install 2 new AAA (AM-4/LR03) batteries
following the diagram inside the battery
box. (The use of new alkaline batteries is
recommended for maximum performance.)
4. Replace the battery cover and tighten the
screw to secure the battery cover.
Turn the packaging lock anticlockwise
several times.
Pull out and discard the packaging lock.

6
BATTERY NOTICE
• UsenewalkalinebatteriesorfullychargedNI-MH(NickelMetal-
hydride) rechargeable batteries for best performance.
• Useonlybatteriesofthesameorequivalenttypeasrecommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard(carbon-
zinc) or rechargeable (Ni-Cd, Ni-MH), or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
• Remove rechargeable batteries from the toy before charging (if
removable).
• Rechargeable batteries are only to be charged under adult
supervision.
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates they
must not be disposed of in domestic waste as they contain
substances that can be damaging to the environment and
human health.
The chemical symbols Hg, Cd or Pb, where marked, indicate
that the battery contains more than the specified value of
mercury (Hg), cadmium (Cd) or lead (Pb) set out in Battery
Directive (2006/66/EC).
The solid bar indicates that the product was placed on the
market after 13th August, 2005.
Help protect the environment by disposing of your product
or batteries responsibly.
Formoreinformation,pleasevisit:
www.recycle-more.co.uk
www.recyclenow.com

7
Please stick the labels to the play set securely
as indicated on the following page:

8
6 5
9
2
4
3
10
7
1
17
20
23
14
13
18
16
8
19
21
22
25 24 11
12
15

9
ASSEMBLY INSTRUCTIONS
Fire Station
With the VTech
®
Toot-Toot Drivers
®
Fire Station, safety comes first. To
ensureyourchild’ssafety,adultassemblyisrequired.
1. Connect the blue SmartPoint
base and grey base together,
as shown on the right. You
will hear a “click” sound to
indicate they are secure. Once
the bases are attached, they
cannot be removed.
2. Attach the fire station to the
blue and grey bases. You will
hear a “click” sound when
the pieces are secure. Once
the fire station is attached, it
cannot be removed.
3. Insert the top ramp track
support into the grey base.
You will hear a “click” sound
to indicate the piece is secure.
Once the top ramp track
support is attached, it cannot
be removed.
4. Attach the house wall to the
grey base and to the fire
station, as shown below. You
will hear a “click” sound to
indicate it is secure. Once
the house wall is attached, it
cannot be removed.