V-tech Go! Go! SmartWheels Revved Up Stunt Spiral Assembly Instructions

Parent’s Guide
Revved Up Stunt SpiralTM
US
91-003783-008
CA

2
2
2
INTRODUCTION
Thank you for purchasing the Go! Go! Smart Wheels®Revved Up
Stunt SpiralTM toy. Race around the 360° loop and into the race! Press
down on the launcher to send Reggie the Race Car down the track
toward the super launcher. Give it a turn and watch him zip around the
360° loop and out the gate for a roaring finish.This track features two-in-
one fun! Change your track configuration fto create a roller-coaster hill.
SmartPoint®
Race Car
Super Launcher
360° Loop
Launcher
Action Button
Light-Up Face Button
On/Off Switch

3
3
3
INCLUDED IN THIS PACKAGE
NOTE: This toy is not intended for teething.
One base
One handle
One downhill
ramp track
One launcher part B
One uphill ramp
track
One rotator
One ¼ track B
One SmartPoint®
Race Car
One launcher part A
One arc track
One handle
pedestal
One ¼ track A

4
4
4
WARNING
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties and packaging screws are not part of this
toy, and should be discarded for your child’s safety.
NOTE
Please keep this parent’s guide as it contains important information.
ATTENTION
Pour la sécurité de votre enfant, débarrassez-vous de tous les produits
d’emballage tels que rubans adhésifs, feuilles de plastique, attaches,
étiquettes et vis d’emballage. Ils ne font pas partie du jouet.
NOTE
Il est conseillé de conserver ce guide des parents car il comporte des
informations importantes.
Unlock the Packaging Locks
Rotate the packaging lock 360°
counterclockwise.
Pull out the packaging lock and discard.
One label sheet
- Parent’s guide
One sign bracket
One sign

5
5
5
GETTING STARTED
Battery Removal and Installation
1. Make sure the Race Car is turned Off.
2. Find the battery cover located on
the bottom of the unit and use a
screwdriver to loosen the screw and
open the battery cover.
3. Remove old batteries by pulling up
on one end of each battery.
4. Install 2 new AAA (AM-4/LR03)
batteries following the diagram inside
the battery box.
5. Replace the battery cover and tighten
the screw to secure.
BATTERY NOTICE
• Usenewalkalinebatteriesformaximumperformance.
• Useonlybatteriesofthesameorequivalenttypeasrecommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard(carbon-
zinc) or rechargeable, or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity(+and-).
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
• Remove rechargeable batteries from the toy before charging (if
removable).
• Rechargeable batteries are only to be charged under adult
supervision.

6
6
6
MISE EN GARDE
• Utiliser des piles alcalines neuves pour des performances
maximales.
• Seulesdespilesdutyperecommandédoiventêtreutilisées.
• Ne pas mélanger différents types de piles ou d’accumulateurs,
ne pas mélanger des piles ou des accumulateurs neufs avec des
usagés.
• Nepasutiliserdespilesoudesaccumulateursendommagés.
• Mettreenplacelespilesoulesaccumulateursenrespectantles
polarités+et–.
• Nepasmettrelesbornesd’unepileoud’unaccumulateurencourt-
circuit(enreliantdirectementle+etle–).
• Enleverlespilesoulesaccumulateursusagésdujouet.
• Retirer les piles ou les accumulateurs en cas de nonutilisation
prolongée.
• Nelesjeterniaufeunidanslanature.
• Nepastenterderechargerdespilesnonrechargeables.
• Enleverlesaccumulateursdujouetpourlesrecharger.
• Lesaccumulateursnedoiventêtrechargésquesouslasurveillance
d’un adulte.

7
7
7
LABEL APPLICATION
Please stick the labels to the playset securely as
indicated below:
9
3
9
4
8
9 9 10
11 12
13
13
14
15
16
17
18
19
19
8
12
7
16
17
18
2
13 10
13
11
14
5
6
15
1a
1b
1a 1b

8
8
8
ASSEMBLY INSTRUCTIONS
360° Loop Track
With the Go! Go! Smart Wheels®Revved Up Stunt Spiral™,safety
comes first. Adult assembly required. For your child’s safety, do not
let them play with this toy until it is fully assembled.
1. Insert the Launcher Part A into the Launcher Part B.
2. Insert the assembled Launcher onto the Launcher Base.
3. Insert the Handle Pedestal onto the track.

9
9
9
4. Insert the Rotator into the Handle Pedestal.
5. Insert the Handle into the Handle Pedestal.
6. Connect the Uphill Ramp Track with the Downhill RampTrack
as shown below.
7. Insert the Arc Track into the slot on both the Uphill Ramp Track
and the Downhill Ramp Track.

10
10
10
8. Snap the assembled pieces to the front of the track.
9. Connect 1/4 Tracks A and B.
10. Snap the assembled pieces to the end of the ramp track.
11. Add Sign Bracket and Sign to end of track.