V-tech My Busy Workbench User manual

Instruction Manual
My Busy Workbench

2
2
2
INTRODUCTION
Thank you for purchasing the My Busy Workbench.
Let’s build! Get ready for role-play fun with the included workbench,
working toy drill, hammer, spanner, sander, saw and screws. Let’s
get to work!
Circular Saw
Drill Press
Sander
5 Tool
Buttons Gears
Power Tool Zone
3 Power Tools
Ruler Mode Switch
Off/Low/High
Volume Switch

3
3
3
INCLUDED IN THE PACKAGE
• 1 Workbench top • 1 Electronic panel • 1 Back panel
• 1 Back panel top • 2 Panel supports • 4 Legs
• 2 Trays • 1 Left leg support • 1 Right leg support
• 1 Centre tray • 1 Circular saw top • 1 Circular saw base

4
4
4
• 1 Sander base • 1 Sander top • 1 Drill press top
• 1 Drill press base • 1 Project Guide holder • 1 Clock
• 1 Drill • 1 Spanner • 1 Hammer
• 1 Walkie-Talkie • 1 Saw • 1 L-Shaped Spanner

5
5
5
• 1 Vice • 1 Screwdriver • 1 Large gear
• 17 Building pieces • 4 Toy pegs & 4 Toy Wheels
• 10 Blue toy screws & nuts • 5 Toy bolts
For Workbench Assembly
• 19 Grey toy screws & nuts • 10 Real screws
Note:
The grey toy screws and toy nuts are for assembly.
The blue toy screws and toy nuts are play pieces.

6
6
6
• Project Guide
• Quick Start Guide
• 1 Label sheet

7
7
7
WARNING
All packing materials such as tape, plastic sheets, packaging
locks, removable tags, cable ties, cords and packaging screws
are not part of this toy and should be discarded for your child’s
safety.
NOTE
Please save this Instruction Manual as it contains important
information.
Unlock the Packaging Locks
Rotate the packaging locks anticlockwise 90
degrees.
Pull out the packaging locks and discard.
CAUTION:
Adult assembly required. This package contains small parts.
For your child’s safety, do not let your child play with the toy
until it is fully assembled.
CAUTION:
For your child’s safety, do not let your child stand or sit on
the table of the Workbench.

8
8
8
BATTERY INSTRUCTIONS
Battery Removal and Installation
1. Make sure the unit is turned Off.
2. Find the battery cover located on the
back of the electronic panel, use a
screwdriver to loosen the screws, and
then open the battery cover.
3. Remove old batteries by pulling up on
one end of each battery.
4. Install 2 new AA (AM-3/LR6) batteries
following the diagram inside the
battery box. (For best performance,
alkaline batteries or fully charged
Ni-MH rechargeable batteries are
recommended).
5. Replace the battery cover and tighten
the screws to secure.
IMPORTANT: BATTERY INFORMATION
• Insert batteries with the correct polarity (+ and -).
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable
batteries.
• Only batteries of the same or equivalent type as recommended
are to be used.
• Do not short-circuit the supply terminals.
• Remove batteries during long periods of non-use.
• Remove exhausted batteries from the toy.
• Disposeofbatteriessafely.Donotdisposeofbatteriesinre.

9
9
9
RECHARGEABLE BATTERIES:
• Remove rechargeable batteries (if removable) from toy before
charging.
• Rechargeable batteries are only to be charged under adult
supervision.
• Do not charge non-rechargeable batteries.
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates they
must not be disposed of in domestic waste as they contain
substances that can be damaging to the environment and
human health.
The chemical symbols Hg, Cd or Pb, where marked,
indicatethatthebatterycontainsmorethanthespecied
value of mercury (Hg), cadmium (Cd) or lead (Pb) set out
in the Batteries and Accumulators Regulation.
The solid bar indicates that the product was placed on the
market after 13th August, 2005.
Please dispose of your product and batteries responsibly.
In the UK, give this toy a second life by disposing of it at a
small electricals collection point* so all of its materials can
be recycled.
Learn more at:
www.vtech.co.uk/recycle
www.vtech.com.au/sustainability
* Visit www.recyclenow.com to see a list of collection points near you.