V-tech Toot-Toot Drivers Amusement Park Assembly Instructions

Parent’s Guide
Amusement Park
91-003375-001 UK

2
2
2
INTRODUCTION
Thank you for purchasing the VTech®Toot-Toot Drivers®
Amusement Park! Race the Go-Kart down the track through the
360-degree loop and out onto the jump ramp. Then, place the Go-
Kart in the catapult launcher and pull back the lever to get to the top!
Ferris WheelCatapult
Launcher
Roller
Coaster
Hill
6 SmartPointTM
Locations
SmartPointTM
Go-Kart

3
3
3
INCLUDED IN THIS PACKAGE
One roller coaster
structure
One SmartPointTM
Go-Kart
One SmartPointTM
roller coaster platform
One hill supportOne SmartPointTM
hill track
One catapult
lever
One catapult
track support
One SmartPointTM
catapult platform
One catapult arm One catapult track
One base connector
NOTE: This toy is not intended for teething.

4
4
4
One plunger One plunger
top
One SmartPointTM
spinning platform
One spining
ride base
One gate One 60°
male track
One Go! gate One SmartPointTM
gate track
One carnival pieceOne SmartPointTM
ramp base
One flag
Ramp track AOne Ferris wheelThree Ferris
wheel vehicles

5
5
5
Ramp track D
Ramp track C
Ramp track B
Slide track A Slide track B
- One parent’s guide
AB
C
One label sheetTwelve screws
One ramp
track support
Slide track C One slide track support One slide sign
One end track, male

6
6
6
WARNING:
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties and packaging screws are not part of this
toy, and should be discarded for your child’s safety.
NOTE: Please keep this parent’s guide as it contains important
information.
Adult assembly required.
This package contains small screws. For your child’s safety, do
not let your child play with the toy until it is fully assembled.
Unlock the packaging lock:
Turn the packaging lock
anticlockwise several times.
Pull out and discard the packaging lock.
GETTING STARTED
BATTERY INSTALLATION
Go-Kart
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the
bottom of the Go-Kart. Use a
screwdriver to loosen the screw.
3. Install 2 new AAA (AM-4/LR03)
batteries following the diagram
inside the battery box. (The
use of new alkaline batteries
is recommended for maximum
performance).
4. Replace the battery cover and tighten the screw to secure the
battery cover.

7
7
7
BATTERY NOTICE
• UsenewalkalinebatteriesorfullychargedNI-MH(NickelMetal-
hydride) rechargeable batteries for best performance.
• Useonlybatteriesofthesameorequivalenttypeas
recommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard(carbon-
zinc)orrechargeable(Ni-Cd,Ni-MH),ornewandusedbatteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
• Removerechargeablebatteriesfromthetoybeforecharging
(if removable).
• Rechargeablebatteriesareonlytobechargedunderadult
supervision.
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates they
must not be disposed of in domestic waste as they contain
substances that can be damaging to the environment and
human health.
The chemical symbols Hg, Cd or Pb, where marked,
indicate that the battery contains more than the specied
value of mercury (Hg), cadmium (Cd) or lead (Pb) set out
in Battery Directive (2006/66/EC).
The solid bar indicates that the product was placed on the
market after 13th August, 2005.
Help protect the environment by disposing of your product
or batteries responsibly.
For more information, please visit:
www.recycle-more.co.uk
www.recyclenow.com

AB
C
8
8
8
LABEL APPLICATION
Please stick the labels to the play set securely as
indicated on the following pages:
17
6
6
19
16
5
1

9
9
9
30
29
26
24
25
28
28