V-ZUG GS60SZGVI User manual

J163113-R06
Dishwasher EN – Installation instructions
>40 × 80 mm
>80
>40
Appliance components
Front panel/decorative system Base
Recess for pipes
Water tap Power socket
Drain trap connection
Mains connection
Drain pipe
Aqua-Stop/inlet pipe
Before installation, please read the safety precautions on the reverse side!

J163113-R06
EN – Installation instructions
Dishwasher
Extending the water supply and drain pipes and mains cable is not permitted. Consult customer services if you want to make alterations like this.
Do not press on the sides or top of the appliance.
Only move unpacked appliances using gloves. Do not lift appliance when on the plinth.
Always observe the local water supply authority’s regulations.
If the water pressure is <0.1 MPa (1 bar), you need to remove the flow regulator from the appliance connection supports using pointed pliers. To do
this, unscrew Aqua-Stop.
Ventilation outlets in the base must be kept free and not be obstructed (e.g. by carpet).
Electrical connections must be made by trained electricians in accordance with the guidelines and standards for low voltage installations and
the specifications of the local electricity supply companies. A plug-in appliance may only be connected to a socket outlet with earthing contact,
installed according to specifications. An all-pole mains isolating device with 3 mm contact opening should be provided in the house wiring system.
Switches, plug and socket devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching are
permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and fault-free operation. After
installation, live parts and cables with basic insulation must not be accessible. Old installations should always be checked. Refer to the identification
plate for specifications for the required mains voltage, current type and fuses. Application height of the appliance: up to max. 2000 m above sea level.
Do not tip appliance over.
Any old water supply and drain pipes must always be replaced with new ones.
EN Safety precautions
For Service and Spare Part Information please contact:
V-ZUG AUSTRALIA Pty. Ltd.
Tel [phone]

J163113-R06
Dishwasher EN – Installation instructions
1.
Water inlet
Working pressure
Inlet pipe, Aqua-Stop
Water outlet pipe
Disconnect feeder
Water/electrical connection
<60 °C
1–10 bar
1,5 m
G¾"
1,6 m
ø 22 mm
0,1–1 MPa
Minimum ambient temperature +5 °C
2.
Remove all flaps from drain trap
Dummy and non-return valve
3.
Clean drain trap
E.g. with flexible brush
If the water pressure is too high, a pressure reducer valve must be fitted.

J163113-R06
EN – Installation instructions
Dishwasher
4.
Do not bend drain hose
Connect drain hose with drain trap
Fix drain hose with clamp
5.
Fix drain hose at the top with assembly set
7.6.
max. 10 Nm
Check the connection for leaks
Do not bend inlet hose
Connect Aqua-Stop onto the tap
For water pressure at <1 bar:
• Unscrew Aqua-Stop and remove ow regulator
• Replace the lter and seal
• Set to «low water pressure» according to service documents

J163113-R06
Dishwasher EN – Installation instructions
10.
9b
11.
9a8.
230 V~ 50 Hz, 16 A
3 × 1,5 mm²
230 V~ 50 Hz, 10 A
3 × 1 mm²
400 V 2N~ 50 Hz, 10 A
4 × 1 mm²
Installation test
Connect up to building supply
Plug inCheck connection values
The building connection must
match the information on the
identification plate.
Connection values:
Connect feeder again
black brown blue yellow/green

J163113-R06
EN – Installation instructions
Dishwasher
OK!
1.
5.
2.
3.
A2 A9 U1/U2
4.
Installation test is complete, appliance is ready to use
Empty the appliance
Once the end of the programme is displayed (see operating instructions):
Water outlet fault Water inlet fault Voltage fault
Close appliance door The test starts in 15 seconds
within 15 seconds
תוינש 15 ךותב
It takes approx. 2 minutes
If error messages occur:
rectify fault according to the operating instructions
Installation test
Select the test by pressing and holding down the + buttons at the
same time