Vaderstad ISOBUS User manual

Quick Start ISOBUS Task Controller
Fendt VarioTerminal 10.4
Terminal Software: 781
903114,2017-01-251

Denna Quick Start ersätter inte instruktionsboken!
Denne Quick Start erstatter ikke instruktionsbogen!
Denne Quick Start erstatter ikke instruksjonsboken!
Tämä Quick Start-pikaopas ei korvaa käyttöohjekirjaa!
This Quick Start guide does not replace the instruction manual!
Diese Quick Start-Anleitung ist kein Ersatz für das Handbuch!
Ce guide Quick Start ne remplace pas le manuel d’instructions!
Instrukcja szybkiego uruchomienia nie zastępuje instrukcji obsługi,
którą należy przeczytać przed rozpoczęciem użytkowania
maszyny. Šis ātrais mācību materiāls neaizvieto lietošanas
instrukciju!
Šis „Quick Start“ vadovas nepakeičia instrukcijos!
See kiirjuhend Quick Start ei asenda kasutusjuhendit!
Návod Quick Start nenahrazuje návod k použití!
Ez a Quick Start útmutató nem helyettesíti a Használati útmutatót!
La presente guida Quickstart non sostituisce il manuale di
istruzioni!Это руководство «Quick Start» не заменяет основное
руководство по эксплуатации!
Ta vodnik Quick Start ne nadomešča priročnika z navodili!
Този бърз справочник не заменя наръчника!
Ο παρών οδηγός Γρήγορης εκκίνησης δεν αντικαθιστά το εγχειρίδιο οδηγιών!

Väderstad ISOBUS implement with
Fendt VarioTerminal 10.4”
1 (5)
Issued by
Date
Edition
Niklas Rosén
2017-01-25
1.0
Väderstad ISOBUS implement with
Fendt VarioTerminal 10.4”
NOTE! This document is a quick guide only and requires that the Väderstad
implement is connected correctly and that the user possesses some basic knowledge
of how this display and it´s functions is working. For further information regarding
display functions we refer to the user manual provided by the manufacturer.
TIP! Some chapters in this guide refers to the displays user manual. Before you use
this guide in field, please read through this guide completely and make sure you have
access to the required documentation.

Väderstad ISOBUS implement with
Fendt VarioTerminal 10.4”
2 (5)
2
1. Introduction
When installing and running a Väderstad ISOBUS implement with a ISOBUS terminal, it is
important to follow and complete the steps in this guide.
This document is a quick guide only and requires that the Väderstad implement is connected
correctly to the display and that the user possesses some basic knowledge of how this display and
it´s functions is working. For further information regarding display functions we refer to the
operators manual provided by the manufacturer.
Before you proceed to the next chapter, please ensure that both the terminal software and the
Väderstad software matches the one specified on the Väderstad homepage.
http://www.vaderstad.com/products/vaderstad-e-services/isobus
2. Check the terminal software version
It´s important that the display software matches the one tested from Väderstad. If the display
software separates from the one tested, some functionality may not work as expected.
To view the display software version, from the main screen, press:
Tractor Info -> Tractor Main Menu -> Service & Diagnostics ->
Diagnostics
Check the row saying “Software Compound ”.
Screen 1. Display diagnostics screen.
If the software version is incorrect, please contact your local Fendt dealer. If the version matches
please continue to the next step.

Väderstad ISOBUS implement with
Fendt VarioTerminal 10.4”
3 (5)
3
3. Check Activations
In order for “Section Control” and/or “Variable Rate” to work the display must be unlocked with a
specific license. If the display is locked, please advise your local display reseller in order to
purchase this activation.
To view the display activations, from the main screen, press:
Administration Info -> Administration Main Menu -> ISOBUS Information
.
Make sure “Task Controller” is activated.
Screen 2. Display activations
4. Creating a implement on the display
When Task Controller is used the Fendt VarioTerminal automatically creates a implement profile,
please proceed to the next chapter of this guide.
5. Activating Task Controller in Väderstad User Interface (UI)
Open the “Väderstad UI”. In the Väderstad UI, press “Settings”, on the next screen press “General
Settings”. Toggle the Task Control button to “ON” (screen 3).

Väderstad ISOBUS implement with
Fendt VarioTerminal 10.4”
4 (5)
4
Screen 3. Task Controller ON
Once the Task Controller is set to “ON” a new implement will be detected by the display.
From the general settings, press the “TC-submenu” button. In this menu you´re telling the display
what product to be controlled and also what functions to be used by turning “Section Control”
and/or “Variable Rate” to ON or OFF. In this menu you´re also able to set the implement offsets
and ON/OFF timers for each product. For further information regarding these settings please read
the “Task Control”-chapter in the Väderstad E-Control user manual.
Screen 4. TC- Submenu Tempo
Screen 5. TC-Submenu RD/RDA
When all settings is set and the TC-submenu is exited the Task Controller object pool is updated
and sent to the display. After 20 seconds the implement profile is updated with the latest settings.
WARNING: No changes in the TC-submenu is to be done when a job is created. If changes is done
while a task is started, the gateway and the display may end up in bad state causing rate/coverage
feedback to be lost or implement changes not to be updated.

Väderstad ISOBUS implement with
Fendt VarioTerminal 10.4”
5 (5)
5
6. Create job and/or enter necessary documentation settings
If VarioDoc is to be used in order to do documentation of the work being performed, please see
chapter 4, “VarioDoc usage (35)” in the VarioDoc operators manual.
7 Use of “Section Control”
7.1 Create field and field boundaries
If section control is to be used when exiting field and/or headland boundaries these must be defined.
For further information, please see chapter 8.12, “Field settings (133)” in the VarioGuide operators
manual.
7.2 Section Control Settings
If section control is to be used when exiting field and/or headland some settings must be set. For
further information, please see chapter 7, "Section Control (101)" in the VarioDoc operators
manual.
8 Use of “Variable Rate”
9.1 Import/Load shapefile
If “Rate Control” is to be used, a prescription file must be used. For further information, please see
chapter 8, “Variable Rate Technology (115)” in the VarioDoc operators manual.
9 Attachments
NOTE! A full version of the VarioDoc and VarioGuide operators manuals is not available online,
please contact your local reseller.
Operators manual: VarioDoc (Section Control & Variable rate, November 2016).
Operators manual: VarioGuide (VarioGuide NovAtel & VarioGuide Trimble, November 2016).
Väderstad E-Services Rapid
http://pdmlink.vaderstad.com/openext.aspx?id=10065801
Väderstad E-Services Rapid A
http://pdmlink.vaderstad.com/openext.aspx?id=10043228
Väderstad E-Services Tempo L
http://pdmlink.vaderstad.com/openext.aspx?id=10064506
Väderstad E-Services Tempo T, Tempo F, Tempo V, Tempo R, FH
http://pdmlink.vaderstad.com/openext.aspx?id=10038077
Väderstad E-Services Spirit och Spirit R
http://pdmlink.vaderstad.com/openext.aspx?id=10052287

Väderstad AB
SE-590 21 VÄDERSTAD
Phone: [phone]
www.vaderstad.com