VADO LIFE LIF-200-CP User manual

Mono Basin Mixer
LIFE
Keep for future reference
Installation Guide
LIF-200-CP
Vado
Wedmore Road, Cheddar, Somerset, England BS27 3EB
tel [phone]. fax [phone]
[e-mail]
www.vado.com
This instruction booklet covers these models:
LIF-200-CP.
Version 1, 1-8-17
where inspiration flows

2 3
Please read these instructions carefully before starting installation and keep for future
reference.
Remove all packaging and check the product for missing parts or damage before
starting installation.
Any alterations made to this product and fittings may infringe water regulations and
will invalidate the guarantee.
The installation must comply with all Local/National Water Supply Authority
Regulations/Byelaws and Building and Plumbing Regulations.
To be installed in accordance with BS EN806.
We strongly recommend that you use a qualified and registered plumber.
General installation
This fitting is a mixing device and therefore water supplies should be reasonably
balanced.
When installed, the fitting must comply with the requirements of the Water Supply
(Water Fittings) Regulations 1999 and Scottish Byelaws 2004.
For further information, contact the Water Regulations department of your local water
supplier (see the WRAS website www.wras.co.uk for details) or the Water Regulations
Advisory Scheme by email ([e-mail]) or telephone: [phone].
Before making any inlet pipe connections, all supply pipes MUST be thoroughly flushed
to remove debris. Failure to do so could result in damage or low flow from the mixer
unit. Water Supply (Water Fittings) Regulations 1999 Schedule 2 Section 13.
The fitting of isolating valves to the inlet feeds is advised for ease of maintenance.
Please take great care when installing this mixer not to damage its surface.
Please note if installing in an enclosed environment, access should be left for servicing
and maintenance. No costs relating to inadequate access can be accepted.
Operating Specifications
Operating Pressure
Minimum operating pressure 1 bar
Maximum operating pressure 5 bar
Important - please read Contents of Packaging
Valve bodyAerator removal key
Rubber washer
Flexible hoses
(Red for hot,
Blue for cold)
Metal washer
Hex key
Threaded rod
Nut
Mono Basin Mixers
LIFE
Keep for future reference
Installation Guide
LIF-200-CP
WHERE
INSPIRATION
FLOWS
LIFE
Mono Basin Mixer
User Guide
Keep for fut ure reference
Installation guide &
User manual
FIXING KIT BOX

45
Dimensions
36mm
50mm148mm
112mm
98mm
325mm 142mm
½"
1
2
Max - 5 Bar
1
2 3
4
0 5
Min - 1 Bar
1
2 3
4
0 5
Installation - Quick guide
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
1
2 3
4
0 5
60mm

6 7
Installation
Before installing your new mixer, flush
through the pipe work to ensure removal
of debris, turn off the water supply.
Make sure that the seal is in position in
the base of the mixer body.
Position the mixer on the basin. From
the underside of the basin screw the
two flexible pipes to the hot and cold
connections in the mixer body, the hot
should be to the left and the cold to the
right, hand tighten only.
Screw the threaded rod into the back hole
in the base of the mixer body.
Slide the rubber and metal washers over
the rod, the rubber washer should be
on top. Make sure that raised V part of
the rubber washer sits in the groove of
the metal washer. Screw on the nut and
tighten to clamp the mixer to the basin.
CAUTION: Do not over tighten the nut as
this may damage the basin.
Connect the water supply to the inlet
pipes. The hot water should be connected
to the left pipe and cold to the right.
CAUTION: When
installing the
flexible hoses do
not kink, or bend
them more than the
60mm diameter as
shown right.
60mm
Base
Rubber washer
Metal washer
Hot flexible
hose (red)
Cold flexible
hose (blue)
Nut
Threaded
rod
Seal
Notes: