VADO wg-rrk/div-148 Installation and operating instructions

wg-rrk/div-148
Vado
Wedmore Road, Cheddar, Somerset, England BS27 3EB
tel [phone]. fax [phone]
[email protected]
www.vado-uk.com
Guarantee
Customer/technical services
For any technical or installation queries please contact Vado on 01934 745163.
GUARANTEE REGISTRATION
NAME
ADDRESS
RETAILER
ADDRESS
PURCHASE DATE
PRODUCT DESCRIPTION
WHO INSTALLED THE PRODUCT?
FOR VADO USE
POSTCODE
POSTCODE
ARTICLE NUMBER (SEE BOX)
RETAILER PLUMBER BUILDER SELF
This product is guaranteed against manufacturing defects from the date of purchase until the expiry of the relevant
guarantee period shown below.
The guarantee is only valid if:-
1. The product has been installed, used and maintained in accordance with Vado’s instructions and subjected to
normal use only.
2. The defect is not due to use of an unsuitable or inadequate water or power supply.
3. The defect is not due to accident, misuse, neglect or repair other than by Vado or Vado authorised agents or
damage caused by foreign objects or substances.
4. We have received from you the completed Guarantee Registration Form. Vado accepts no responsibility for any
forms lost in the post and returns by registered means is therefore recommended.
Under this guarantee (which is non-transferable) Vado will, at its option, repair or replace free of charge any product
(or replacement part) found to be defective. The guarantee does not extend to any consequential loss or damage.
After repair or replacement the relevant guarantee period will be calculated from the original date of purchase.
The relevant guarantee periods are:-
1. Twelve years on chrome nish products.
2. Six years on Vado Identity products.
3. Three years on all other products with the exception of Stuart Turner Pumps which carry a 2 year Guarantee on
Monsoon Range and 1 Year Guarantee on Showermate Range.
All claims under the guarantee must be submitted in writing to the person who supplied the product to you and
must be received no later than the last day of the relevant guarantee period. All claims must be accompanied by
proof of purchase (sales receipt or delivery note).
Vado operates a policy of continuous product development and therefore reserves the right to change the product,
packaging and documentation specications without notice.
This guarantee is in addition to and does not aect your statutory rights as a consumer.
Rigid riser kit with diverter and
integral outlet for use with concealed valves
Installation & maintenance instructions
Please leave these instructions with the customer

Important - please read
27
Installers/users notes
Please read these instructions carefully before starting installation and keep for future
reference.
Remove all packaging and check the product for missing parts or damage before
starting installation.
Any alterations made to this product and ttings may infringe water regulations and
will invalidate the guarantee.
The installation must comply with all Local/National Water Supply Authority
Regulations/Byelaws and Building and Plumbing (UK:BS6700) Regulations.
We strongly recommend that you use a qualied and registered plumber.
Installer must comply with current regulations.
Please note if installing in an enclosed environment, access should be left for servicing
and maintenance. No costs relating to inadequate access can be accepted.
Care of the mixer
Our products are nished to the highest standard and due care needs to be taken to
ensure their looks are retained.
We recommend cleaning all products with a soft damp cloth ONLY and advise strongly
against the use of ALL cleaning products i.e. powders and liquids.
If the above instructions are not followed this will invalidate your guarantee in the
event of a problem occurring.

6
Dimensions
3
Operating Specications
Operation
Hot Water Supply Temperature:
Maximum: 85° C
Minimum: 10° C higher than the maximum required mixed temperature (advise 65° C)
Operating Pressure:
Minimum operating pressure 1 bar
Maximum operating pressure 5 bar
1152mm
110mm
64mm
577mm
110mm
254mm
254mm
To divert the water from the handset to
the riser, turn anti-clockwise.
To divert the water from the riser to the
handset, turn clockwise.
Maintenance
To remove any build up of limestone on
the handset and shower head, just rub
your ngers lightly over the nozzles.
1090mm

Installation
45
Installation
Warning! Please check for any hidden
cables and pipes before drilling holes in
the wall.
Assemble the top riser to the wall mount.
Push the top riser into the mount locating
the ats of the nut, make sure that the
hoop of the top riser is pointing away
from the wall and the grubscrew is on
the underside of the mount. Tighten
the screw within the mount to secure
together using a cross head screwdriver.
Screw the riser into the bottom of the
mount.
Mark a centre line up the wall, hold the
assembly in position and mark a point
for the riser mount and a point for the
diverter, bearing in mind the dierent
heights of people using the shower.
Using a 6mm drill bit for the wall plug, drill
the wall at the top marked position and
x the mount boss in position using the
supplied wall plug and screw.
Prepare the wall for the diverter using
a ush ½” connector. This should be
connected to the shower valve. Using
PTFE tape screw the adapter into the
connector and tighten.
Take the riser rail assembly and push the
mount onto the boss and the diverter
onto the adapter and secure using both
hexagonal grub screws.
Finally screw the shower head onto the
top riser.
Hose connection
Wall plug
Shower head
Shower head
holder
Mount
boss
Diverter
Riser
Showerhead
Place one of the rubber washers into the
cone end of the hose and screw to the
handset.
Place the second rubber washer into the
other end of the hose and attach it to
the diverter.
Screw
Top riser
Mount
Top riser
Mount
Grub screw
Grub screw
Adapter
½” ush
mounted
connector
Grub screw