Vaillant VRT 50 Specification sheet

0020030718_01 GB 11 2006
Operating and
Installation Manual
VRT 50
Room thermostat
GB
For the installer
1
VRT 50 Room Thermostat Operating and Installation Manual
Notes on the documentation
The following notes are intended to help you throughout
the entire documentation.
Further documents apply in combination with this oper-
ating and installation manual.
We accept no liability for any damage caused by fail-
ure to observe these manuals.
Storage of the documents
Please pass on this operating and installation manual to
the owner of the system so that he or she can make it
available whenever it is required.
Symbols used
Please observe the safety instructions in this manual for
the installation of the device.
hNote!
Useful information and instructions
• Symbol for a necessary task
Safety
The (programmable) room thermostat must be installed
by an approved qualified servicing company, which is re-
sponsible for adhering to the existing standards and
regulations.
Operating instructions
1 Overview
1
Key
1 Display
2 Dial
(turn and click)
2
Fig. 1.1 Overview of the device
4
32
1
Key
1 Hot water symbol
2 Flame display/
Boiler malfunction
3 Temperature display
4 Boiler installer level/
maintenance request
Fig. 1.2 Overview of the display
2 Description of the device
The VRT 50 is a room thermostat for connecting to Vail-
lant ecoTEC combination boilers (with eBus).

VRT 50 Room Thermostat Operating and Installation Manual2
The VRT 50 allows the user to set the room tempera-
ture. It also allows the user to control the boiler warm-
start function.
Furthermore the controller shows you the heating re-
quirements for hot water and operation or any malfunc-
tion/maintenance messages of the boiler.
3 Operation
The operating principle is based on a dial (Vaillant “turn
and click” operating concept).
The current room temperature is displayed on the basic
display. The hot water symbol is displayed whenever
there is a hot water requirement or the warm start func-
tion is activated.
The “flame” symbol is displayed when the boiler is in
operation. The “boiler malfunction” symbol is dis-
played if there is malfunction to the boiler. Maintenance
requests of the boiler are indicated by the “spanner”
symbol flashing.
3.1 Setting the target room temperature
The current room temperature is displayed on the basic
display.
• Turn the dial (basic display).
The ACTUAL temperature disappears from the display
and the set target room temperature appears and starts
to flash.
• You can set the target room temperature directly
(after about 1 second) to the desired value by turning
the dial.
The basic display reappears after about 5 seconds.
3.2 Activating the warm start function
The warm start function of the boiler can be switched on
or off with the VRT 50.
This is convenient for long periods of absence to avoid
unnecessary consumption of energy.
hNote!
To use this function, you need to have activated
the warm start function on your boiler. You can
find appropriate instructions in the operating
manual of your boiler.
• You can switch on the warm start function by pressing
and turning (after one second) the dial.
• You can switch off the warm start function by pressing
and turning (after one second) the dial again.
4 Vaillant warranty
See supplement 0020029010.
5 Recycling and disposal
Neither your (programmable) room thermostat nor any
of its accessories belong in the household waste.
Make sure the old device and any existing accessories
are disposed of properly.
Installation instructions
6 Notes on the installation and
operation
The installation, electrical connection, settings and initial
start-up of the device may be performed only by an ap-
proved qualified servicing company.
6.1 CE label
The CE label documents that the VRT 50 (programma-
ble) room thermostat, when connected to Vaillant boil-
ers, meets the basic requirements of the directive on
electromagnetic compatibility (89/336/EEC) and the low
voltage directive (73/23/EEC).
6.2 Intended use
The VRT 50 room thermostat is a state-of-the-art device
which has been constructed in accordance with recog-
nised safety regulations. Nevertheless, there is still a risk
of death or injury to the user or others or of damage to
the device and other property in the event of improper
use or use for which it is not intended.
The VRT 50 room thermostat is used for the room-de-
pendent control of a heating system with boiler with
eBUS interface from Vaillant.
Any other use or extended use is considered to be im-
proper. The manufacturer/supplier is not liable for any
resulting damage. The owner alone bears the risk.
Intended use includes the observance of the operating
and installation manual.
hNote!
The VRT 50 must not be connected to the boil-
er in conjunction with any other eBus room
thermostat or eBus programmer. It can only be
used in conjunction with the timeSWITCH 130
analogue central heating programmer.

3VRT 50 Room Thermostat Operating and Installation Manual
7 Safety instructions and regulations
The device must be installed by an approved qualified
servicing company, which is responsible for adhering to
the existing standards and regulations.
We accept no liability for any damage caused by failure
to observe these instructions.
All wiring must be in accordance with Building Regula-
tions Part P and BS 7671 (IEE Wiring Regulations), and
must be carried out by a suitably qualified person.
Use standard commercial cables for wiring.
- Minimum cross-section of the wires: 0.75mm2
Do not exceed the following maximum wire lengths:
- Bus lines: 300m
230 V connection lines and bus lines must be laid sepa-
rately if they are longer than 10 m.
The controller may only be installed in dry rooms.
8 Installation
8.1 Place of installation
m5.
1
Fig. 8.1 Selecting the place of installation
8.2 Mounting the room thermostat
23 1
Fig. 8.2 Opening the (programmable) room thermostat
The thermostat is connected to the boiler with a two-
wire bus cable (eBUS).
• Open the (programmable) room thermostat by undo-
ing the snap-fit on the bottom (2), flapping the cover
of the housing (1) upwards and removing it from the
base of the housing (3).
4
3
5
6
Fig. 8.3 Mounting the (programmable) room thermostat
• Drill two holes (5) of 6 mm diameter and insert the
supplied wall plugs.
• Lay the connection cable through the duct (6).
• Attach the housing base (3) to the wall with the two
screws provided.
• Connect the connection cable as described in Sec-
tion 10.
• Close the housing by placing the cover of the housing
with the top edge in the snap-fit (4) of the housing
base, flapping it downwards and pressing it until you
hear it snap into place in the housing base.
9 Electrical installation
The electrical connection may be carried out only by an
approved qualified servicing company.
9.1 Connecting the room thermostat
The thermostat communicates with the boiler via a
two-wire bus cable (eBUS). All eBUS connector plugs are
designed to allow you to wire at least 2 x 0.75 mm2(rec-
ommended) per connection terminal. This means that
the wires can be swapped without impairing communica-
tion (see Fig. 9.1). Also follow the instructions for the
boiler.
hNote!
- A bridge must be inserted at the boiler be-
tween terminals 3 and 4 when the VRT 50 is
installed.
- No other eBUS controllers can be connected
to the boiler in addition to the VRT 50.
- The VRT 50 must be used in conjunction with
the timeSWITCH 130.

VRT 50 Room Thermostat Operating and Installation Manual4
VRT 50
-+789
- BUS + 7 8 9
Boiler
LN 345
LN 345
Fig. 9.1 Electrical connection
10 Start-up
No additional settings are required for the start-up.
The heating engineer can additionally adapt the (pro-
grammable) room thermostat to the environment or the
preferences of the user.
10.1 Installer level
You can go to the installer level by pressing the dial for
about 10 seconds.
The spanner symbol appears on the display.
• You can switch to the next parameter by pressing the
dial.
The following parameters can be set:
Parameter 1: Setting of a minimum temperature as a
lower limit for the control range
You can set a minimum temperature by turning the dial.
Setting range 5 … 30° C (default setting: 15° C)
Parameter 2: Switchover between two-point and contin-
uous control
You can change the parameter by turning the dial.
0 = two-point control (default setting)
1 = continuous control
You can exit the installer level as follows:
• Press the dial for about 5 seconds
or
• After 5 minutes if you do not operate the dial.
The basic display then reappears.
10.2 Handing over the device to the owner
The owner of the (programmable) room thermostat
must be instructed about its functions and how to oper-
ate it.
• Hand over the manuals intended for the owner as well
as the documents of the device.
• Go through the operating manual with the owner and
answer any questions.
• Draw special attention to the safety instructions,
which the owner must follow.
11 Technical data
Description Unit Value
Operating voltageUmax V24
Maximum permissible ambient temperature °C 50
Current consumption mA 17
Minimum cross-section of the connection lines mm20.75
Level of protection IP 20
Protection class for controller III
Dimensions
Height mm 97
Width mm 97
Depth mm 27
Table 11.1 Technical data
12 Vaillant service
To ensure regular servicing, it is strongly recommended
that arrangements are made for a Maintenance Agree-
ment. Please contact Vaillant Service Solutions (0870
6060 777) for further details.