VALCOBABY Maxi Cosi Car Seat Adaptor Installation and operation manual

Thank you for purchasing a quality VALCO product. Please read and follow the instructions outlined in this
guide carefully. Familiarise yourself with the construction and safety features; be sure that you understand all
the warnings and safety guidelines before use.
Retain this guide in a safe place for future reference.
PRODUCT REFERENCE GUIDE
MAXI COSI CAR SEAT ADAPTOR
© Copyright VE 2009
Due to our policy of continuous product
development, this product is constantly
evolving. It is possible that some features
or procedures outlined here have changed
since this document was written. If you are
unsure of any procedure shown here, please
contact us via email at [e-mail]
or Canada customers can email canada@
valcobaby.com to obtain the most up to date
information before use. Include the batch
number, which can be found on a sticker on
the frame.
All pictures and diagrams herein are provided
for illustration purposes only. Actual product,
color or fabric may vary. VALCO reserves the
right to modify or alter any specication or
color without notice or obligation to modify
any product previously purchased
FURTHER INFORMATION
In North America only
www.valcobaby.com
1800 610 7850
In Canada only
416 488 1900

TO USE YOUR MAXI COSI
CAR SEAT ADAPTOR
SINGLE/TWIN:
If you haven’t already done so, remove
the front bar or plugs from the nylon
housings on either side of the stroller
frame by pressing each inner ‘release
button’ and lifting the front bar or plug
from the housing.
Insert the car seat adaptor connecting
pieces into the nylon housings.
Be sure that the bar release button is
securely in the housing.
Position the Car Seat so that infant is
facing the handlebar of the stroller.
Line up the Car Seat to the Adaptor
frame ensuring that the Car Seat rests
comfortably in the Adaptor frame.
C
B
The following instructions are for the Valco Baby
TriMode Models.
A
B
C
Insert Car Seat Adaptor
Place Car Seat in Adaptor
Bumper Bar
Nylon Plug
press
Remove Bumper Bar or Housing
A

Turn the stroller so you are facing the car
seat front.
Locate the strap hanging from the front
metal bar.
Undo the strap.
Pull the female clip over the front hook
of the car seat.
Place the male clip under the front adap-
tor bar.
Insert the Male clip into the Female clip
and fasten.
Ensure that the strap is tight and se-
curely fastened by pulling on the free
end of the strap.
Once the car seat is in position, take the
remaining black straps and place them
through the sides of the car seat, (where
a seat belt would go) and connect via the
buckle.
Ensure that the strap is tight and se-
curely fastened by pulling on the free
end of the strap.
TO REMOVE THE CAR SEAT:
Detach the straps (reversing the process
outlined in E & F) and lift the car seat
out of the frame.
TO REMOVE THE ADAPTOR:
Feel the side of the Nylon Housing that
sits below the frame at each side and
locate the release button.
Press the release button and lift the
adaptor bar out of the nylon housings.
E
D
D
E
F
Side View Front View
Pull to
tighten
Front View
Side View
F

WARNINGS
Your child’s safety is your responsibility ………
Be sure to check that all clamps and buckles are securely xed and in place •
before use.
Check all parts for breakage or fatigue before use. Discontinue immediately•
if any part is found to be damaged or broken.
Do not use this Car Seat Adaptor bar until you have read and understood all•
of the instructions.
This adaptor is compatible for use with Maxi Cosi car seats. DO NOT use •
with any other brand.
Only use this adaptor with the correct model VALCO Trimode Single or Twin•
Stroller accordingly.
Never leave your child unattended.•
Make sure and check that the Car Seat Adaptor bar, as well as the Car Seat•
are securely fastened before each use.
ALWAYS ensure that each child is clear of all moving parts when adjusting•
the stroller.
WARNING: Avoid serious injury from falling or sliding out. Make sure that the•
child is harnessed into the Car Seat using the manufacturer’s instructions,
at all times.
This product is intended for use with infants whose Weight is: 5 - 30 lbs and•
Height: under 30 inches. Excessive weight may cause a hazardous unstable
condition to exist.
WARNING: Please be aware that this instructions manual is strictly for•
the VALCO Car Seat Adaptor. Please know and understand the Car Seat
manufacturers instructions before use.
Parcels, accessory items or both that are placed on the unit may cause the•
unit to become unstable.
Do not use accessories not designed for your stroller as they may be•
unsafe.
This product is intended for domestic use only. It is not intended for•
commercial use.
North America
www.valcobaby.com
In USA only
1 800 610 7850
In Canada only
416-488-1900