VALCOBABY TRAVEL SYSTEM ADAPTOR Installation and operation manual

Thank you for purchasing a quality Valco Baby product. Please read and follow the instructions outlined in this
guide carefully. Familiarise yourself with the construction and safety features; be sure that you understand all
the warnings and safety guidelines before use.
Important: Please read the following instructions carefully before assembling this product. Retain this
guide in a safe place for future reference.
PRODUCT REFERENCE GUIDE
© Copyright VE 2009
Due to our policy of continuous product
development, this product is constantly
evolving. It is possible that some
features or procedures outlined here
have changed since this document
was written. If you are unsure of any
procedure shown here, please contact
us via the web at [e-mail] to
obtain the most up to date information
before use. Include the batch number,
which can be found on a sticker on the
frame.
All pictures and diagrams herein are
provided for illustration purposes only.
Actual product, colour or fabric may
vary. Valco Baby reserves the right to
modify or alter any specication or colour
without notice or obligation to modify any
product previously purchased
FURTHER INFORMATION
In Australia/New
Zealandwww.valco.com.au
In North America only
www.valcobaby.com
1800 610 7850
TRAVEL
SYSTEM
ADAPTOR
FOR ION FOR 2

aDaPTOR aSSEMBLY
FIGURE A
1. Remove the Car Seat Adaptor from packaging. Dispose
of all packaging thoughtfully. Identify all parts on the
Adaptor:
a. Adaptor Fixing brackets
b. Front locking hooks
c. Back locking uprights
FIGURE B
2. The Valco Travel System is made to accommodate the
Britax Unitiy™ Car seat.
FIGURE C - INSTALLING THE ADAPTOR
3. Recline the seat of your stroller as far as it allows and
push the hood back completely. Remove the bumper bar
as per the manufacturer’s instructions and store in a
safe place.
4. Position the Adaptor so the front locking hooks (a) face
forward (4).
5. Position the Adaptor directly over the stroller seat and
align the adaptor xing brackets with the bumper bar
housings.
6. Lower the Adaptor carefully into the bumper bar housings
until both sides engage into place.
IMPORTaNT NOTE: aLWaYS TEST THaT THE CaR SEaT
aDaPTOR HaS BEEN FULLY ENGaGED INTO POSITION
BEFORE aTTaCHING YOUR CaR SEaT.
FIGURE D - USING YOUR TRAVEL SYSTEM
7. Tilting the car seat slightly, align the locking bracket at
the rear of the seat with the front locking hooks (b) on
the adaptor.
A
B
C
D
a
a
c
c
b
b
b
4

FIGURE E
8. Push down on the seat rmly until you feel the rear
locking uprights click into place.
IMPORTaNT NOTE: aLWaYS TEST THaT THE SEaT IS
SECURELY ENGaGED BY PULLING UP ON IT SLIGHTLY
FIGURE F - REMOVING THE SEAT
9. Release the seat catch in the same manner as you
would release the seat from the car, by pulling upward
on the release catch at the front of the car seat and lift
the seat smoothly upward.
E
F
LIFT SMOOTHLY
UPWARDS
RELEASE
CATCH
9

WARNING
• FOLLOW THE MANUFACTURER’S INSTRUCTIONS.
• PUT ON ALL THE BRAKES WHENEVER YOU PARK THE PRAM/STROLLER.
• DO NOT LEAVE CHILDREN UNATTENDED.
• DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS PRAM/STROLLER.
• MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU ADJUST THE PRAM/STROLLER.
OTHERWISE THEY MAY BE INJURED.
Remember, your child’s safety is your responsibility...
• NEVERUSEONStaiRSORESCaLatORS.
• aLwaySUSEthEtEthERStRapwhENthEStROLLERiSiNUSE.
• thECORRECtUSEaNDMaiNtENaNCEOFthiSVEhiCLEaREESSENtiaL.
• BESUREthataLLCLaMpSaNDBUCkLESaRESECURELyFixEDaNDiNpLaCEBEFOREUSE
• whENiNthEStROLLER,yOURChiLDMUStaLwaySwEaRthESaFEtyhaRNESS,CORRECtLyFittEDaNDaDjUStED,at
aLLtiMES.
•NEVERExCEEDthEMaxiMUMwEightORhEightOFthEChiLDFORwhiChyOURCaRSEatiSiNtENDED-REFERtOyOUR
CaRSEatMaNUaLFORiNFORMatiONREgaRDiNgthEwEightaNDhEightFORwhiChthESEatCaNBEUSED.
• REFERtOyOURCaRSEatMaNUaLFORUSagEiNStRUCtiONS
• NEVERRUNwithaNEwBORNBaByiNaNypRaMORStROLLER.
• ChECkaLLpaRtSBEFOREUSEFORBREakagEORFatigUE.DiSCONtiNUEUSEiMMEDiatELyiFaNypaRtiSFOUNDtOBE
DaMagEDORBROkEN.
• MaxiMUMLOaDOFBaSkEtS:3.5kgS.
• aLwaySBEawaREOFthERiSkSpROViDEDByFiREaNDOthERSigNiFiCaNtSOURCESOFhEatSUChaSRaDiatORS,
EtC.whiChMayBEiNthEiMMEDiatEViCiNityOFyOURStROLLER.
•itMayBEUNSaFEtOUSEaNyaCCESSORiESOthERthaNVaLCOappROVEDONES.
• thiSpRODUCtiSiNtENDEDFORDOMEStiCUSEONLy.itiSNOtiNtENDEDFORCOMMERCiaLUSE.
Should the chassis become wet, dry off promptly before storing. If this pram is used near the ocean or salted
roads, spray the chassis and seat frame with water and dry. We recommend a rust inhibiting product should
be used to prevent rust and fatigue on metal parts.
We recommend that you wipe down axles and lubricate the wheels every 3 months. Sand and dirt can grind
down axles, if you live near the beach or in a dusty environment you must wipe down the axles and wheels
then lubricate them monthly.
AXLES ARE BEST LUBRICATED WITH GREASE OR PETROLEUM JELLY. MOVING PARTS ARE BEST LUBRICATED
WITH SILICONE BASED PRODUCTS. DO NOT USE OIL BASED PRODUCTS.
In Australia/New Zealand
www.valco.com.au
In North America only
www.valcobaby.com
1 800 610 7850