Valley Comfort Systems VC95C User manual

Version 1.02 1 Date Printed: February 15, 2008
VC95C
SOLID FUEL-FIRED HEATER
INSTALLATION AND OPERATION MANUAL
READ THOROUGHLY AND COMPLY WITH ALL
LOCAL CODES AND REGULATIONS
VALLEY COMFORT SYSTEMS INC.
1290 COMMERCIAL WAY
PENTICTON B.C. V2A 3H5
250-493-7444
WWW.VALLEYCOMFORT.COM
EMAIL. [e-mail]
Pour la version française de nos manuels S.V.P. vous référez à notre site web: www.blazeking.com

Version 1.02 2 Date Printed: February 15, 2008
ASH REMOVAL 11
BAROMETRIC DAMPER 9
CLEARANCES 8
CREOSOTE CAUSES, REMOVAL & CONTROL OF 12
DOOR HANDLE ASSEMBLY 10
FAN CONTROL 8&9
FAN OPERATION 11
FIRE 11
FLUE PIPES 8
FUEL 9
HANDY HINTS 13
INSTALLAION INSTRUCTIONS 8
SPECIFICATIONS 9
SUMMER CARE 13
THERMOSTAT ADJUSTMENTS 10
WARRANTY 4-7
INDEX

Version 1.02 3 Date Printed: February 15, 2008
Welcome to the discriminating group of Canadian home owners who have
selected Valley Comfort heating units to satisfy their home heating needs.
The product you purchased was made by skilled craftsmen who have
given the company forty years of experience providing domestic heating
appliances. Your heating unit has been tested by a certified independent
testing laboratory to meet rigorous safety standards
This booklet contains the operating and installation instructions. If the
installation instructions are not followed, you will not be getting the best
results from your unit and Valley Comfort cannot honor its warranty.
"SAFETY NOTICE: FOR YOUR SAFETY, FOLLOW THE
INSTALLATION DIRECTIONS. IF THIS HEATER IS NOT
PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT.
CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT
RESTRICTIONS AND INSTALLATION INSPECTION
REQUIREMENTS IN YOUR AREA.”

Version 1.02 4 Date Printed: February 15, 2008
Warranty
BLAZE KING WOOD LIMITED WARRANTY
Blaze King and its respective brands extend the following warranty for wood fired appliances purchased from an
authorized Blaze King dealer and installed in the United States of America or Canada. Warranty starts with date
of purchase by the original owner (End User) except as noted for replacement parts.
Warranty Period Components
Covered
Parts Labor Wood
1 Year XAll parts, materials and surface finishes (flaking and peeling) Subject to Conditions,
Exclusion, and Limitations listed
2 Years XFan assemblies and motors, thermal sen- sors, catalytic thermometer , bi-metallic
thermostat assembly
5 Years 2 Year
X
Firebox & Heat Exchanger, Bypass Door
Steel Components
6 Years
X
Catalyst Combustor ( see Conditions, Ex-
clusions, and Limitations)
1 Year
X
Other Replacement Parts
See Conditions, Exclusions, and Limitations.

Version 1.02 5 Date Printed: February 15, 2008
Blaze King Wood Limited 5 Year Warranty
Blaze King is the manufacturer of the Blaze King line of heating products. At Blaze King, our commitment to the
highest level of quality and customer service is the most important thing we do. Each Blaze King stove is built on a
tradition of using only the finest materials and is backed by our limited warranty to the original purchaser. With
Blaze King, you’re not just buying a stove; you’re buying a company with years of unequalled performance and
quality.
Limited Six (6) Year Warranty:
The CATALYTIC COMBUSTOR is under warranty by Blaze King for six (6) years from the date of original retail
purchase. The purchaser shall pay the following share of the then current retail price for the combustor: The first
three (3) years no charge, 4th year 60%; 5th year 70%, 6th year 80%. The Combustor must be returned to your
dealer along with a completed COMBUSTOR FAILURE REPORT and original proof of purchase document.
Limited (5) Year Warranty:
Under this warranty, Blaze King covers the stove body and accessories against defects in materials and
workmanship, for part repair or replacement for the first five (5) years *** to the original purchaser. This Warranty
covers: All Steel firebox components against defects in material and workmanship. Please see the exclusions and
limitation section below as certain restrictions and exclusions apply to this warranty.
Limited Two (2) Year Warranty:
Under this warranty, Blaze King covers, fan assemblies and modular thermostat against defects in materials and
workmanship, for part repair or replacement and limited labor for the first two (2) years to the original purchaser.
Please see the exclusions and limitation section below as certain restrictions and exclusions apply to this warranty.
Limited One (1) Year Warranty:
Under this warranty, Blaze King covers all parts and materials against defects in materials and workmanship
including exterior paint finishes, for part repair or replacement and limited labor for the first year to the original
purchaser. Please see the exclusions and limitation section below as certain restrictions and exclusions apply to this
warranty.
How the Warranty Works
1. All warranties by the manufacturer are set herein and no claim shall be made against the manufacturer on any
oral warranty or representation. All claims under this Limited Warranty must be made in writing by your dealer.
2. Any stove or part thereof that is repaired or replaced during the Limited Warranty period will be warranted under
the terms of the Limited Warranty for a period not exceeding the remaining term of the original Limited Warranty or
six (6) months, whichever is longer.
3. For any part or parts of this stove, which in our judgment show evidence of defects, Blaze King reserves the
option to repair or to replace the defective part(s) through an accredited distributor or agent, provided the defective
part is returned to the distributor or agent, transportation prepaid, if requested.
4. If you discover a problem that you think may be covered by the Limited Warranty, you MUST REPORT it to your
Blaze King dealer WITHIN 30 DAYS from the date the problem was first detected, giving them proof of purchase and
the date of purchase. The dealer will investigate the problem and work with Blaze King to determine whether the
problem:
a) Is covered by the Limited Warranty or
b) Can be fixed in your home or does the product need to be returned to Blaze King for repair.
5. If Blaze King determines that the stove needs to be returned to Blaze King for repair, the customer has the
responsibility and the expense of removing it from their home and shipping it to Blaze King. If the problem is
covered by the Warranty, Blaze King will repair or replace the item at their discretion and the customer will be
responsible for return shipping and re-installation in their home.
6. If the problem is not covered by the Limited Warranty, the customer will be responsible for all repair costs, as
well as all storage, shipping and the cost of removing and re-installing the stove.
If you are not satisfied with the service provided by the Blaze King dealer, write to Blaze King at the address listed
on the last page of the Owner’s Manual. Include a copy of the original purchase invoice and a description of the
problem.

Version 1.02 6 Date Printed: February 15, 2008
Exclusions and Limitations:
1. This Warranty does not cover tarnish, discoloration or wear on the plated surfaces Painted finishes will change
colour after initial firing and will continue to change through the lifetime of the stove. This is normal occurrence for
all high temperature coatings.
2. This Warranty does not cover gasket material or firebrick.
3. Blaze King strongly recommends installation by a certified installer. Failure to comply may adversely affect
coverage under the terms of this warranty. This Limited Warranty covers defects in materials and workmanship only
if the product has been installed in accordance with local building and fire codes; in their absence refer to the
owner’s manual. If the product is damaged or broken as a result of any alteration, wilful abuse, mishandling,
accident, neglect, or misuse of the product, the Limited Warranty does not apply.
4. The stove must be operated and maintained at all times in accordance with the instructions in the Owner’s
Manual. If the unit shows signs of neglect or misuse, it is not covered under the terms of this Warranty policy.
Performance problems due to operator error will not be covered by the Limited Warranty policy.
5. Some minor expansion, contraction, or movement of certain parts and resulting noise, is normal and not a defect
and, therefore, is not covered under this Limited Warranty.
6. Misuse includes over-firing. Over-firing can be identified later by warped plates and paint pigment being burnt off.
Over-firing this appliance can cause serious damage and will nullify the Limited Warranty.
7. The Limited Warranty will cover glass thermal breakage only and will not cover misuse of the stove glass,
including but not limited to:
a) Glass that is struck, has surface contaminates or has had harsh or abrasive cleaners used on it.
b) If the door is slammed or is closed while wood in the firebox is protruding out the stove opening thus striking the
glass.
8. This warranty does not cover products made or provided by other manufacturers and used in conjunction with the
operation of this stove without prior authorization from Blaze King The use of such products may nullify the Limited
Warranty on this stove. If unsure as to the extent of this Limited Warranty, contact your authorized Blaze King
dealer before installation.
9. Blaze King will not be responsible for inadequate performance caused by environmental conditions.
10. The Limited Warranty does not cover installation and operational related problems such as use of downdrafts or
spillage caused by environmental conditions. Environmental conditions include but are not limited to nearby trees,
buildings, roof tops, wind, hills, mountains, inadequate venting or ventilation, excessive offsets, negative air
pressures or other influences caused by mechanical systems such as furnaces, fans, clothes dryers etc.
11. The Limited Warranty does not cover damage caused by burning salt-saturated wood, corrosive driftwood,
chemically treated wood or any fuel not recommended in the Owner’s Manual (use cord wood only).
The Limited Warranty is void if:
a) The stove has been operated in atmospheres contaminated by chlorine, fluorine or other damaging chemicals.
b) The stove is subject to submersion in water or prolonged periods of dampness or condensation.
c) Any damage to the unit, combustion chamber or other components due to water, or weather damage which is the
result of, but not limited to, improper chimney/venting installation.
d) Salt air in coastal areas or high humidity can be corrosive to the finish; these environmental conditions can cause
rusting. Damage caused by salt air or high humidity is not covered by the Limited Warranty.
12. Exclusions to the Limited Warranty include: injury, loss of use, damage, failure to function due to accident,
negligence, misuse, improper installation, alteration or adjustment of the manufacturer’s settings of components,
lack of proper and regular maintenance, alteration, or act of God.
13. The Limited Warranty does not cover damage caused to the stove while in transit. If this occurs, do not operate
the stove and contact your courier and/or dealer.
14. The Limited Warranty does not extend to or include paint, door or glass gaskets or firebricks damage caused by
normal wear and tear, such as paint discoloration or chipping, worn or torn gaskets, chipped or cracked firebrick,
etc.
15. The Limited Warranty does not include damage to the unit caused by abuse, improper installation, or
modification of the unit.
16. Damage to plated surfaces caused by fingerprints, scratches, melted items, or other external scores and
residues left on the plated surfaces from the use of abrasive cleaners or polishes is not covered in this warranty.
17. Blaze King is free of liability for any damages caused by the stove, as well as inconvenience expenses and
materials. The Limited Warranty does not cover incidental or consequential damages.
18. The Limited Warranty does not cover any loss or damage incurred by the use or removal of any component or
apparatus to or from the Blaze King stove without the express written permission of Blaze King and bearing a Blaze
King label of approval.
19. Any statement or representation of Blaze King Products and their performance contained in Blaze King
advertising, packaging literature, or printed material is not part of the Limited Warranty.
20. The Limited Warranty is automatically voided if the stove’s serial number has been removed or altered in any
way. If the stove is used for commercial purposes, it is excluded from the Limited Warranty.

Version 1.02 7 Date Printed: February 15, 2008
21. No dealer, distributor, or similar person has the authority to represent or warrant Blaze King Products beyond
the terms contained within the Limited Warranty. Blaze King assumes no liability for such warranties or
representations.
22. Blaze King will not cover the cost of the removal or re-installation of the stove, hearth, facing, mantels, venting
or other components.
23. Labor to replace or repair items under this Limited Warranty will be covered per our warranty service fee
reimbursement and labor rates are set per component schedule. Labor rates vary from location to location and as
such total labor costs may not be covered. Please consult with your dealer or service technician for any additional
charges such as travel time or additional labor charges that may apply.
24. For parts of the Blaze King woodstove or fireplace insert warranted beyond the first year, the five year limited
warranty will have the same obligations as described in this document, provided, however that the purchaser shall
pay the following percentage of the then current retail cost of the repair or the replacement, according to the year
after purchase in the which the defect is brought to the attention of Blaze King.*** During the 2nd year----purchaser
pays 20%.
3rd year ----purchaser pays 40%. 4th year -----purchaser pays 60%. 5th year---- purchaser pays 80%.
25. If a defect or problem is determined by Blaze King to be non warrantable, Blaze King is not liable for travel costs
for service work. In the event of in-home repair work, the customer will pay any in-home travel fees or service
charges required by the Authorized Dealer.
26. At no time will Blaze King be liable for any consequential damages which exceed the purchase price of the unit.
Blaze King has no obligation to enhance or modify any stove once manufactured (example: as a stove model
evolves, field modifications or upgrades will not be performed).
27. This Limited Warranty is applicable only to the original purchaser and it is non-transferable.
28. This warranty only covers Blaze King Products that are purchased through an authorized Blaze King dealer.
29. If for any reason any section of the Limited Warranty is declared invalid, the balance of the warranty remains in
effect and all other clauses shall remain in effect.
30. The Limited Warranty is the only warranty supplied by Blaze King, the manufacturer of the stove. All other
warranties, whether express or implied, are hereby expressly disclaimed and the purchaser’s recourse is expressly
limited to the Limited Warranty.
31. Blaze King and its employees or representatives will not assume any liability for damages, either directly or
indirectly, caused by improper usage, operation, installation, servicing or maintenance of this stove.
32. Blaze King reserves the right to make changes without notice. Please complete and mail the warranty
registration card and have the installer fill in the installation data sheet in the back of the manual for warranty and
future reference.
33. Blaze King is responsible for stocking parts for a maximum of seven (7) years after discontinuing the
manufacture or incorporation of the item into its products. An exception to this would be if an OEM supplier is not
able to supply a part.

Version 1.02 8 Date Printed: February 15, 2008
INSTALLATION INSTRUCTIONS
EXAMINE THE SHIPMENT
Please inspect this shipment as soon as it arrives. If you discover any parts missing, or any damage, have the carrier make an
inspection immediately and make a notation on the freight bill. Should you discover damage after unpacking the crate notify the carrier
and have him inspect the heater within fifteen days. Send the inspection report, freight bill and your explanation of the damage to your
local Valley Comfort dealer. You will be advised on what parts will be replaced.
MINIMUM INSTALLATION CLEARANCE
It is of great importance that all combustible materials, including firewood, be kept a safe distance from this heater. The minimum
distances should be:
Top of the Heater . ................................. 48"
Wood Charging End .................................. 48"
Rear of Heater .................................. 24"
Front of Heater .................................. 36"
Other Side .................................. 12"
Flue Pipe .................................. 18"
If the heater is being installed on a combustible floor, a regulation insulating sheet metal covered stove board should be placed under
it. This board should extend at least 18" beyond the heater on the wood charging side and 6" on all other sides.
INSTALLATION
Valley Comfort Systems Inc. supports the Wood Energy Technology Transfer Inc. this organization provides training and
certification for personnel involved in installation and maintenance of wood heating systems across Canada. For your safety
and satisfaction your system must be properly installed.
The installation of this heater shall be in accordance with the regulations of authorities having jurisdiction. It shall be installed where
there is an adequate supply of combustion air to assure proper combustion. If necessary, provisions must be made to compensate for
air drawn by other appliances, such as exhaust fans, clothes dryers or fireplaces.
If the heater is being installed where normal air infiltration does not meet the requirements for combustion and ventilating, outside air
must be introduced to the heater area.
THE FLUE PIPE
The Flue pipes used should be 6" in diameter and constructed of uncoated steel sheet metal or stainless steel with a thickness of at
least 24 gauge. Always fit the small crimped end of the pipe into the large section of the pipe below, beginning with the small end of
the flue pipe fitting into the flue collar on the heater. This will allow any creosote that may form in the pipe to run back in to the
combustion chamber and burn safely, rather than run out the joints and onto the floor.
Avoid long horizontal runs when installing the flue pipe. It is best if you can obtain at least 1/4 rise per foot to the chimney. If possible
avoid using more than two elbows between the chimney and the heater.
Fasten all pipe joints, including the heater flue collar, with sheet metal screws. Use a bolt on the heater flue collar. On long pipe
installations the joints should be sealed with furnace cement.
THE FAN COMPLETE WITH CONTROL
Study the diagram on the next page. Then attach the control with the two screws provided, as shown at "A". Adjust it by moving it to
and from the smoke pipe. Moving the control towards the smoke pipe will allow a fast cut-in of the fan, away will provide slower cut-in.
The average setting is from 3/4" to 1" from the smoke pipe to the center of the control.
Attach the fan with the four 1/4 x 1/2 bolts provided, making certain that the oiling holes on the motor are facing up. Using a light oil
(SAE 20/30), oil the motor at each end of the shaft once a season or every six months when in use. If the fan motor is a sealed
bearing type there are no holes, no oiling is required.

Version 1.02 9 Date Printed: February 15, 2008
ATTACHING A FAN CONTROL ON THE THERMOSTATIC WOOD HEATER
BAROMETRIC DAMPER & CHIMNEY
If your heater is being connected to a chimney with a consistently high draft install a barometric draft regulator set
at .03 inches water column. Do not use a turn damper.
It is recommended that you connect the heater to a nominal 8" x 8" tile lined masonry chimney, which is in good
repair, and free from any leaks or obstructions. Alternately, a 6" diameter prefabricated chimney approved for solid
fuel can be used.
NOTE: Care should be taken to prevent the products of combustion, in the flue pipe which may contain carbon
monoxide, from entering the room where the heater is installed.
Particular care should be paid to the joints to ensure that there are no leaks from the flue pipe.
SPECIFICATIONS MODEL VC95C
Overall Size 34 1/2" wide x 22 1/4" deep x 35" high
Size of Pipe Collar 6"
Size of Fuel Door 10" x 11"
Length of Wood Used 24"
Capacity 4 cubic feet

Version 1.02 10 Date Printed: February 15, 2008
ASSEMBLY OF DOOR HANDLE
The door handle should be assembled as shown in the diagram below.
OPERATING YOUR HEATER
Before firing your new Valley Comfort heater - spread an inch of sand or ashes over the floor of the combustion
chamber. This will reduce any danger of warping due to overheating.
Next. Turn the control knob of the regulator or thermostat to a medium position. This opens the draft damper at the
base of the heater.
Place crumpled newspapers in the heater and cover them with kindling and small pieces of wood. Ignite this and,
as the fire grows, add larger pieces of wood.
Do not be alarmed by fuming or smoke the first time you use your heater. This is caused by the high temperature
paint which is simply curing. You may wish to open a few windows to clear the air.
MAKING ADJUSTMENTS
When your home reaches the desired temperature, turn down the knob on the regulator until the large draft damper
closes. The small pilot damper will stay open and the temperature should remain the same without anymore
adjustments, until the fuel level becomes low. With the heater at room temperature and the control knob at the 2.5
setting, adjust the damper chain (if necessary) so that the damper just closes.
When the outside temperature changes suddenly, you may find it necessary to turn the control knob to obtain more
or less heat. We suggest that you turn the knob no lower than one position at night or you will use more fuel trying
to reheat the house in the morning.
When loading the heater keep the wood level beneath the bottom of the wood charging door.

Version 1.02 11 Date Printed: February 15, 2008
USING THE PROPER FUEL
A dry seasoned hardwood will produce the greatest amount of heat and the least amount of creosote. Using green wood results in
heat loss due to the evaporation of the excess moisture content. This decreases efficiency and can cause a creosote build-up.
Check your flue pipes and chimney periodically during the heating season and clean them if necessary.
ADDING FUEL
It is best to add fuel when the previous load has been converted to charcoal, as there is very little smoke at this stage. Rake the ashes
lightly to uncover pieces of charcoal trapped where they will not burn. Add a few small pieces of wood to the fire, than larger logs.
Weather conditions will determine the firing rate.
DURING MILD WEATHER
When the temperature is warmer you only need to add enough of the driest wood available to last four to six hours. This will cut down
on the amount of fuel you use. DO NOT use green or wet wood, as the moisture in it will cause the heater to smolder and deposit
creosote in the flue and chimney. It is wisest to use small pieces of wood and turn the thermostat control knob up at least once a day
for long enough to burn off any creosote which may have built up overnight in a slow fire (about 15 minutes).
REMOVING THE ASHES
When the ashes are within two inches of the bottom of the louvers on each corner of the inside side liners, they must be removed. A
shovel is provided for this purpose. Leave about one inch of ashes in the chamber to prevent warping.
This heater has an over fire air duct which allows entry of preheated secondary combustion air over the fire. This ensures complete
burning of the gases and minimizes the incidence of creosote in the flue pipe and chimney.
USING THE FAN/BLOWER
The ten inch circulating fan with automatic fan control is an optional feature. This single speed blower has a 400 CFM capacity to
circulate the warm air into hard to heat places.
Twice a year you should oil the motor with a few drops of motor oil (SAE 20/30) Be careful not to over oil it. If your fan is a sealed
bearing type, no oiling is required.
UNCONTROLLED FIRES
Uncontrolled fires can be caused by too much fuel, opening the combustion air damper too far, or too much flue draft. Should this
occur: CALL THE FIRE DEPARTMENT! DO NOT REMOVE THE FLUE PIPES UNTIL THE FIRE IS COMPLETELY EXTINGUISED!
IMPORTANT: This heater was designed to burn only wood.
DO NOT burn coal, gasoline, kerosene, engine oil, garbage,
chemical fire starters, manufactured logs or painted wooden
boards. This could result in extremely high temperatures or
an explosion.
DO NOT use salt water driftwood as it will corrode the heater
and will void any warranty.

Version 1.02 12 Date Printed: February 15, 2008
CREOSOTE
Creosote can be a problem with any type of wood burning equipment so it is important to know what it is and how to avoid it.
Creosote is an oily or tarry liquid resulting from the distillation of wood during the process of combustion. It is present in the gases
given off all types of burning wood, and in its solid and semi-liquid state is highly combustible.
When creosote forms on the inside of flue pipes and chimneys it can build up considerable thickness. As the creosote builds up, the
draft opening is reduced. When the build up is permitted to take place over an extended period of time, sufficient creosote may be
present in the stack to cause a serious fire if ignited. All users of automatic wood burning equipment should be thoroughly familiar
with the causes, control and cure of creosote. When automatic wood burning equipment is properly installed and used, the incidence
of creosote buildup is greatly reduced.
CAUSES OF CREOSOTE FORMATION
Creosote is formed from flue gasses when the stack temperature drops below 250 degrees F (120 degrees C). The amount of
creosote deposited in the pipe and the chimney is affected by the amount of moisture in the flue gases, the temperature of the stack,
the amount of draft in the stack, and how completely the combustion elements in the flue gases have been consumed in the process
of combustion.
REMOVAL OF CREOSOTE
A:) When the flue pipe and chimney become coated due to improper burning conditions, the only practical way of cleaning is to
disassemble the pipe and scrape the inside of the chimney..
The best way to remove creosote from the chimney is with a two cone-shaped wire brush slightly larger than the chimney. As
they are pulled up the chimney, they scrape away the creosote.
B:) The small amounts of creosote that are normally deposited can be kept from accumulating by :
1. Opening the draft by turning up the thermostat for 20 or 30 minutes before adding fuel. This will increase the stack
temperature and cause any creosote in the pipe to dry. In the process of drying, the creosote shrinks, and the scale falls from
the inner wall of the pipe.
2. Remember a fast fire a day will keep creosote away. A small intense fire is preferable to a large smoldering one.
CONTROL OF CREOSOTE
A) Moisture in the flue gas can be kept low by:
1. Using the driest wood obtainable.
2. Mixing small pieces with every charge. These smaller pieces should be placed on the charcoal bed when adding fuel.
3. Not using only large wood during mild weather when combustion is relatively slow. Add small pieces.
4. Always using dry, split wood in mild weather.
5. Never adding more than a 12 hour supply of wood at one time.
B) The temperature of the stack can be increased to reduce creosote formation by:
1. Insulating smoke pipe extensions so that they will be cooled as little
as possible before reaching the chimney.
2. Using an insulated chimney
C) The amount of draft in the stack can be controlled by:
1. Having as few elbows as possible
2. Insuring adequate height and diameter
3. Preventing any air leaks
4. Eliminating any external obstructions at the chimney outlet.
D) The rate at which the wood is burned is dependent upon the seasons and your heating requirements.
Creosote deposits are more apt to occur during mild weather when the draft damper is closed, and the wood just sits in the
firebox smoldering. During mild weather when little heat is required feed only enough dry wood to last four to six hours.

Version 1.02 13 Date Printed: February 15, 2008
SUMMER CARE
After your last fire of the season, remove the ashes from your heater and clean it thoroughly inside and out.
Handy Hints
Using cotton gloves when tending the heater will keep your hands clean and prevent any small burns.
Place an open newspaper on the floor in front of the heater to protect the floor covering when adding fuel.
Smoke discharging into the room when the fuel charging door is opened usually indicates that the previous
charge has not completely burned or that there is insufficient draft in the chimney.
If your heater is attached to a good chimney with adequate draft and is operated according to our instructions
you should have years of trouble free comfort.
If, however, you do experience any trouble contact your Valley Comfort dealer. They will need to know the kind
of wood you've been burning, the average size of pieces, the type, condition and size of the flue and whether it is
tile lined. Sketch the heater and flue pipe hook-up to the chimney.
NOTE: Products of combustion can contain carbon monoxide,
especially when the fire is smoldering and starving for air.
To prevent this, do no close the damper too tightly.

Version 1.02 14 Date Printed: February 15, 2008