Valor LIMOUSIN BR627 User manual

600B607/05
OWNER’S GUIDE
AS SUPPLIED, THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20)
WHEN CONVERTED USING VALOR CONVERSION KIT NO.591159 THIS
APPLIANCE IS FOR USE WITH PROPANE GAS (G31)
THIS APPLIANCE IS FOR USE IN THE UNITED KINGDOM (GB) AND THE
REPUBLIC OF IRELAND (IE) ONLY.
This guide is intended to help you care for your Valor gas fire. Please read
thoroughly before using and keep for future reference
We trust that this guide gives sufficient details to enable the your appliance to be
operated and maintained satisfactorily. However, if further information is required,
our Valor AdviceLine will be pleased to help.
Please telephone [phone] (Local call rates apply).
This guide to be left with the owner
© Valor Heating
COALFLAME
&
LIMOUSIN
MODEL BR627
(GC No. 32-032-22)
INSET LIVE FUEL EFFECT
GAS FIRE

OWNER’S GUIDE
Page 2
Safety First.
Valor fires are CE Approved and designed to meet the appropriate British Standards
and Safety Marks.
Quality and Excellence at the heart of every Valor fire.
All Valor fires are manufactured to the highest standards of quality and excellence
and are manufactured under a BS EN ISO 9001 quality system accepted by the
British Standards Institute.
The Highest Standards
Valor is a member of the Society of British Gas Industries which works to ensure
high standards of safety, quality and performance.
Careful Installation
Valor is a CORGI registered company. All our gas fires must be
installed by a competent CORGI Registered Installer in accordance
with our Installer Guide and should not be fitted directly on to a
carpet or floor of combustible material.
Valor Heating, Erdington, Birmingham B24 9QP
Because our policy is one of constant development and improvement, details may
vary slightly from those given in this publication

OWNER’S GUIDE
Page 3
LIST OF CONTENTS
SAFETY........................................................................................................................ 4
OPERATING YOUR FIRE.......................................................................................... 6
CLEANING................................................................................................................... 8
FITTING THE CERAMIC COALS............................................................................. 9
MAINTENANCE........................................................................................................ 10
CUSTOMER CARE
Thank you for choosing Valor.
All Valor gas fires are designed to meet the most stringent quality, performance and
safety requirements to provide our customers with many years’ trouble-free service.
Your owner guide aims to improve your understanding and appreciation of your
Valor gas fire by providing simple and informative instructions to ensure that you
benefit from the excellent performance and features it has to offer.
If you require further assistance or any advice about gas in general,
the Valor AdviceLine will be pleased to help.
Please telephone [phone] (local call rates apply in the United Kingdom).

OWNER’S GUIDE
Page 4
SAFETY
IF YOU SMELL GAS
DON’T SMOKE
EXTINGUISH ALL NAKED FLAMES
DON’T TURN ELECTRICAL SWITCHES ON OR OFF
TURN OFF THE GAS SUPPLY AT THE METER
OPEN DOORS AND WINDOWS TO GET RID OF THE GAS
IMMEDIATELY CALL THE GAS EMERGENCY SERVICE – SEE YOUR
LOCAL TELEPHONE DIRECTORY
1. As with any gas appliance, this fire
must be installed by a competent
person (in the United Kingdom
registered with CORGI).
In the United Kingdom, installation
must be in accordance with the
latest edition of the Gas Safety
(installation & use) Regulations.
In the Republic of Ireland,
installation must be in accordance
with all national and local
regulations in force.
2. If the fire is intended to be installed
to a chimney which was previously
used for solid fuel, the chimney must be swept prior to installation.
3. The fire must not stand on carpets or other combustible materials. The fire must
stand behind a non-combustible hearth surface. The hearth material must be at
least 12mm thick. Its top surface should be 50mm above floor level to discourage
placing carpets, rugs or other combustible materials over it. The minimum size of
the hearth is shown in figure 1.
4. If the fire is intended to be installed against a wall with combustible cladding, the
cladding must be removed from the area covered by the outer surround.
Figure 1 Hearth minimum dimensions

OWNER’S GUIDE
Page 5
5. The minimum height from the top of the
hearth to the underside of any shelf made
from wood or other combustible material
and which is not more than 150mm deep is
750mm.
For shelves deeper than 150mm add
12.5mm to the above clearance for every
25mm of additional shelf depth.
See figure 1a.
6 The minimum allowable distance to a
corner wall or other combustible projection
from the outside edge of the front surround
at either side is 100mm. See figure 1a.
7. Never put any paper or other material on
the fire. Never add any extra coals above
the number stated in these instructions.
This could cause a safety hazard.
8. It should be appreciated that although this
appliance conforms to all the applicable
standards, it is a decorative fuel effect
heating appliance and certain parts of its
surface will become hot. A suitable guard which complies with BS 6539 or 6778
should be used for the protection of young children, the elderly and the infirm.
Such a guard is also recommended for the protection of pet animals.
9. Always switch the fire off and allow to cool before handling. Note that this
appliance retains heat for some time after it has been switched off.
10.Never hang clothing, towels or any other fabrics over the fire.
11.This appliance is fitted with an Oxysafe device which will automatically shut off
the supply of gas to the fire if, for any reason, the flames go out. If this device
does operate or if the fire is turned off accidentally or intentionally, always wait
three minutes before attempting to relight.
12.Soft wall coverings (e.g. embossed vinyl etc.), are easily affected by heat. They
may, therefore, scorch or become discoloured when close to a heating appliance.
Please bear this in mind when having a heating appliance installed and when
redecorating.
13.Never add any extra coals above the number stated in this guide. This could cause
a safety hazard.
Figure 1a Front dimensions &
clearances
(
Shown with Coalflame front
)

OWNER’S GUIDE
Page 6
OPERATING YOUR FIRE
Please note
•When operating your fire for the first time, some vapours may be given off which
may cause a slight odour and could possibly set off any smoke alarms in the
immediate vicinity. These vapours are quite normal with new appliances. They are
totally harmless and will disappear after a few hours use.
•This fire is supplied with ceramic “coals” to simulate a real coal fire. After some
use, the coals may change colour. This is quite normal.
The Oxysafe flame sensing & flue blockage safety system.
For your safety, this appliance is fitted with a flue blockage safety device which will
shut down the appliance in the event of abnormal flue conditions. This device is NOT
a substitute for an independently mounted Carbon Monoxide detector.
The device will also automatically shut off the gas supply to the fire if the pilot flame
goes out due to lack of oxygen or for any other reason.
If this device starts to repeatedly shut off the gas, get expert advice.
This device incorporates a probe which senses that the heat from the pilot flame is
correct. If this probe is cool, the device will prevent any gas flow unless the sliding
control button is held at the ignition position.
If, for any reason, the flames go out when the fire is hot or if the fire is turned off
when hot, always wait at least three minutes before attempting to relight.
To light the fire
The control is shown in figure 2.
1. Slide the control button to the bottom (ignition)
position marked ✩
✩✩
✩In this position, the electronic
ignition system should cause a series of sparks which
should light the pilot. Within four seconds of the
pilot igniting, the main burner should light at its
minimum setting.
If no sparks are produced to light the pilot, the
battery may need replacing. Details of battery
replacement are given on page 10.
Until you can obtain a replacement battery the fire
can be lit with a taper as described on page 7.
2. Keep the button at the ignition position for a further ten seconds. This will
prevent the flame sensing device from shutting off the gas while its probe warms up
as explained above.
Fig. 2 control

OWNER’S GUIDE
Page 7
3. If low heat is required, release the button. The button will automatically spring
up to the low heat position shown in figure 2
(See note i below).
4. For a higher heat level slide the button upwards. The burner flames and heat
output will gradually increase until the button reaches the high heat position shown in
figure 2. When the button reaches the high heat position you will feel a check to its
movement. Do not slide the button above the high heat position unless you want to
turn the fire off (See note i below).
Note
i) If the flames go out while setting the control, repeat the full lighting procedure. If
the flames repeatedly go out have the fire serviced.
ii) Please note. When first turned on the flames will appear predominantly blue. The
coals will take time to warm up. Although some glow will be seen after
approximately ten minutes, the full visual effect will only be apparent after a
somewhat longer time.
iii) The appliance will operate to its maximum potential if the flue is primed during
the first 20 – 30 minutes of operation.To do this, simply slide the control button to
its highest setting. This will also burn off any carbon deposits that may have
formed during previous operations.
iv) If operating the appliance for long periods it is beneficial occasionaly to change
the settings. This will also help to remove any carbon deposits that may form
during operation.
To turn the fire off
Slide the button up past the high heat position to the “O” position.
Both the main burner and the pilot should go out.
While cooling, the coals may make some crackling noises.
This is quite normal.
Lighting with a taper
In the unlikely event of failure of the ignition spark, the
pilot can be lit by a taper or long spill. Insert the taper or
spill alongside of the left side of the fire box and operate
the slide control as described above. See figure 3.
Fig. 3 Lighting with a
taper

OWNER’S GUIDE
Page 8
CLEANING
Turn the fire off and allow it to cool before attempting any cleaning. Note that the
fire will retain heat for some time after it has been turned off.
If large pieces of debris are found anywhere in the fireplace, have the chimney
inspected before further use.
Metal parts
Clean the metal parts with a slightly damp cloth and then dry. Do not use abrasive
cleaners, they could scratch the surface.
Ceramic Coals
This product uses a fuel effect pieces containing Refractory Ceramic Fibres (RCF),
which are man-made vitreous silicate fibres. Excessive exposure to this material may
cause temporary irritation to eyes, skin and respiratory tract. Consequently, it makes
sense to take care when handling these articles to ensure that the release of dust is
kept to a minimum.
Light coatings of soot will usually be burnt off during the normal operation of the
fire. Should any soot accumulation become excessive, the fuel effect pieces should be
removed from the fire for cleaning. Cleaning should be carried out in a well
ventilated area or in the open air by gently brushing with the pieces held away from
your face so that you avoid inhaling the dust. We do not recommend the use of a
normal domestic vacuum cleaner which may blow dust back into the air. We suggest
that you remove the coals in the reverse order to that shown in the ceramic coal
refitting instructions.
Ceramic burner
Remove any deposits of soot or other foreign matter from the solid areas of the
burner with a dry soft brush. Be careful not to brush any particles into the open slots.
Remove any particles from the slots with a vacuum cleaner fitted with a soft brush
attachment. Do not poke wire, etc. into the slots in the burner.

OWNER’S GUIDE
Page 9
FITTING THE CERAMIC COALS
7.1 Place the
front base coal
in the burner
compartment so
that it rests on
the ledges at the
sides and front. Pull the coal forward so
that it is immediately behind the front
rim of the burner compartment See
figure 4.
7.2 Place the
rear base
coal in the
burner
compartment
behind the
front coal. It
should rest
on the ledge
at the back
of the burner
compartment
The
projections
at the sides
of the rear coal should touch the front
coal. See
figure 5.
7.3 Place
one of the
loose coals
from the
bag in the
centre of
the front base coal. Make sure that it
bridges the space between the front and
rear base coals. See figure 6.
7.4 Place
two coals
each side
of the
centre
loose coal.
Make sure
that they
bridge the space between the front and
rear base coals. See figure 7.
7.5 Place
a loose
coal behind
the central
coal in the
front row
central and
resting on the two peaks of the rear
base coal. See figure 8.
7.6 Place
two coals
each side
of the
centre
loose coal
and
immediately behind the front row of
coals. See
figure 9.
7.7 Place
two of the
remaining
coals each
side of the
central peak at the rear of the base coal
and immediately behind the second row
of coals. See figure 10.
Fig.10
Fig. 9
Fig. 8
Fig. 7
Fig. 6 First loose coal
Fig. 5 Rear base coal
Fig. 4 Front base coal

OWNER’S GUIDE
Page 10
MAINTENANCE
Battery replacement
This appliance requires 9V PP3 Ever-Ready
Silver Seal (or equivalent) battery.
To replace the battery remove the bottom
front cover casting.
Fit the new battery firmly to the connections
on the generator, the positive battery
terminal (+) being to the right as you insert.
See figure 11.
Regular maintenance
In order to achieve and maintain high levels
of personal safety and performance efficiency, it is essential that the opening at the
back of the fire and the flue are kept clear of any form of obstruction. It is possible
that deposits of mortar or soot could fall and accumulate causing the flue to be
blocked or restricted and so preventing proper clearance of dangerous exhaust fumes.
In the United Kingdom it is the law that a landlord must have any gas appliance, flue
and pipework which is situated in a tenant’s premises checked for safety at least
every twelve months by a competent person (In the U.K, a CORGI registered
installer).
We recommend that all gas appliances and their flues, wherever situated, are checked
annually.
Fig. 11. Battery fitting
(The bottom front cover has been
removed for clarity)

OWNER’S GUIDE
Page 11
Servicing
•In the United Kingdom servicing can be carried out either by a Valor Service
engineer or a CORGI registered installer.
•If you require your fire to be serviced by a Valor engineer, please contact
Valor Service on 0121 386 6203 and quote the following details;
a) model name and number.
b) appliance serial no. (To be found below the burner and behind the bottom front
cover)
•If you wish to replace any of the owner replaceable parts listed below, please
contact Valor Sales on 0121 386 6260 for your nearest stockist of these parts.
When ordering please quote the part number shown below.
Owner Replaceable Parts
Description Part No
Rear base coal 565739
Front base coal 569579
Bag of 14 loose coals 563339
•When fitting replacement parts, follow the instructions contained in this
guide. It is important that only Valor approved parts are used for maximum
safety.
•In the United Kingdom, for general advice about gas and your gas fire call
the VALOR ADVICELINE 0345 626341.
•In the Republic of Ireland call 353 183 75114 for all enquiries.
This appliance was installed by:
Installer’s Company Name………………………………………………….
Telephone…………………………………………………………………….