VanGaa Lighting Swift 1915Z User manual

Swift1915Z Aura LED Moving Head Beam Wash Light User Manual Swift1915Z Aura LED Moving Head Beam Wash Light User Manual
Swift Aura LED Moving Head Zoom Light
Swift 1915Z
CE RoHS
User Manual
Please read this user manual before using this product！
Keep it for further reference!
http://www.vangaa.com

Swift1915Z Aura LED Moving Head Beam Wash Light User Manual Swift1915Z Aura LED Moving Head Beam Wash Light User Manual
INDEX
ⅠGENERAL.................................................................................................... 01
ⅡSAFETY INFORMATION.......................................................................... 02
ⅢOPERATION INSTRUCTIONS................................................................. 03
ⅣFEATURES AND SPECIFICATION.......................................................... 04
ⅤINSTALLATION AND CONNECTION..................................................... 05
ⅥOPERATION AND CONTROL ................................................................. 08
ⅦADDRESS SETTING AND DMX CHANNEL OPERATION.................. 18
ⅧTROUBLE SHOOTING.............................................................................. 22
ⅨMAINTENANCE AND CLEANING .......................................................... 23
ⅠGENERAL
Thank you for using our product! Please read this manual carefully and completely. For
technical reference in future, please keep this user manual well. This user manual contains
all installation and operation information of this Aura LED Moving Head Wash Light, it’s very
useful for user to install and operate the light. Please strictly abide by the relevant
instruction for the installation and operation.
This light has very beautiful appearance. Our Swift LED Moving Head is a very small and
smart light. But the brightness is very powerful. It owns very good light beam, and very
wonderful color mixing effect. As a SWIFT light, it’s small, but it runs extremely fast. This
light is very suitable for bar, disco, stage, theatre, decoration etc.
This light meets the following criteria:
GB7000.1-2007/IEC60598-1:2003
GB7000.217-2008/IEC60598-2-17:1984+A2:1990
Once receiving a fixture, carefully unpack the carton, check the contents to ensure that all
parts are presented, and have been received in a good condition. Notify the shipper
immediately and retain packing material for inspection if any parts appear damaged from
shipping or the carton itself shows, sign of mishandling. Save the carton and all packing
materials. In the event that a fixture must be returned to the factory, it is important that the
fixture be returned in the original factory box and packing.
Swift 1915Z---------1pc
Signal Cable---------1pc
Power Cable --------1pc
User Manual---------1pc
01

Swift1915Z Aura LED Moving Head Beam Wash Light User Manual Swift1915Z Aura LED Moving Head Beam Wash Light User Manual
ⅡSAFETY INFORMATION
※Important
Every person involved with the installation, operation and maintenance of this device has to
be qualified and follow the instructions of this manual. Manufacturer will not with
responsibility for those operations which are not according to this Instruction.
Verify that the voltage matches the rated voltage.
When the voltage is 110V , Do not connect more than 10 lightings in total to AC mains
power in one interconnected daisy chain
When the voltage is 220V , Do not connect more than 20 lightings in total to AC mains
power in one interconnected daisy chain
Before using the fixture, check that all power distribution equipment and cables are in
perfect condition and rated for the current requirements of all connected devices.
Always ground (earth) the fixture electrically.
Avoiding hit the Light when you are move or install the light.
The minimum distance between light-output and the illuminated surface must be
more than 0.5 meters. Keep all combustible materials (for example fabric, wood,
paper) at least 0.2 meters away from the fixture.
Do not expose the fixture to rain or moisture.
Avoid looking directly into the light source (especially those who suffer from epileptic
fits)
Maximum ambient temperature (Ta) is 40°C. Do not operate fixture at temperatures
higher than this.
The Maximum surface temperature is 50°C
When suspending the fixture above ground level, verify that the structure can hold at
least 10 times the weight of all installed devices.
Verify that all external covers and rigging hardware are securely fastened and use an
approved means of secondary attachment such as a safety cable.
To determine the power requirements for a particular fixture, see the label affixed
to the back plate of the fixture or refer to the fixtures specifications chart. A fixture listed
current rating is its average current draw under normal conditions. All fixtures must be
directly powered off a switched circuit and cannot be run off a rheostat
(variable resistor) or dimmer circuit, even if the rheostat or dimmer source voltage matches
the fixtures requirement. Check the fixture or device carefully to make sure that if a voltage
selection switch exists that it sets to the correct line voltage you will use.
Warning! Verify that the voltage select switch on your unit matches the line voltage
applied. Damage to your fixture may result if the line voltage applied does not match the
voltage indicated on the voltage selector switch. All fixtures must be connected to circuits
with a suitable Earth ground.
ⅢOPERATION INSTRUCTIONS
The moving head is an LED wash light for onsite decoration purpose.
Don’t turn on the fixture if it’s been through severe temperature difference like after
transportation because it might damage the light due to the environment changes. So
make sure to operate the fixture until it is in normal temperature.
This light should be keep away from strong shaking during any transportation or
movement.
Don’t pull up the light by only the head, or it might cause damages to the mechanical
parts.
Don’t expose the fixture in overheat, moisture or environment with too much dust
when installing it. And don’t lay any power cables on the floor. Or it might cause
electronic shock to the people.
Make sure the installation place is in good safety condition before installing the
-02-
03
02

Swift1915Z Aura LED Moving Head Beam Wash Light User Manual Swift1915Z Aura LED Moving Head Beam Wash Light User Manual
fixture.
Make sure to put the safety chain and check whether the screws are screwed properly
when installing the fixture.
Make sure the lens are in good condition. It’s recommended to replace the units if
there are any damages or severe scratch.
Make sure the fixture is operated by qualified personnel who knows the fixture before
using.
Keep the original packages if any second shipment is needed.
Don’t try to change the fixtures without any instruction by the manufacturer or the
appointed repairing agencies.
It is not in warranty range if there are any malfunctions from not following the user
manual to operate or any illegal operation, like shock short circuit, electronic shock,
lamp broke, etc.
ⅣFEATURES AND SPECIFICATION
◇Extremely small, fast and powerful LED moving beam.
◇DMX Channels: 14 channels mode
◇Operation modes: DMX512, Master/Slave
◇Great built-in lighting shows under Master/Slave mode
◇Blue LCD display for easy navigation
◇Perfect for stage, theatre, TV studio, rental and discotheques
Voltage: AC 100V~240V, 50/60Hz
Power consumption: 245W
LED: 19 X 12W RGBW LED
Dimension: 430X370X295mm
Weight: 9.2Kgs
Beam angel: 10°~60°
ⅤDIMENSION
Unit: mm
ⅤINSTALLATION AND CONNECTION
1. Installation
Be sure to install this product should be at least 0.5 m from the flammable materials
Screw one clamp each via a M12 screw and nut onto the Omega holders.
Insert the quick-lock fasteners of the first Omega holder into the respective holes on the
bottom of the device. Tighten the quick-lock fasteners fully clockwise. Install the second
Omega holder.
Pull the safety-rope through the holes on the bottom of the base and over the trussing
system or a safe fixation spot. Insert the end in the cabinet and tighten the safety screw.
Please refer to the picture below:
05
04

Swift1915Z Aura LED Moving Head Beam Wash Light User Manual Swift1915Z Aura LED Moving Head Beam Wash Light User Manual
1
23
PIN 3
PIN 2
120 Ω
2. DMX connection
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the
other side to the male 3-pin XLR input of the moving head. You can chain multiple Moving
head together through serial linking. The cable needed should be two core, screened cable
with XLR input and output connectors. Please refer to the diagram below.
Address 31 Address16 Address 1
DMX-512 CONNECTION WITH DMX TERMINATOR
For installations where the DMX cable has to run a long distance or is in an electrically noisy
environment, such as in a discotheque, it is recommended to use a DMX terminator. This
helps in preventing corruption of the digital control signal by electrical noise. The DMX
terminator is simply an XLR plug with a 120 Ω resistor connected between pins 2 and
3,which is then plugged into the output XLR socket of the last fixture in the chain. Please
see illustrations below:
07
06

Swift1915Z Aura LED Moving Head Beam Wash Light User Manual Swift1915Z Aura LED Moving Head Beam Wash Light User Manual
ⅥOPERATION AND CONTROL
1. Control panel
Display:
To show the various menus and the selected functions
LED:
POWER
ON
Power on
NULL
No function
NULL
No function
DMX
ON
DMX input present
Button:
MENU
To select the programming functions
DOWN
To go backward in the selected functions
UP
To go forward in the selected functions
ENTER
To confirm the selected functions
DMX input:
For DMX512 link, use 3/5-pin XLR cable to link the unit together.
DMX output:
For DMX512 link, use 3/5-pin XLR cable to link the unit together.
Mains input:
Connect to power supply.
Mains output:
Connect to supply power to the next unit.
Fuse (T 6.3A):
Protect the unit from damage of the over-current.
2. Main Functions
To select any of the given functions, press the MENU button up to when the required one is
showing on the display. Select the function by ENTER button and the display will blink. Use
DOWN and UP button to change the mode. Once the required mode has been selected,
press the ENTER button to setup, to go back to the functions without any change press the
MENU button again. Hold and press the MENU button about one second or wait for one
minute to exit the menu mode.
The main functions are showing below:
09
08

Swift1915Z Aura LED Moving Head Beam Wash Light User Manual Swift1915Z Aura LED Moving Head Beam Wash Light User Manual
DMX Functions
Enter MENU mode, select DMX Functions, press ENTER button to confirm, use UP
and DOWN button to select DMX Address, DMX Channel Mode or View DMX Value.
DMX Address
Select DMX Address, press ENTER button to confirm, the present address will blink
on the display, use UP and DOWN button to adjust the address from 1 to 512, press
ENTER button to store. Press MENU button back to the last menu or let the unit idle
one minute to exit menu mode.
View DMX Value
Select View DMX Value, press ENTER button to confirm. Channel function and its
value will show on the display, use UP and DOWN button to view other DMX value.
Press MENU button back to the last menu or let the unit idle one minute to exit menu
mode.
Fixture Setting
Enter MENU mode, select Fixture Setting, press ENTER button to confirm, then use
UP and DOWN button to select Pan Inverse, Tile Inverse, P/T Feedback,
BL.O. P/T Moving, White Balance, Cooling Mode or Dimmer Curve.
Pan Inverse
Select Pan Inverse, press ENTER button to confirm, present mode will blink on the
display, use UP and DOWN button to select No (normal) or Yes (pan inverse), press
ENTER button to store. Press MENU button back to the last menu or let the unit idle
one minute to exit menu mode.
11
10

Swift1915Z Aura LED Moving Head Beam Wash Light User Manual Swift1915Z Aura LED Moving Head Beam Wash Light User Manual
Tilt Inverse
Select Tilt Inverse, press ENTER button to confirm, present mode will blink on the
display, use UP and DOWN button to select No (normal) or Yes (tilt inverse), press
ENTER button to store. Press MENU button back to the last menu or let the unit idle
one minute to exit menu mode.
P/T Feedback —Pan/Tilt Feedback
Select P/T Feedback, press ENTER button to confirm, present mode will blink on the
display, press UP/DOWN button to select No (Pan or tilt’s position will not feedback
while out of step) or Yes (Feedback while pan/tilt out of step), press ENTER button to
store. Press MENU button back to the last menu or let the unit idle one minute to exit
menu mode.
BL.O. P/T Moving —Blackout while pan/tilt moving
Select BL.O. P/T Moving, Press ENTER button to confirm, present mode will blink on
the display, use UP and DOWN button to select No (normal while pan/tilt moving) or
Yes (blackout while pan/tilt moving), press ENTER button to store. Press MENU button
back to the last menu or let the unit idle one minute to exit menu mode.
White Balance
Select White Balance, press ENTER button to confirm, present mode will blink on the
display, use UP and DOWN button to select Red, Green or Blue, Once selected, press
ENTER button, then use UP and DOWN button to adjust the value from 125 to 255,
press ENTER button to store. Press MENU button back to the last menu or let the unit
idle one minute to exit menu mode.
Cooling Mode
Select Cooling Mode, press ENTER button to confirm, present mode will blink on the
display, use UP and DOWN button to select Auto (Normal) or Low (Low speed), Once
selected, press ENTER button to store. Press MENU button back to the last menu or
let the unit idle one minute to exit menu mode.
Dimmer Curve
Select Dimmer Curve, press ENTER button to confirm, present mode will blink on the
display, use UP and DOWN button to select Linear , Square Law, Inverse Squ. or
S-curve, Once selected, press ENTER button to store. Press MENU button back to the
last menu or let the unit idle one minute to exit menu mode.
Linear: The increase in light intensity appears to be linear as DMX value is increased.
Square Law: Light intensity control is finer at low levels and coarser at high levels.
Inverse Square Law: Light intensity control is coarser at low levels and finger at high
levels.
S-cure: Light intensity control is finger at low levels and high levels and coarser at medium
levels.
Display Setting
Enter MENU mode, select Display Setting, press ENTER button to confirm, use UP
and DOWN button to select Display Inverse, Backlight Auto Off,
13
12

Swift1915Z Aura LED Moving Head Beam Wash Light User Manual Swift1915Z Aura LED Moving Head Beam Wash Light User Manual
Backlight Intensity ,Temperature unit, Display Warning or Language.
Display Inverse
Select Display Inverse, press ENTER button to confirm, present mode will blink on the
display, use UP and DOWN button to select No (normal display) or Yes (inverse
display), press ENTER button to store. Press MENU button back to the last menu or let
the unit idle one minute to exit menu mode.
Backlight Auto Off
Select Backlight Auto Off, press ENTER button to confirm, present mode will blink on
the display, use UP and DOWN button to select No (display always on) or Yes (display
goes off one minute after exiting menu mode), press ENTER button to store. Press
MENU button back to the last menu or let the unit idle one minute to exit menu mode.
Backlight Intensity
Select Backlight Intensity, press ENTER button to confirm, present mode will blink on
the display, use UP and DOWN button to adjust backlight intensity from 1 (dark) to 10
(bright), press ENTER button to store. Press MENU button back to the last menu or let
the unit idle one minute to exit menu mode.
Temperature Unit
Select Temperature Unit, press ENTER button to confirm, present mode will blink on
the display, use UP and DOWN button to select ℃or ℉, press ENTER button to store.
Press MENU button back to the last menu or let the unit idle one minute to exit menu
mode.
Display Warning
Select Display Warning, press ENTER button to confirm, present mode will blink on
the display, use UP and DOWN button to select No (Normal) or Yes (display will show
the error warning when the unit went wrong). Press MENU button back to the last menu
or let the unit idle one minute to exit menu mode.
Language
Select Language, press ENTER button to confirm, present mode will blink on the
display, use UP and DOWN button to select English or Chinese. Press MENU button
back to the last menu or let the unit idle one minute to exit menu mode.
Fixture Test
Enter MENU mode, select Fixture Test, press ENTER button to confirm, use UP and
DOWN button to select Auto Test or Manual Test
Auto Test
Select Auto Test, press ENTER button to confirm, the unit will run built-in programs to
automatically test pan, tilt, color, gobo, shutter, dimmer, prism, red, green, blue, white,
CTC, frost, focus, and lamp on/off. Press MENU button back to the last menu or exit
menu mode after auto test.
Manual Test
Select Manual Test, press ENTER button to confirm, the present channel will show on
the display, use UP and DOWN button to select channel, press ENTER button to
confirm, then use UP and DOWN button to adjust the value, press ENTER button to
store, the fixture will run as the channel value indicates. Press MENU button back to
the last menu or exit menu mode let the unit idle one minute.
15
14

Swift1915Z Aura LED Moving Head Beam Wash Light User Manual Swift1915Z Aura LED Moving Head Beam Wash Light User Manual
(All channels value will become 0 after exiting Manual Test menu)
Fixture Information
Enter MENU mode, select Fixture Information, press ENTER button to confirm, use
UP and DOWN button to select Fixture use time, Lamp on time or Firmware Version.
Fixture use time
Select Fixture Use Time, press ENTER button to confirm, fixture use time will show on
the display, press MENU button to exit.
Lamp on time
Select Lamp on time, press ENTER button to confirm, lamp on time will show on the
display, press ENTER button to confirm, use UP and DOWN button to select Exit or
Reset Time, press ENTER button to confirm. Press MENU button back to the last
menu or exit menu mode let the unit idle one minute.
Firmware Version
Select Firmware Version, press ENTER button to confirm, firmware version will show
on the display, press MENU button back to exit.
Reset Functions
Enter MENU mode, select Reset Function, press ENTER button to confirm, use UP
and DOWN button to select Pan/Tilt, Zoom or All.
Pan/Tilt —Reset Pan/Tilt
Select Pan/Tilt, press ENTER button to confirm, use UP and DOWN button to select
Yes (the unit will run built-in program to reset pan and tilt to their home positions) or No,
press ENTER button to store. Press MENU button back to the last menu or let the unit
idle one minute to exit menu mode.
Zoom —Reset Zoom
Select Zoom, press ENTER button to confirm, use UP and DOWN button to select Yes
(the unit will run built-in program to reset Zoom to their home positions) or No, press
ENTER button to store. Press MENU button to exit.
All —Reset All
Select All, press ENTER button to confirm, use UP and DOWN button to select Yes
(the unit will run built-in program to reset all motors to their home positions) or No,
press ENTER button to store. Press MENU button to exit.
Special Functions
Enter MENU mode, select Special Functions, press ENTER button to confirm, use UP
and DOWN button to select Fixture Maintenance or Factory Setting.
Fixture Maintenance
Select Fixture Maintenance, press ENTER button to confirm, use UP and DOWN
button to select Interval or Remain Time.
Interval
Select Interval, press ENTER button to confirm, the interval time will show on the
display. Press MENU button to exit.
Remain Time
Select Remain Time, press ENTER button to confirm, the remaining time will show on
17
16

Swift1915Z Aura LED Moving Head Beam Wash Light User Manual Swift1915Z Aura LED Moving Head Beam Wash Light User Manual
the display, press ENTER button to confirm, use UP and DOWN button to select Exit or
Reset time, press MENU button to exit.
Factory Setting
Select Factory Setting, press ENTER button to confirm, the fixture will reset to factory
settings and exit menu mode.
3. Home Position Adjust
In the main functions, hold Enter button for at least 3 seconds into offset mode, use
DOWN and UP button up to chose Pan Offset, Tilt Offset or Zoom Offset, pressing ENTER
button and the display will blink. Use DOWN and UP button to adjust the home position of
the Pan, Tilt or Zoom, Once the position has been selected, press the ENTER button to
setup, to go back to the functions without any change press the MENU button again. Hold
and press the MENU button about one second or wait for one minute to exit the menu
mode.
ⅦADDRESS SETTING AND DMX CHANNEL OPERATION
If you use a universal DMX controller to control the units, you have to set DMX address
from 1 to 512 so that the units can receive DMX signal.
Press MENU button to enter menu mode, select DMX Functions, press ENTER button to
confirm, use UP and DOWN button to select DMX Address, press ENTER button to
confirm, the present address will blink on the display, use UP and DOWN button to adjust
the address from 0 to 512, press ENTER button to store. Press MENU button back to the
last menu or let the unit idle 7 seconds to exit menu mode.
Please refer to the following diagram to address your DMX512 channel for the first 4 units：
Channel mode
Unit 1 address
Unit 2 address
Unit 3 address
Unit 4 address
14 channels
1
15
29
43
14 DMX Channels mode
DMX CH
DMX Value
Function
CH1
000←→255
Pan 0~540/630degree
CH2
000←→255
Pan fine 1.8 degree, 16bit
CH3
000←→255
Tilt 0~280degree
CH4
000←→255
Tilt fine 1.8 degree, 16bit
CH5
000←→255
Pan/tilt motor running speed
CH6
000←→009
010←→014
015←→255
Reset
No function
Reset all
No function
CH7
000←→255
Dimmer, linear dimmer, 0-100%
CH8
000←→019
020←→024
025←→064
065←→069
070←→084
085←→089
Shutter
Closed
Open
Strobe
Open
Opening pulse
Open
19
18

Swift1915Z Aura LED Moving Head Beam Wash Light User Manual Swift1915Z Aura LED Moving Head Beam Wash Light User Manual
090←→104
105←→109
110←→124
125←→129
130←→144
145←→149
150←→164
165←→169
170←→184
185←→189
190←→204
205←→209
210←→224
225←→229
230←→244
245←→255
Closing pulse
Open
Random strobe
Open
Random opening pulse
Open
Random closing pulse
Open
Burst pulse
Open
Random burst pulse
Open
Sine wave
Open
Burst
Open
CH9
000←→255
Beam red, 0-100%
CH10
000←→255
Beam green, 0-100%
CH11
000←→255
Beam blue, 0-100%
CH12
000←→255
Beam white, 0-100%
CH13
000←→009
010←→014
015←→019
020←→024
025←→029
030←→034
Color wheel effect
Open
LEE 790-Moroccan pink
LEE 157-Pink
LEE 332-Special rose pink
LEE 328-Follies pink
LEE 345-Fuchsia pink
035←→039
040←→044
045←→049
050←→054
055←→059
060←→064
065←→069
070←→074
075←→079
080←→084
085←→089
090←→094
095←→099
100←→104
105←→109
110←→114
115←→119
120←→124
125←→129
130←→134
135←→139
140←→144
145←→149
150←→154
155←→159
160←→164
165←→169
LEE 194-Surprise pink
LEE 181-Congo blue
LEE 071-Tokyo blue
LEE 120-Deep blue
LEE 079-Just blue
LEE 132-Medium blue
LEE 200-Double CT blue
LEE 161-State blue
LEE 201-Full CT blue
LEE 202-Half CT blue
LEE 117-Steel blue
LEE 353-Lighter blue
LEE 118-Light blue
LEE 116-Medium blue green
LEE 124-Dark green
LEE 139-Primary green
LEE 089-Moss green
LEE 122-Fern green
LEE 738-JAS green
LEE 088-Lime green
LEE 100-Spring yellow
LEE 104-Deep amber
LEE 179-Chrome orange
LEE 105-Orange
LEE 021-Gold amber
LEE 778-Millennium gold
LEE 135-Deep gold amber
21

Swift1915Z Aura LED Moving Head Beam Wash Light User Manual Swift1915Z Aura LED Moving Head Beam Wash Light User Manual
170←→174
175←→179
180←→201
202←→207
208←→229
230←→234
235←→239
240←→244
245←→249
250←→255
LEE 164-Flame red
Open
Color rotation effect
Clockwise, fast to slow
Stop(this will stop wherever the color is at the time)
Counter-clockwise, slow to fast
Open
Random color
Fast
Medium
Slow
Open
CH14
000←→255
Zoom
Zoom, from 10-60
ⅧTROUBLE SHOOTING
Following are a few common problems that may occur during operation. Here are some
suggestions for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
3. Check the power on LED.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
of the unit or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may
cause damage or interference to DMX interface circuit.
C. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
ⅨMAINTENANCE AND CLEANING
The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater
accumulation of dirt on the unit’s optics.
�Clean with soft cloth using normal glass cleaning fluid.
�Always dry the parts carefully.
�Clean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
The following points have to be considered during the inspection:
1) All screws for installing the devices or parts of the device have to be tightly connected
and must not be corroded.
2) There must not be any deformations on the housing, color lenses, fixations and
installation spots (ceiling, suspension, trussing).
3) Mechanically moved parts must not show any traces of wearing and must not rotate with
unbalances.
4) The electric power supply cables must not show any damage, material fatigue or
sediments.
Further instructions depending on the installation spot and usage have to be adhered by a
23
22

Swift1915Z Aura LED Moving Head Beam Wash Light User Manual Swift1915Z Aura LED Moving Head Beam Wash Light User Manual
skilled installer and any safety problems have to be removed.
In order to make the lights in good condition and extend the life time, we suggest a regular
cleaning to the lights.
1) Clean the inside and outside lens each week to avoid the weakness of the lights due to
accumulation of dust.
2) Clean the fan each week.
3) A detailed electric check by approved electrical engineer each three month, make sure
that the circuit contacts are in good condition, prevent the poor contact of circuit from
overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never
use alcohol or solvents.
There are no serviceable parts inside the device. Please refer to the instructions under
“Installation instructions”.
Should you need any spare parts, please order genuine parts from your local dealer.
Please keep this manual as a reference.
Thanks again for your business. We truly appreciate it!
24