VanGaa Lighting VG-LB1083 User manual

VG-LB1083 LED Cyclorama Light User Manual VG-LB1083 LED Cyclorama Light User Manual
LED Cyclorama Light
VG-LB1083
CE RoHS
User Manual
Please read this user manual before using this product！
Keep it for further reference!
http://www.vangaa.com

VG-LB1083 LED Cyclorama Light User Manual VG-LB1083 LED Cyclorama Light User Manual
INDEX
ⅠPRODUCT MAIN FEATURES ............................................. 01
ⅡOVERVIEW AND DIMENSIONS ......................................... 01
ⅢSAFETY INFORMATION ................................................... 02
ⅣPOWER CONNECTION...................................................... 03
ⅤCONTROL PANNEL .......................................................... 05
ⅥDMX PROTOCOL.............................................................. 09
ⅦTECHNICAL SPECIFICATION ........................................... 10
Thank you for using our product! Please read this manual carefully and completely. For
technical reference in future, please keep this user manual well. This user manual contains
all installation and operation information of this LED Cyclorama Light, it’s very useful for
user to install and operate the light. Please strictly abide by the relevant instruction for the
installation and operation.
This light has very beautiful appearance. Based on the LED Film and Television Flat Light,
using high brightness led beads matrix arrangement of large area, through the whole
aluminum shell to realize heat dissipation naturally, we have designed this light. This light
has high brightness, good head dissipation, ultra-quiet and other features. It can satisfy the
requirement of indoor movie filming for the lighting layout. It is a good substitute of the
traditional ground panel light.
This light meets the following criteria:
GB7000.1-2007/IEC60598-1:2003
GB7000.217-2008/IEC60598-2-17:1984+A2:1990
ⅠPRODUCT MAIN FEATURES
·8CH DMX control channels, digital show control panel;
·DMX512, Sound active, auto-run and master/slave four kinds control mode;
·IP20 protect rating;
·With strobe stage effect;
·Long lifespan high brightness LEDs can reach to 50,000hours;
·High-efficiency, power-saving, low heat.
ⅡOVERVIEW AND DIMENSIONS
01

VG-LB1083 LED Cyclorama Light User Manual VG-LB1083 LED Cyclorama Light User Manual
All dimensions are in millimeters
ⅢSAFETY INFORMATION
※Important
Every person involved with the installation, operation and maintenance of this device has to
be qualified and follow the instructions of this manual. Manufacturer will not with
responsibility for those operations which are not according to this Instruction.
Verify that the voltage matches the rated voltage.
When the voltage is 110V , Do not connect more than 10 lightings in total to AC mains
power in one interconnected daisy chain
When the voltage is 220V , Do not connect more than 20 lightings in total to AC mains
power in one interconnected daisy chain
Before using the fixture, check that all power distribution equipment and cables are in
perfect condition and rated for the current requirements of all connected devices.
Always ground (earth) the fixture electrically.
Avoiding hit the Light when you are move or install the light.
The minimum distance between light-output and the illuminated surface must be
more than 0.5 meters. Keep all combustible materials (for example fabric, wood,
paper) at least 0.2 meters away from the fixture.
Do not expose the fixture to rain or moisture.
Avoid looking directly into the light source (especially those who suffer from epileptic
fits)
Maximum ambient temperature (Ta) is 40°C. Do not operate fixture at temperatures
higher than this.
The Maximum surface temperature is 50°C
When suspending the fixture above ground level, verify that the structure can hold at
least 10 times the weight of all installed devices.
Verify that all external covers and rigging hardware are securely fastened and use an
approved means of secondary attachment such as a safety cable.
ⅣPOWER CONNECTION
INSTALLING A NENUTRIK CONNECTOR ON A POWER CABLE
02
03

VG-LB1083 LED Cyclorama Light User Manual VG-LB1083 LED Cyclorama Light User Manual
Put bushing and chuck onto the cable.
Prepare cable as shown above. The power cable must is a three-conductor 2.5mm2
cable.
Insert the wire into the terminals and fasten the clamping device by a flat screw driver.
Push insert and chuck into housing (pay attention to the guiding keyway).
Fasten bushing.
The color-coding schemes and some possible pin identification schemes; if pins are not
clearly identified, or if you have any doubts about proper installation, consult a qualified
electrician.
RELAYING POWER TO OTHER DEVICES
The lightings can be linked in a chain by power cables which installed a blue and a light-gray
connectors on the two ends. The light-gray connector connects to the power out socket of
the first lighting, and the blue connector connects to the power in socket of the subsequent
lighting, and so on.
The power cable must is a three-conductor 2.5mm2cable.
When the voltage is 110V, Do not connect more than 10 lightings in total to AC mains power
in one interconnected daisy chain.
When the voltage is 220V, Do not connect more than 20 lightings in total to AC mains power
in one interconnected daisy chain.
PHYSICAL INSTALLATION
This lighting can be placed on a horizontal surface such as a stage or clamped to a truss or
similar rigging structure in any orientation using a rigging clamp.
When suspending the fixture above ground level, verify that the structure can hold at least
10 times the weight of all installed devices.
Verify that all external covers and rigging hardware are securely fastened and use an
approved means of secondary attachment such as a safety cable.
ⅤCONTROL PANNEL
BUTTON
Wire color
Conductor
Symbol
Brown
Live
L
Blue
Neutral
N
Yellow/green
ground
05
04
05

VG-LB1083 LED Cyclorama Light User Manual VG-LB1083 LED Cyclorama Light User Manual
SET/MENU
UP
DOWN
ENTER
Call the main menu, or escape the current menu, (i.e. return to the
upper menu and give up the selected item or parameter).
Browse the menu item forward or increase the parameter.
Browse the menu item backward or decrease the parameter.
Confirm the selected item or parameter, (i.e. enter into the next menu,
or escape the current menu and save the selected item or parameter).
INDICATOR
There are 4 dots at the bottom of the digital tube, from left to right as:
1. DMX signal LED indicator;
2. Memory writing indicator, (Press ENTER after amending the DATA, This Dot will be
light up, it means the Data is saving);
3. Power indicator;
4. Keyboard available indicator.
MAIN MENU
Press SET/MENU to turn the sub-menu
DISPLAY
FUNCTION
OPERATION
A.***
DMX mode(the "A" will flash
when control mode not
confirmed, the "." will not flash
under in slave mode, "***" will
flash when the DMX address is
not confirmed.
When show "A.***", press ENTER
button, the "***" will flash, then press
UP/DOWN to adjust the DMX address
value, then press ENTER keep the
setting.
AF.**
Gradual change automatic
running mode(**is the running
speed, from 1-99.)
Press SET button choose "AF.**", then
press ENTER button change into
gradual change automatic mode, then
press ENTER button, the "**" will flash,
then press UP/DOWN button to adjust
the speed which you need.
AL.**
Jump change automatic
running mode(**is the running
speed, from 1-99.)
Press SET button choose "AL.**", then
press ENTER button change into jump
change automatic mode, then press
ENTER button, the "**" will flash, then
press UP/DOWN button to adjust the
speed which you need.
MS.**
Sound active running
mode(**is the sensitivity value,
from 0-99-FL.)Note: only some
item has sound active function
Press SET button choose "MS.**", then
press ENTER button change into sound
active mode, then press ENTER button,
the "**" will flash, then press
UP/DOWN button to adjust the speed
which you need.
d1.**
Red signal cyclorama running
mode(**is the LEDx dimmer
value 0-99-FL
Press SET button choose "d1.**", then
press ENTER button change into red
signal cyclorama mode, then press
ENTER button, the "**" will flash, then
press UP/DOWN button to adjust the
brightness which you need.
06
07

VG-LB1083 LED Cyclorama Light User Manual VG-LB1083 LED Cyclorama Light User Manual
d2.**
Green signal cyclorama running
mode(**is the LEDx dimmer
value 0-99-FL
Press SET button choose "d2.**", then
press ENTER button change into green
signal cyclorama mode, then press
ENTER button, the "**" will flash, then
press UP/DOWN button to adjust the
brightness which you need.
d3.**
Blue signal cyclorama running
mode(**is the LEDx dimmer
value 0-99-FL
Press SET button choose "d3.**", then
press ENTER button change into blue
signal cyclorama mode, then press
ENTER button, the "**" will flash, then
press UP/DOWN button to adjust the
brightness which you need.
d4.**
White signal cyclorama running
mode(**is the LEDx dimmer
value 0-99-FL
Press SET button choose "d4.**", then
press ENTER button change into white
signal cyclorama mode, then press
ENTER button, the "**" will flash, then
press UP/DOWN button to adjust the
brightness which you need.
dF.**
Strobe running mode(**is the
strobe speed 0-99-FL
Press SET button choose "dF.**", then
press ENTER button change into strobe
running mode, then press ENTER
button, the "**" will flash, then press
UP/DOWN button to adjust the speed
which you need.
t.***
current temperature of the led lamp board(℃）
V.***
Version of software
H.on/H.oF
F
Lose DMX setting(on means
keep the last value, oFF means
delay reset
Press SET button to choose H.on/H.off,
then press ENTER, the on/off is flash,
press UP/DOWN to choose the
function which you need, then press
ENTER save.
Under DMX mode, the last "." flicker means the signal connection succeed.
Under other master mode, the last "." keep light;
When color temperature control error, the "...." keep light on.
ⅥDMX PROTOCOL
CH
Value
Function
CH1
000←→255
Dimmer, 0~100%
CH2
000←→255
Red dimmer, 0-100%
CH3
000←→255
Green dimmer, 0-100%
CH4
000←→255
Blue dimmer, 0-100%
CH5
000←→255
White dimmer, 0-100%
CH6
000←→004
005←→255
Strobe
No strobe
Strobe, from slow to fast
CH7
000←→009
010←→026
027←→043
044←→060
061←→077
078←→094
095←→111
112←→128
129←→145
146←→162
163←→179
180←→196
197←→213
214←→230
231←→247
248←→255
Color change
No Function
Preset Color 1
Preset Color 2
Preset Color 3
Preset Color 4
Preset Color 5
Preset Color 6
Preset Color 7
Preset Color 8
Preset Color 9
Preset Color 10
Preset Color 11
Preset Color 12
Preset Color 13
Preset Color 14
Preset Color 15
09
08

VG-LB1083 LED Cyclorama Light User Manual VG-LB1083 LED Cyclorama Light User Manual
CH8
000←→004
005←→100
101←→200
201←→255
Macro Function
No Function
Skip
Slip
Audio
CH9
000←→255
Speed, Skip or Slip speed
Note: under DMX512 mode, there is no light setting into master/sound active/strobe mode,
if not, the signal will mutual interference. Press SET when power on, the display shows Axxx
OR Sxxx means the light under DMX 512 mode, if shows other information means the light
is not under DMX 512 mode.
ⅦTECHNICAL SPECIFICATION
Light Sources
·L ED: 108pcs 3W high brightness LED Lamps, (R:27; G:27; B:27; W: 27)
·Lifespan: 50000h
·Color: RGBW mixing, colorful
Optics
·Beam angle: 120*60degree
·Dimmer: 0-100% linear dimmer
·Strobe: 1-25 times/second
·CRI: >85Ra
Light Output
·Optimal projection distance: 8-30m
Control
·Control mode: standard DMX-512; Master/slave; Demo
·DMX channel: 9CH
·Display of control panel: 4 buttons LCD display
·Special illustration: use aluminum profiles and aluminium plate to produce this light, it is
lightweight, rugged, beautiful, professional, project evenly light.
Power Supply
·Related voltage: AC100V-240V, 50/60Hz
·Related power: 360W
Construction
·Body dimension: D480*W270*H127mm
·Net weight: 8.5kg
·Shell color: black
·Shell material: aluminium alloy
Working Environment
·Working temperature: -25-40℃
·Cooling: Fan
·Protection rating: IP20
Innovation, Quality, Performance, Achieving Users’Value!
11
10