Vaporesso GEN NANO User manual

User Manual
VAPORESSO GEN NANO

1English
Thank you for choosing Vaporesso product. Please read this instruction
carefully before use to ensure a perfect experience.
If there is any additional requirement about this product, please consult
the local agent or contact us through our website: www.vaporesso.com
ENGLISH
EXPLODED VIEW
Drip Tip
Glass Tube
Air-inlet Ring
Power Button
0.91“ OLED Screen
“-” Button
Mode/Conrm
GTX Tank 22
“+” Button
USB Port

2English
SPECIFICATIONS
GEN NANO MOD
Dimensions 70.3*41.2*24.2mm
Output Power 5-80W
Charging Current DC 5V/2A, Micro USB
Display 0.91" OLED Screen
Battery Capacity Built-in 2000mAh
Tank Connection 510 Thread
GTX TANK 22
Dimensions 49.4 x 22.0 mm
Capacity 3.5ml / 2ml
Coils GTX 0.2Ω MESH Coil (45-60W)
GTX 0.6Ω MESH Coil (20-30W)

3English
PACKING LIST
USE INSTRUCTIONS
Regular Version:
1 x GEN NANO MOD
1 x GTX TANK 22 (3.5ml)
1 x GTX 0.2Ω MESH Coil(pre-installed)
1 x GTX 0.6Ω MESH Coil(in box)
3 x O-ring
1 x Glass Tube (2ml)
1 x GTX Coil Reminder Card
1 x USB Cable
1 x User Manual
1 x Warranty Card
TPD Version:
1 x GEN NANO MOD
1 x GTX TANK 22 (2ml)
1 x GTX 0.2Ω MESH Coil(pre-installed)
1 x GTX 0.6Ω MESH Coil(in box)
3 x O-ring
1 x Glass Tube (2ml)
1 x GTX Coil Reminder Card
1 x USB Cable
1 x User Manual
1 x Warranty Card
1. Install the Tank
Install the tank to the battery by screwing the 510 thread. Make
sure they are rmly connected.

4English
2. Replace the Coil
- Unscrew the thread
base from the tank;
- Pull out the used coil
in the tank;
- Install a new coil to
the tank;
- Reattach the thread
base into place.
3. Fill the E-liquid
- Unscrew the top cap
from the tank;
- Fill the e-liquid along
the glass tube;
- Reattach the top cap
back into place;
- Please wait 5 minutes
for the e-liquid to soak
into the coil completely.
PULL
OPEN
OPEN
PUSH
CLOSE
CLOSE

5English
4. Adjust the Airow
To adjust the airow volume, please rotate the air-inlet ring on the
bottom of the tank.
5. Adjust the Power
GEN NANO is based on the GTX coil platform, and the power range
of the adopted coil will be displayed on the screen.
6. Start Vaping
Press and hold the power button to start vaping. For your safety, please
do not vape for more than 10s at a time.
7. About Charging
After the USB cable is connected to the battery, the screen indicator
and remaining charging time will be displayed on the screen.
GTX Coil GTX 0.2Ω MESH GTX 0.6Ω MESH
Suggested Power 45-60W 20-30W

6English
8. Lock/Unlock the Buons
Press the power button 3 times continuously to lock or unlock the “+”
button, “-” button and mode button. The power button still works.
9. Choose a Mode
Press the mode button 3 times continuously or long press the mode
button to start mode setting.
*PUL: PULSE MODE (DEFAULT)
After the atomizer is installed, the device will enter the PULSE MODE
automatically.
PULSE MODE: It’s a mode to improve vaping experience through
constant voltage output, delivering optimal avor production, nicotine
satisfaction, and perfect temperature cloud continuously.

7English
*ECO: POWER ECO MODE
When thebattery levelis below 40% and unable to support thepreset
power, thedevice will automatically provide an option to enter the
POWER ECO mode for increasing endurance.
*STC: SMART TEMPERATURE CONTROL MODE
When the temperature heating wire (SS/Ti/Ni) isdetected, thedevice
will provide an option to enter the STC (Smart TC) mode automatically.
*DIY: DIY MODE
You can choose traditional VW (H, N, S), VV, VT, CCW, BP (bypass) and
SP (super player) modes in this section. When the coil resistance is
extremely low, thedevice will provide an option to enter theSP (Super
Player) mode automatically.

8English
*SET: SYSTEM SETTING
System setting includes puff counter, brightness, ip screen, smart
VW on/off, Auto Eco on/off, default and version settings, the operating
interface can be customized by yourself.
Smart VW: when this function is turned on and an atomizer is installed,
the system will recommend the best power for you.
Auto Eco: Choose POWER ECO mode for saving power and increasing
endurance.
*VWS/VWN /VWH (Variable Wattage Mode)
VWH: high start-up speed
VWN: normal start-up speed
VWS: soft start-up speed
10. DIY MODE

9English
*VT-SS/VT-NI/VT-TI/VT-MI
(Variable Temperature Control Mode)
The SS, NI and TI modes are only available for the Stainless Steel
SUS316L, Nickel 200 and Titanium materials respectively. Choose the MI
mode to make a customized setting when other heating wire materials
are installed.
*VV (Variable Voltage Mode)
Customize the voltage according to your needs.
*CCW (Customized Curve of Wattage Mode)
Press the “+” and “-” buttons to customize your curve of wattage
output; press the mode button moving to the next bar; press the power
button to save and exit when the setting is done.

10 English
*BP (Bypass Mode)
A direct voltage output mode depends on the battery level; the effective
coil resistance range is from 0.15Ω to 5Ω.
*SP (Super Player Mode)
In DIY mode, when the coil resistance of the loaded coil is between
0.03-0.05Ω, the system will prompt to enter the super player mode,
which is suitable for the RDA/RBA coil with ultra-low resistance.
PROTECTIONS
No. Protections Situations
USB Input Protection The USB input voltage is higher than the rated
voltage.
1

11English
Low Battery Protection The battery level drops too low.
No Load Protection The device detects no atomizer on the battery.
Short-circuit
Protection The device detects a short circuit.
Overtime Protection Constantly vape for more than 10 seconds.
Overheat Protection The device detects an overheated PCBA.
Dry Protection In Smart TC mode, the device detects
insufcient e-liquid remaining.
1
3
5
7
2
2
4
6
3
4
5
6
7

12 English
1. Please turn off the device when it is not in use.
2. Do not leave the charging device unattended.
3. Do not drop, throw or abuse your device, which may cause
damage.
4. Please use a standard USB output charger with proper charging
current and voltage range.
5. Keep away from the water or any ammable gas, liquid .
6. Do not expose the device to direct sunlight, dust, moisture or
mechanical shock.
7. Do not expose the device to extreme temperature. (Recommended
temperature range:
-10~60℃/14~140℉while using and -10~45℃/14~113℉ while storing).
8. EEE Recycling: the product should not be treated as household
waste, instead, it should be
handed over to the applicable collection point for the recycling of
electrical and electronic
equipment.
CAUTIONS

13English
9. Battery Recycling: the product battery should not be treated as
household waste, instead, it
should be handed over to the applicable used battery collection point
for recycling.
10. Only have your device repaired by Vaporesso. Do not attempt to
repair it by yourself as damage or personal injury may occur.
This rellable electronic cigaree is intended for use with compatible
e-liquid, which may contain nicotine. Nicotine is an addictive substance
and it is not suitable or recommended to use in following cases:
1. This device is not suitable for:
- Persons under the legal smoking age.
- Persons experiencing heart disease, stomach or duodenal ulcers, liver
or kidney problems, long-term throat disease or difcult breathing due
to bronchitis, emphysema or asthma.
- Persons with an overactive thyroid gland or experiencing
phaeochromocytoma (a tumour of the adrenal gland that can affect
WARNINGS

14 English
blood pressure).
- Persons taking certain medications like Theophylline, Ropinirole or
Clozapine and etc..
2. This device is not recommended for:
- Non-smokers
- Pregnant or breastfeeding women
3. You may experience the following results if you use nicotine
containing e-liquid with this product. If it happens, please consult a
healthcare professional and show them this leaet if possible:
- Feeling faint - Nausea - Dizziness - Headache - Coughing
- Irritation of the mouth or throat - Stomach discomfort
- Hiccups - Nasal congestion - Vomition
- Chest palpitations/pain or an irregular heart rate
This device should not be used by persons
under the legal smoking age.

1Français
FRANÇAIS
Nous vous remercions d’avoir choisi un produit Vaporesso. Veuillez lire
attentivement les présentes instructions avant de l’utiliser an de garantir une
expérience optimale. S’il existe des exigences supplémentaires relatives à ce
produit, veuillez contacter votre agent local ou prendre contact avec nous sur
notre site Web: www.vaporesso.com
EXPLODED VIEW
Drip Tip
Tube de verre
Anneau d’entrée d’air
Bouton d’alimentation
Écran OLED
Bouton « - »
Mode/Conrmer
GTX Tank 22
Bouton « + »
Port USB

2Français
CARACTÉRISTIQUES
GEN NANO MOD
Dimensions 70,3 x 41,2 x 24,2 mm
Puissance de sortie 5-80 W
Courant de charge 5 VCC/2A, micro USB
Afchage Écran OLED de 0,91 pouce
Capacité de la batterie Batterie intégrée de 2 000 mAh
Raccord du réservoir Filetage 510
GTX TANK 22
Dimensions 49,4 x 22,0 mm
Capacité 3,5ml/2ml
Résistances Résistance GTX 0,2 Ω MESH (45-60 W)
Résistance GTX 0,6 Ω MESH (20-30 W)

3Français
LISTE DES ARTICLES
CONSIGNES D’UTILISATION
Version normale:
1 x GEN NANO MOD
1 x GTX TANK 22 (3.5ml)
1 x Résistance GTX 0,2 Ω MESH
1 x Résistance GTX 0,6 Ω MESH
3 x O-ring
1 x tube de verre (2 ml)
1 x carte de rappel de résistance GTX
1 câble USB
1 manuel de l’utilisateur
1 bon de garantie
Version TPD:
1 x GEN NANO MOD
1 x GTX TANK 22 (2ml)
1 x Résistance GTX 0,2 Ω MESH
1 x Résistance GTX 0,6 Ω MESH
3 x O-ring
1 x tube de verre (2 ml)
1 x carte de rappel de résistance GTX
1 câble USB
1 manuel de l’utilisateur
1 bon de garantie
1. Installation du réservoir
Installez le réservoir sur la batterie en les vissant ensemble grâce
au letage 510. Vériez qu’ils sont fermement connectés.

4Français
2. Remplacement de la résistance
- Unscrew the thread
base from the tank;
- Pull out the used coil
in the tank;
- Install a new coil to
the tank;
- Reattach the thread
base into place.
3. Recharge de l’E.-liquide
- Unscrew the top cap
from the tank;
- Fill the e-liquid along
the glass tube;
- Reattach the top cap
back into place;
- Please wait 5 minutes
for the e-liquid to soak
into the coil completely.
PULL
OPEN
OPEN
PUSH
CLOSE
CLOSE