Vaporesso Swag II User manual

User Manual
VAPORESSO SWAG II

1English
Thank you for choosing Vaporesso product. Please read this instruction carefully before use to
ensure a perfect experience. If there is any additional requirement about this product, please
consult the local agent or contact us through our website: www.vaporesso.com
EXPLODED VIEW
ENGLISH
Drip Tip
Tank Base
Air-inlet Ring
Top Cap
Battery Cover
"+" Button
"-" Button
Power Button
OLED Screen
Mode Button

2English
PACKING LIST
SPECIFICATIONS
SWAG II MOD
Dimensions: 50 x 25 x 75mm
Resistance: 0.03-5.0Ω
Output Wattage: 5-80W
Charging Current: DC 5V/2A, Micro USB
Display: 0.91" OLED Screen
Chipset: AXON CHIP
Battery: 1 x 18650 (not included)
Battery Compatibility: 510
Tank Compatibility: Max 25mm
Regular Version:
1 x SWAG II MOD
1 x NRG PE TANK(3.5ml)
1 x GT4 MESHED Coil
1 x GT CCELL Coil
TPD Version:
1 x SWAG II MOD
1 x NRG SE MINI TANK(2ml)
1 x GT4 MESHED Coil
1 x GT CCELL Coil
4 x O-ring
1 x USB Cable
1 x User Manual
1 x Warranty Card
3 x O-ring
1 x USB Cable
1 x User Manual
1 x Warranty Card
NRG PE TANK
Dimensions: Φ25 x 50mm
Capacity: 3.5ml
Coil: 0.15Ω GT4 MESHED Coil (50-75W)
0.5Ω GT CCELL Coil (25-35W)
NRG SE MINI TANK
Dimensions: Φ22 x 46mm
Capacity: 2ml
Coil: 0.15Ω GT4 MESHED Coil (50-75W)
0.5Ω GT CCELL Coil (25-35W)

3English
1. Replace the Coil
- Remove the base of the tank.
- Twist off the used coil on the base.
- Install a new coil to the base.
- Reattach the base to the tank.
2. Install the Tank
Connect the tank to the MOD by screwing the 510 connector. Make sure they are firmly
connected.
3. Fill the E-liquid
1) Regular Version
- Twist the top cap and ll the e-liquid through the slot.
- Lock the top cap back into place.
- Please wait for 5 minutes for the e-liquid to soak into
the coil.
USE INSTRUCTION
OPEN OPEN CLOSECLOSE
OPEN
CLOSE
1 2 3 4 5 76
1 2 3

4English
2) Child-protection Version
- Pull out the drip tip and twist the top cap.
- Fill the e-liquid through the slot.
- Lock the top cap and drip tip back into place.
- Please wait for 5 minutes for the e-liquid to soak into the coil.
4. Adjust the Airow
Twist the air-inlet ring on the bottom of the tank to adjust the airow volume.
1 2 3 4 5 6
5. Start the Device
1) Power on/off: Press the power button 5 times in 2s.
OPEN
CLOSE

5English
2) Lock/unlock the buttons: Press the power button 3 times
continuously to lock or unlock the "+" Button, "-" Button and Mode
Button.
3) Mode Button: Press the Mode Button 3 times continuously to start
modes setting.
4) The NEW LOAD and OLD LOAD will show on the screen after a tank
is installed.
a. In the SMART VW ON mode, press “+” (NEW LOAD) to enter the
device recommended wattage; press “-” (OLD LOAD) to enter the
wattage that you have already set.
b. In the SMART VW OFF mode, to produce the best temperature
control effect, please press “+” (NEW LOAD) when installing a new
tank, and press “-” (OLD LOAD) when installing a used tank.
5) Vaping: Press the power button to start to vape. For your safety, please do not vape for
more than 10 seconds at a time.

6English
*PUL: PULSE Mode (DEFAULT)
When the tank is installed, the device will enter the PULSE MODE
automatically to boost avor with large cloud continuously.
*ECO: POWER ECO Mode
When the battery power is less than 40%, the device will provide an
option to enter the POWER ECO mode automatically.
*STC: SMART TEMPERATURE CONTROL Mode
When the temperature heating wire (SS/Ti/Ni) is detected, the device
will provide an option to enter the STC(Smart TC) mode automatically.
*DIY: DIY Mode
You can choose traditional VW(H, N, S), VV, VT, CCW, BP (bypass) and
SP( super player) modes in this section. When the coil resistance is
extremely low, the device will provide an option to enter the SP (Super
Player) mode automatically.
6. Choose a Mode

7English
7. Options in DIY MODE
*VWS/VWN /VWH (Variable Wattage Mode)
VWH: high start-up speed
VWN: normal start-up speed
VWS: soft start-up speed
*VT-SS/VT-NI/VT-TI/VT-MI (Variable Temperature Control Mode)
The SS, NI and TI modes are only available for the Stainless Steel
SUS316L, Nickel200 and Titanium materials respectively. Choose the MI
mode to make a customized setting when installing other heating wire
materials.
*VV(Variable Voltage Mode)
Customize the voltage value according to your requirements.
*SET: SYSTEM SETTING
Including puff counter, brightness, flip screen, smart VW, auto eco
on/off, default and version settings, the operating interface can be
customized by yourself.

8English
*CCW (Customized Curve of Wattage Mode)
Press “+” and “-” buttons to customize your own curve of wattage
output; move to the next bar with a quick press to the Power Button;
press the Mode Button to save and exit when the setting is done.
*BP (Bypass Mode)
A direct output voltage mode depends on the battery level; the
supported coil resistance range is from 0.15Ω to 5Ω.
*SP (Super Player Mode)
The device supports broader resistance range from 0.03Ω to 5.0Ω,
which is adaptive to the mainstream tanks such as RDA and RBA.