Vax C85-Z1-Be Installation instructions

DYNAMIC POWERFUL
PERFORMANCE
C85-Z1-Be
LET’S GET STARTED.
DynamoPower

Let’s talk safety
Basic
safety
precautions
Don’ts
Do’s
This vacuum cleaner is intended for household use only
and NOT for commercial or industrial use.
• Only use the vacuum cleaner indoors on dry surfaces
and keep the area you’re cleaning well lit.
• Keep ngers, hair and loose clothing from moving parts
and openings whilst using the vacuum cleaner.
• This vacuum cleaner can be used by children aged from
8 years and above and persons with reduced physical,
• Don’t use this vacuum cleaner if it has been dropped, damaged
or left outdoors.
• Don’t run over the power cord or use vacuum cleaner if the
power cord or plug is damaged. Please contact our Customer
Service Line on: 0330 026 8455 (Mon-Fri 8:30am to 6:30pm,
Sat 9:00am to 5:00pm).
• Don’t handle the plug or use the vacuum cleaner with wet hands.
• Don’t pull or carry this vacuum cleaner by the power cord.
• Don’t use the power cord as a handle, pull the power cord around
corners, sharp edges or close a door over the power cord.
• Don’t unplug vacuum cleaner by pulling on the power cord.
• Turn o all controls on the vacuum cleaner before
disconnecting or connecting the power cord.
• Always make sure both the pre-motor/post-motor lters are
in place before use.
• Always switch o the vacuum cleaner before disconnecting
or connecting the hose and accessories.
• Keep all openings clear and free from debris as this may aect
the airow/suction.
• Always replace the fuse in the plug with a British 13amp fuse.
• Always protect the power cable from heated surfaces and
open ames.

sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the vacuum
cleaner in a safe way and understand the hazards involved. Children shall
not play with the vacuum cleaner. Cleaning and user maintenance shall not
be made by children without supervision.
• Only Vax recommended tools and accessories should be used with this
vacuum cleaner.
• Don’t vacuum up any ammable or combustible materials (lighter uid, petrol,
kerosene etc.) or use the vacuum cleaner in an area with explosive vapours
or liquid.
• Don’t vacuum up hot coals, cigarette butts, matches or smoking hot burning
items or use in an area where there may be harmful uids (chlorine, bleach,
and ammonia drain cleaner).
• Don’t attempt to remove blockages with sharp objects as this may cause
damage to your vacuum cleaner.
• Don’t vacuum up hard or sharp objects such as glass, nails, screws or coins etc.
• Don’t use the vacuum cleaner with incorrect voltage as this may result in
damage or injury to the user. The correct voltage is listed on the ratings label.
• Take extra care when positioning and using the vacuum cleaner on the stairs.
• Use only CE approved 13amp extension cords, non-approved extension cords
may overheat. Care should be taken to arrange the extension cord as it can
be a trip hazard.
• Store your vacuum cleaner in a cool, dry area. If lters have been cleaned
as per user guide instructions ensure they are thoroughly dry before
storing away.
PLEASE KEEP INSTRUCTIONS FOR FURTHER USE.

Thank you for buying this Dynamo Power.
Taking care of your carpets and hard oors
The Dynamo Power is designed to make vacuuming carpets and hard oors regularly, as eective
and ecient as possible and this user guide will help you get the most out of your machine.
Maintaining your carpets and hard oors will ensure they keep their appearance for longer.
You’ve chosen carpets and hard oors for your home for a reason and Vax will help you take
good care of them.
Taking care of your Dynamo Power
Also inside this guide are instructions on maintaining your new machine, so that it’s always ready
when you are to tackle your carpets and hard oors.
Let us know what you think @VaxUK
Taking care of you
We’re here if you need us. Instead of taking me back
to the shop, simply visit:
vax.co.uk/support or call:
(UK) 0330 026 8455 (ROI) 1-800 928 308
Monday-Friday 8:30am to 6:30pm, Saturday 9:00am to 5:00pm
Calls are charged at the UK local rate. Please make a note of the serial number and model number
of the product before calling.
Alternatively, you can write to us at:
Vax Ltd., Plot 302, Stonebridge Cross Business Park, Hampton Lovett, Droitwich,
Worcestershire, WR9 0LW, UK
This user guide can be found online at: vax.co.uk/support

Contents
Let’s talk safety
Getting to know your machine
Getting started
Using your machine
Taking care of your machine
Let’s talk technical
Accessories
What to do if it goes wrong
Getting in touch
Included with
your machine
Accessory Hose
Combination Floorhead
Telescopic
Extension Tube
Initial Setup for normal operation
1. Use the base accessories.
a. Shortest hose.
b. Extension tube set to shortest practicable length.
2. Clean lters installed.
3. Dust receptacle empty.
4. All Bleeds must be closed.
5. Floorheads/tools set to Carpet Mode for carpet cleaning.
6. Mechanical Agitation turned ON for carpet cleaning.
7. Floorheads/tools set to Hard Floor Mode for hard oor cleaning.
8. Mechanical Agitation turned OFF for hard oor cleaning.
3-in-1 Tool
Dynamo Power
(Included with all models)

Getting to know your machine
Name Dynamo Power
Voltage See rating label on machine for details
Wattage See rating label on machine for details
Cord length 6m
Weight 4.5kg
Technical Specication
Subject to technical change without notice.
TurboTool (Type 6)
1-1-134419-00
Tool connector (Type 1)
1-1-133838-00
Combination oorhead tool (Type 5)
1-1-134341-00
Accessories & Consumables
*To purchase consumables and accessories, please visit vax.co.uk
Getting started
Carry handle
Separator
Dirt container release button
Power On/O button
Hose entry point
Dirt bin lid release clip
Cord rewind button
Post-motor lter
cover release clip
Post-motor lter cover
Dirt container

PLEASE READ ‘LET’S TALK SAFETY’ AT THE BEGINNING BEFORE USE
*To purchase consumables and accessories, please visit vax.co.uk
Getting started
Before you begin cleaning
• Always switch o and unplug the vacuum cleaner before connecting or disconnecting the hose/attachments,
or removing and emptying the dirt container.
• The vacuum cleaner is equipped with a thermal cut-out. If for any reason the vacuum cleaner does overheat the
thermostat will automatically turn the vacuum cleaner o. If this happens, switch the vacuum cleaner o and unplug
from electrical socket. Remove and empty the dirt container also check the vacuum cleaner for blockages. Allow the
vacuum cleaner to cool for approximately 1 hour (if you have cleaned the lters please wait 24 hours for the lters
to fully dry before putting back into the vacuum machine).
• Clean the pre-motor lter every time the dirt container is emptied and replace the post-motor lter every 12 months.
• If the vacuum cleaner is blocked, switch o and unplug before removing the blockage.
Assembling your vacuum cleaner
Press both buttons at the end
of the hose and push hose
into the hose entry point.
Insert the hose grip into the
telescopic extension tube.
Fully unwind the power
cord. A yellow mark on
the cord indicates the
recommended cord length.
Do not exceed the cord
beyond the yellow mark.
Plug into mains and press
the On/O button to
switch the machine on.
Press the button on the
telescopic extension
tube and adjust to
required length.
Insert the other end of
the telescopic extension
tube into the oorhead.
When unwinding the
power cord always pull
out to the yellow marker
but no further.
CAUTION

Using your machine
For use on carpets, click
rocker switch forward.
For use on hard oors
click rocker switch back.
Slide vent cover on hose
grip open to reduce
suction if required.
Raise brushes for carpets. Lower brushes
for hard oors.
How to use
Using your machine
CAUTION: The base of the vacuum cleaner should always be positioned at on the oor when starting and in use.
The dirt container should be locked into place before lifting the vacuum cleaner by the carry handle.

Press the cord rewind
button to retract the cord
into the vacuum cleaner.
Place the oorhead into the parking
slot on the back of the vacuum
cleaner for storage and carrying.
Using your machine
Using your machine
Choose an accessory. Push accessory onto
the telescopic extension
tube or hose.
Using accessories
Storage
CAUTION: Make sure to hold the cord with your other hand to prevent injury when rewinding.

Taking care of your machine
Cleaning the pre-motor lter and sponge
Remove dirt container
by pushing down the dirt
container release button and
lifting the dirt container.
Lift the dirt bin lid release
clip. In a hinge like manner
lift dirt bin lid.
Tap the pre-motor lter and
sponge against a bin to remove
any dirt/debris.
TAP
MAX
40˚C
!
MAX
40˚C
24hr
Lift the pre-motor lter and
sponge to remove from the
dirt container.
Hold dirt container over a bin.
Pull the dirt release clip at the
bottom of the container, the
dirt release door will open
allowing dirt/debris to fall out.
Emptying and cleaning the dirt container
Taking care of your machine
IMPORTANT: Always switch o and unplug the vacuum cleaner from the electrical socket before assembling,
opening or emptying the dirt container, or before connecting/disconnecting the attachments.
Pre-motor lter needs to be cleaned every time you empty the dirt container. Do not use your vacuum cleaner
without all of the lters in place.
The motor is equipped with a thermal cut-out. If for any reason the unit should overheat, the thermostat will
automatically turn the unit o.
Separate the sponge and lter
and rinse under water
(Max 40°C).
Leave to dry for 24 hours or until fully
dry before placing back in the machine.
TIP
Don’t over ll the
dirt container to
avoid blocking the
air ow through the
vacuum cleaner.
MAX
40˚C
!
MAX
40˚C
24hr
24hr

Lift the dirt bin lid release
clip. In a hinge like
manner lift dirt bin lid.
Cleaning the separator
Lift the pre-motor lter and
sponge to remove from the
dirt container.
Using central grips lift
to remove separator
from dirt container.
Tap the separator against
a bin to remove any dirt
or debris.
Taking care of your machine
Twist grips clockwise
and remove cap
from separator.
CAUTION: Incorrect tting of the separator cap will reduce suction.
Replace the separator cap,
twist clockwise to lock.
Replace separator into dirt container, make sure
the rectangular hole in the dirt container lines
up with the rectangular hole on the separator.
T
AP
IMPORTANT: Incorrect tting of the separator will reduce suction.
Retting the separator
TIP
For any stubborn dirt/
debris remaining in
the separator, use a
soft brush to remove.

Let’s talk technical
Remove the hose from the vacuum cleaner and telescopic
extension tube. Insert a broom handle or similar blunt
instrument into the hose to remove blockage.
Removing blockages from the hose
Accessories
Post-motor lter maintenance
Push the post-motor lter cover
release clip to the right to remove
the post motor lter cover.
Pull the post motor lter
to the left and remove the
post motor lter.
IMPORTANT: The post-motor lter is designed to oer long life with no maintenance. The lter should be
checked periodically and when heavily discoloured it should be replaced. Please do not wash, scrub or brush
the lter as this will damage the lter.
Check the post motor lter for discolouration.
Do not wash the post motor lter.
TIP
To test for a blockage in
the hose, drop a small
ball of paper into the
hose. The paper will
drop through if the
hose is clear.

Accessories
Pro Cleaning Kit (Type 2)
1-1-133326-00
All our best tools all in one kit that makes cleaning
your home quicker, easier and with even better
results. We’ve taken care of cleaning all of the hard
to reach areas such as on top of cupboards and in
between blinds to the dust that collates behind and
within the radiator.
Don’t forget your accessories!
Order at: www.vax.co.uk/spares-and-solutions
TurboTool (Type 6)
1-1-134419-00
Use the TurboTool for vacuuming your stairs,
upholstery and car interiors. It’s great for picking
up stubborn pet hair.
Fur ‘n’ Flu Tool
1-1-131392-00
Specically designed to remove extra stubborn
pet hair from upholstery, furniture and carpets.

• Check the ‘This pack contains’ panel on the box to make sure the part
is included with your vacuum cleaner.
• The dirt container may not be correctly tted, remove the dirt container from
the vacuum cleaner and check it’s assembled correctly, ret ensuring it’s locked
into place.
• The separator is blocked. Go to ‘Taking care of your machine’.
• The separator is incorrectly tted. Go to ‘Taking care of your machine’.
• The lter may be clogged, clean the lter. Go to ‘Taking care of your machine’.
• The dirt container may be blocked, empty the dirt container. Go to ‘Taking care
of your machine’.
• There may be a blockage in the hose/tube. Disconnect from the vacuum cleaner
and carefully remove any blockages. Go to ‘Let’s talk technical’.
• The lters may be clogged, clean the lter. Go to ‘Taking care of your machine’.
• The plug may not be fully pushed into the electrical socket.
• Check the fuse in the plug if this needs replacing, always replace with
a British 13amp fuse.
• The motor thermostat may have tripped. If this has happened, unplug the
vacuum cleaner. Remove and empty the dirt container and check the hose
for blockages. Clean the lters and allow the vacuum cleaner to cool for
approximately 1 hour (if you have washed the lters you will need to wait
24 hours for the lters to fully dry before putting them back into the
vacuum cleaner).
SolutionProblem
IMPORTANT: To reduce the risk of personal injury, unplug the vacuum before performing maintenance/
troubleshooting checks.
What to do if it goes wrong
There is an
accessory missing
Why won’t the vacuum
cleaner pick up?
Why does my vacuum
cleaner have no power?
Why is dust escaping
from the vacuum?

†
Getting in touch
†Registration required. Terms and conditions apply, see vax.co.uk for details.
* Calls are charged at the UK local rate. Please make a note of the serial number and model number of the product before calling.

GET IN TOUCH
0330 026 8455 VaxVacuums[email protected].uk vax.co.uk @VaxUK
EEC Statement of Compliance: Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
C85-Z1-Be manufactured in compliance with the following Directives: Safety: 2006/95/EC Low Voltage Directive.
EMC: 2004/108/EC Electromagnetic Compatibility Directive.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your Local Authority or retailer for recycling advice.
© 2015 All rights reserved. VAX®, VAX Lozenge, are trade marks or registered trade marks of Techtronic Floor Care
Technology Ltd.