Vax V-051 Product information sheet

easy guide
Please read carefully before using your
cleaner. Always fully extend mains
cable before use.
V-051/V-052
V-053/V-054
Cylinder range

Parts checklist
Parts Accessories Optional accessories
1) Carry handle 9) Dusting brush 13) TurboToolTM (V-052 only)
2) On/off button 10) Upholstery tool 14) Turbobrush (V-053 only)
3) Cord rewind button 11) Crevice tool
4) Hose connection socket 12) Combination floor head
5) Dust container
6) Top cover release buttons
7) Carry handle release button
8) Telescopic extension tubes
4
5
11 912
13
14
10
3
1
27
6
8

Assembling the cleaner
21
fig. 1 To attach the flexible hose to the vacuum cleaner, push the connecting end of the flexible hose into the hose
connection socket on the vacuum cleaner by pressing the two buttons on either side of the hose connection.
fig. 2 The telescopic extension tubes can be lengthened or shortened by pushing the button forward and sliding the
tubes apart or together as required.

Assembling the easy-reach tool system
Your Vax cylinder is equipped with easily-accessible tool storage. To assemble this, please follow these instructions.
fig. 3 The tool storage system fixing bracket is already in place on the extension tube.
Insert the holding tubes as shown until the tubes click into place.
fig. 4 Place the dusting brush (A), upholstery tool (B) and crevice tool (C) on the tubes as shown.
34A
C
B

56
Adjusting the combination head for carpets & hard floors
Your Vax cylinder comes equipped with a combination floor head that can be used on carpets and hard floors.
Flick the rocker switch to the appropriate position as detailed below.
fig. 5 Hard floor position (tiles, parquet floors, etc) – the brushes must be in the lower position. Press on the
rocker switch to lower them.
fig. 6 Carpet or rug position – the brushes should be raised. Press the rocker switch to raise them.

How to use your Vax cylinder
Note: Fully extend the mains cable and plug it into a standard domestic outlet.
fig. 7 Press the on/off button to start the vacuum cleaner. To stop it, press the on/off button again.
fig. 8 Press the cable rewind button to recoil the power lead.
fig. 9 The hose grip has a bleed valve that allows control of suction power. To reduce suction (for example, for
use on soft furnishings), open the bleed valve by sliding the plastic cover away from you. To increase
suction, close the bleed valve by sliding the plastic cover towards you.
8
7
9

Carry handle release how to store
fig. 10 The carry handle can be ‘locked’securely by pushing the handle down until it lies flush with the
machine body (fig.10); you will hear the handle click into place. To release the handle, slide the release
catch (fig.10a) towards the hose end of the machine.
fig. 11 For storage, you can position the vacuum cleaner as shown. Note: the carry handle must be ‘locked’
(see fig.10) and the cleaner must be switched off.
fig. 12 The hook on the telescopic tubes fits in to the retaining block on the underside of the vacuum cleaner.
10 11 12
10a

How to empty the dust container
fig. 13 Turn off the cleaner and unplug. Press the two top cover release buttons and raise the top cover to
access the dust container.
fig. 14&15 Remove the dust container by lifting it out as shown.
fig. 16 Press the release button over a rubbish bin so that the dirt can be emptied (fig.16). After emptying,
close the bottom flap (fig.16a) and re-assemble the cleaner.
Note: See figures 17-20 for filter cleaning methods.
13 14 15 16
16a

17
To clean or change the filters
Main filter - This filter should be cleaned frequently and washed occasionally.
fig. 17 The cyclone jug filter is located in the top of the dust container. Remove the filter and tap against the side of a
rubbish bin to remove excess dust. The filter can be washed but must be dried thoroughly before re-using.
Vax recommend this filter is replaced annually.
Motor protection filter
fig. 18 The pre-motor filter is located next to the dust container and protects the motor from dust. To access this filter,
open the lid, remove the filter and clean by brushing lightly with the dusting brush.
Exhaust filter
fig. 19 The exhaust filter is housed in the rear of the cleaner. Remove the exhaust filter cover by pressing the tab on
the top of the filter cover down, then pull the cover towards you.
fig. 20 Remove the dirty filter assembly from the cleaner and dispose of the filter. Note: this filter cannot be washed.
Vax recommend this filter is replaced every 6-12 months, depending on usage.
Attention: Do not use the vacuum cleaner without all of its filters in place.
18 19 20

Troubleshooting
Optional accessories
Problem Possible cause Possible solution
Cleaner won’t run •Power cord not firmly pushed into mains socket. •Plug cord in firmly to power outlet.
•Blown fuse or tripped circuit breaker. •Check fuse/breaker. Replace fuse or reset breaker.
Cleaner won’t pick up/loss of suction •Dust container not installed properly. •Re-install dust container.
•Dust container full. •See ‘How to empty the dust container’(fig.13-16a).
•Nozzle/dirt passage clogged. •Remove obstruction.
•Filters are clogged. •Clean or replace filters (fig.17-20).
Dust escaping from cleaner •Dust container not installed properly. •Re-install dust container.
•Dust container is full. •See ‘How to empty the dust container’(fig.13-16a).
TurboToolTM (model V-052 only)
How to use
•The TurboToolTM fits on the end of the telescopic tubes and/or hose grip.
•Perfect for cleaning stairs and upholstery.
•The TurboToolTM should be pulled backwards for optimum cleaning.
Clearing blockages
•Rotate the locking ring 180˚, then turn the TurboToolTM over.
•Pivot the lower housing open, then remove any obstructions.
•To re-assemble, ensure the tabs are engaged, pivot the lower housing closed
then re-position the locking ring.
Turbobrush (model V-053 only)
Please note
•The Turbobrush is especially suited for looking after rugs and carpets. The
Turbobrush is not suitable for hand-knotted or extremely deep pile rugs and
carpets. There is a danger that threads will be pulled.
Clearing blockages
•In case of a defective drivebelt, call the Vax Careline 0870 6061248.
•Disconnect the vacuum cleaner from the power supply before cleaning the
brushes.
•Cut the threads and hairs from around the brushbar.
•The debris can be vacuumed up afterwards.