Vaxcel T0481 Instruction manual

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
.stnemeriuqergnidnuorgdnagniriwrofsedoclacirtcelelacoltlusnoc,gnillatsnierofeB.1:SETON
2. READ AND SAVE THESE INSTRUCTIONS.
T0481
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Hardware Package (included):
Turn off the power at fuse or circuit box
Turn on the power at fuse or circuit box
Installation Steps
181210
1. Unscrew the finial and the rubber pad on the upper cover.
2. Unscrew set screws and remove the threaded pipe and iron
plate from the metal frame.
3. Gently place four glass panels into the metal frame,
then press the clips to secure the glass panels. (Fig.1)
1. Unscrew the finial and the rubber pads on the upper cover.
2. Unscrew set screws remove the threaded pipe and iron plate
from the metal frame.
3. Gently place four glass panels into the metal frame,
then press the clips to secure the glass panels.
(Fig.1)
4. Attach the candle tubes onto the sockets.
5. Install three bulbs (not included). See relamping label
at socket area or packaging for maximum allowed wattage.
6. Pull out the wires and grounding wire from the
post. Make wire connections using the wire
connectors (B):
---The black wire from the fixture to the black
wire from the post.
---The white wire from the fixture to the white
wire from the post.
---The grounding wire from the fixture to the
grounding wire from the post.
Carefully put the wires back into the post.
7. Place the fitter on the post, then secure it with the fitter screws (A).
CAUTION: With silicone caulking compound, caulk completely around where the fitter meets with the post
surface to prevent water from seeping into the post.
Wire Connector (B)
Fitter Screw (A)
Fig.1
Glass Panel
Clip
Metal
Frame
Bulb Type B Max.60W
(not included)
Metal Frame
Socket
Candle Tube
Iron Plate
Set Screw
Threaded Pipe
Glass Panel
Rubber Pad
Upper Cover
Finial
Grounding Wire
Fixture Wire
Wire Connector (B)
Post
Fitter
Photocell
Fitter Screw (A)
4. Attach the candle tubes onto the sockets.
5. Install three bulbs (not included). See relamping label
at socket area or packaging for maximum allowed wattage.
6. Pull out the wires and grounding wire from the post.
Make wire connections using the wire connectors (B):
---The black wire from the fixture to the black wire from the post.
---The white wire from the fixture to the white wire from the post.
---The grounding wire from the fixture to the grounding wire from the post.
Carefully put the wires back into the post.
7. Place the fitter on the post, then secure it with the fitter screws (A).
CAUTION: With silicone caulking compound, caulk completely around where the fitter meets with the post
surface to prevent water from seeping into the post.

Turn on the power at fuse or circuit box
Assembly Kit
6048MM (1SET)
The following parts are available for re-order if damaged or missing.
Spare Parts List:
181210
A:9"
B:16-3/4"
B
A
Glass Shade
10066RG (4PCS)
1. Turn off the power at the fuse or circuit box before starting installation.
2. Unthread the fitter screw and plate, and then Loosen the wire connectors connected with the
wires from photocell. (See Fig.2)
Note: Do not move the photocell to prevent water from seeping into the outlet box.
3. Take a white pigtail and black pigtail and make wire connections using wire connectors (B) : (See Fig.3)
a. The black wire from the fixture to one end of the black pigtail.
b. The white wire from the fixture to one end of the white pigtail.
c. The other end of the black pigtail to the black wire from the power source.
d. The other end of the white pigtail to the white wire from the power source.
Put all wires back into the back plate of the fixture.
Operation the Unit Without Photocell
Photocell
White Wires From
Photocell
Wire Connector
Wire Connector (B)
Black Wire From
Fixture
Wires From Fixture
Wires From
Main Power
White Pigtail
Pigtail
Red Wires From
Photocell
Black Wires From
Photocell
Fig.2 Fig.3
White Wire From
Fixture
Plate
Fitter Screw
Photocell
Wire Connector
Black Wire From
Fixture
White Pigtail
Fig.2
Plate
Washer
Hex Nut
Wire Connector (B)
Fitter Screw (A)