vds BEV 2 Technical document

AUTOMATION
FOR BARRIERS
WARNING!! Before installing, thoroughly read this manual that is an integral
part of the pack
The CE mark conforms to European directive
EEC 89/336 + 92/31 + 93/68 D.L. 04/12/1992 N. 476.
Our products if installed by qualified personnel capable to evaluate risks,
comply with norms UNI EN 12453, EN 12445

BEV2 BEV2
FAST VERSION
PACKING CONTENTS ........................................................................
2
TECHNICAL DATA...............................................................................
2
DIMENSIONS ......................................................................................
3
CONSIDERATIONS FOR INSTALLATION..........................................
3
INSTALLATION....................................................................................
4-5-6
TROUBLESHOOTING..........................................................................
7
SAFETY PRECAUTIONS ................................................................... 8
1- BARRIER
1- BAR SUPPORT
1- UNLOCKING KEY
1- CONDENSER (230Vca)
PACKING CONTENTS
Maximum length of bar 6 mt 4 mt
Motors power supply 230Vac 24Vdc 230Vac 24Vdc
Motor power 250 W 60 W 250 W 60 W
Motor RPM 1400 1800 1400 3000
Condenser 12,5 µF / 12,5 µF /
Mechanical unlock for emergency manoeuvre Mechanical
Working temperature -20° C / +55° C
Weight 50Kg
Protection rating IP 44
Limit switch Electromechanical
Opening time 10 sec 5 sec
TECHNICAL DATA

DIMENSIONS
2000-6000
377 mm
275 mm
340 mm
1090 mm
FITTING AND HOUSING FOR ACCESSORIES
Backup battery
2x12V 7Ah
only for BEV 2-24V
Control
panel
Flashing + limit
switch
Key selector
Photocell
Column

INSTALLATION
CONSIDERATIONS FOR INSTALLATION
Set up an electrical multi-duct conduit in the middle of the foundation of the barrier,
corresponding to the central hole (corrugated - diameter 25 - 50mm).
Provide a channel for electrical safety photocells or use photocells battery.
MOUNTING THE BARRIER
Unscrew the two side screws of the upper cover, and remove it; unscrew the four
fastening screws of the stainless steel carters, removing the front carter in an
upwards direction.
Place the barrier on the floor plate and fasten it with the self-locking M12 nuts
supplied.
MANUAL RELEASE
The manual release is mechanical on the
crankshaft, also accessible from the outside.
To release the operator to rotate the cover
plug and insert the supplied key into the
support on the end of the motor shaft and
screw clockwise until it stops, ending the
release maneuver. Hole
cover.
Release
key.
ŸThe installation and testing operations must be performed by qualified personnel
in order to guarantee the proper and safe operation of the automatic gate.
ŸThe company declines any responsibility for damage caused by incorrect
installations due to incompetence and/or negligence.
INSTALLATION WITH BASE PLATE (OPTIONAL)
Take the floor plate and bend the brackets as needed. Dig a suitably sized hole in
the ground. Insert the electrical conduit into the cable conduit hole of the floor plate.
Level and cement the floor plate.

SXDX
SHAFT SUPPORT
Insert the bar support on the
shaft and fasten it with
screws
Insert the bar in the support
and tighten the screws
To change the direction of opening from the left (standard) to the right proceed as
follows:
OPENING DIRECTION
ŸRelease the spring
ŸRemove the trapezoidal bracket
by unscrewing the two screws.
ŸChange the position of the key
from position Ato position B
Screws
key
Position A
Trapezoidal
bracket
A
B
Position B
Key
Screw
Screw
Bar support
Screw
Shaft

ŸReplace the trapezoidal
bracket and tighten the
screws
ŸHook the spring in the
opposite position
(holes B)
key
Position B
Trapezoidal
bracket
Holes B
key
Position B
Microswitch
electric limit
switches
Adjustment screw
for the mechanical
limit switches
SPRING REGULATION
LIMIT SWITCHES REGULATIONS
It’s possible to adjust the limit switches
position, both the mechanical
(placed inside the barrier)
and electrical ones (easily accessible,
as they are placed under the superior
cover).
N.B. When one of the mechanical
end-stroke switches is repositioned,
it is necessary to relocate the
electronically controlled one
accordingly, and then repeat the
stroke selecting procedure
ŸRelease the operator
ŸActing on the lower tie nut, put the
spring in tension until the rod is
balanced at 45° and the trapezoidal
bracket will remain horizontal to the
ground.
ŸBlock the motor
The trapezoidal bracket has four holes
which regulate the force of the spring
according to the length of the bar.
The force of the spring is reduced the
more it is placed internally.Nut
Spring adjustment
holes.
Right side
spring adjustment
holes.
Left side
Bottom
rod
Trapezoidal
bracket

PROBLEM PROBABLE CAUSE SOLUTION
On giving a command
with the remote
control or with the
key-switch, the barrier
doesn’t open or the
motor doesn’t start
230 volt mains voltage
absent
Check master switch
Emergency STOP
present
Check for any STOP
selectors or commands.
If not used, check jump-
er on STOP contact in-
put on the control board
Fuse blown
Replace with one of
same value.
Power cable of motor or
motors not
connected or faulty.
Connect the cable to
appropriate
terminal or replace.
The photocell is not
functioning or the
beam is interrupted
Check the connection,
remove any
obstacle across the
beam
On giving a command
with the remote control,
the barrier doesn’t open
but
works with the key
command
The remote control has
not been
memorised or the bat-
tery is flat
Carry out the remote
control learning
procedure on the radio
receiver or replace the
battery with a new one..
The barrier starts, but
stops immediately
The force of the motor or
motors is insufficient
Modify the value with the
FORCE trimmer on the
control unit
N.B. - If the problem persists, contact your Retailer or the nearest Service
Centre
TROUBLESHOOTING
All products are guaranteed for 2 years, as per the date on the invoice or on the receipt.
The warranty also does not include: failures or damages caused by faults of the electrical
system and/or carelessness, negligence or inadequacy of the installation to the use for
which it is intended and in any case from abnormal use; failures or damages due to
tampering by unauthorized personnel or the use of components not attributable to the
manufacturer and/or non-original spare parts; defects caused by chemical agents, external
bodies or atmospheric and/or natural phenomena in general; failures or damages caused
by incorrect installation of the Products according to the rule of art, safety and conformity
of use expressly indicated in the technical documentation of the same Products; the
consumables; interventions for checks and assessments of any flaws or defects then not
found; compensations for the period of inactivity of the system where the Products are
installed.

Rev. 4-05/14 ING
The data and images are for guidance only
VDS reserves the right to change at any time characteristics of the products described in
its sole discretion, without notice.
SAFETY PRECAUTIONS
These warnings are an essential, integral part of the product and must be given to the user. They
provide important indications on the installation, use and maintenance and must be read carefully.
This form must be preserved and passed on to subsequent users of the system.
The incorrect installation or improper use of the product may be dangerous.
INSTALLATION INSTRUCTIONS
• The installation must be performed by professionally skilled personnel and in compliance with
current local, state, national and European legislation.
• Before beginning the installation, check the integrity of the product.
• The laying of cables, electrical connections and adjustments must be workmanlike performed.
• The packing materials (cardboard, plastic, polystyrene, etc.) are a potential hazard and should
be disposed of correctly and not left within reach of children.
• Do not install the product in potentially explosive environments or environments disturbed by
electromagnetic fields. The presence of inflammable gases or fumes is a grave danger to
safety.
• Set up a safety device for overvoltage, a disconnecting and/or differential switch suitable for
the product and conforming to current standards.
• The manufacturer declines any and all responsibility for product integrity, safety and operation
in the event incompatible devices and/or components are installed.
• Solely original spare parts should be used for repairs and replacements.
• The installer must provide all the information relating to the operation, maintenance and use of
the individual parts, components and system as a whole.
WARNINGS FOR THE USER
• Read the instructions and enclosed documentation carefully.
• The product must be used for the express purpose for which it was designed. Any other use is
considered improper and therefore hazardous. In addition, the information given in this
document and in the enclosed documentation may be subject to modifications without prior
notice. It is given as an indication only for product application. The company declines any
responsibility for the above.
• Keep products, devices, documentation and anything else provided out of reach of children.
In the event of maintenance, cleaning, breakdown or faulty operation of the product, cut off the
power and do not attempt to operate on the product. Contact solely the professionally skilled
personnel responsible for these operations. Failure to adhere to the above indications may be
dangerous.
Via Circolare p.i.p. N° 10
65010 Santa Teresa di Spoltore (PE) - ITALY
Tel. [phone] - FAX [phone]
www.vdsautomation.com - [email protected]