Vdwall DS2-4 Operational manual

DS2-4 User Manual
DS2-4
Splitter + Sending Cards Box Two In One
Product User Manual

DS2-4 User Manual
2
Contents
Chapter1 Safety Precautions...................................................03
Chapter2 Item List...................................................................04
Chapter3 Product Introduction................................................05
Chapter4 Hardware Connections............................................06
4-1 Rear Panel Signal Port D iagram............................06
4-2 Typical Application Connection Diagram.......................06
4 - 3 S e n d i n g C a r d s I n s t a l l a t i o n I n s t r u c t i o n . . . . . . . . . . . . 0 7
4-4 Specifications.................................................................07
4 - 5 I n s t a l l a t i o n D i m e n s i o n D i a g r a m . . . . . . . . . . . . . . . . . . . . . 0 8
Appendix Manual Modification Record List.................. 11

DS2-4 User Manual
3
Chapter1 Safety Precautions
Danger
There is high voltage in the processor, to prevent any unexpected
hazard, unless you are maintenance personnel, please do not open the
cover of the device.
Warning
1. This device shall not encounter water sprinkle or splash,
please do not place anything containing water on this device.
2. To prevent fire, keep this device far from any fire source.
3. If this device gives out any strange noise, smoke or smell,
please immediately unplug the power cord from receptacle, and
contact local dealer.
4. Please do not plug or unplug DVI signal cable if the device
is powered on.
Caution
1. Please thoroughly read this manual before using this device,
and keep it safe.
2. In the event of lighting or when you are not going to use the
device for a long time, please pull the power plug out of
receptacle.
3. Nobody other than professional technicians can operate the
device, unless they have been appropriately trained or under
guidance of technicians.
4. To prevent equipment damage or electric shock, please don’t
fill in anything in the vent of the device.
5. Do not place the device near any water source or anywhere damp.
6. Do not place the device near any radiator or anywhere under
high temperature.
7. To prevent rupture or damage of power cords, please handle and
keep them properly.
8. Please immediately unplug power cord and have the device
repaired, when
1) Liquid splashes to the device.
2) The device is dropped down or cabinet is damaged.
3) Obvious malpractice is found or performance degrades.

DS2-4 User Manual
4
Chapter2 Item List
Please unpack the product carefully, then check whether all the following
things are included in the package. If anything is found missing, please
contact the dealer.
Standard accessories
The accessories supplied with this DVI distributor may differ from the figures
contained in the User’s Manual, but they are applicable for the regions where
you live.
1.5m power cord * 1
0.5m DVI cable *2
User manual * 1

DS2-4 User Manual
5
Chapter3 Product Introduction
The DS2-4 is a two-in-one product that combined DVI splitter and sending
cards box. It is built-in two one-in-two-out ultra HD DVI splitters, it supports any
DVI input signal with dot frequency below 165MHz; the DS2-4 also has
sending cards installation position, it can be built-in four pcs of two network
ports sending cards. The DS2-4 is very suitable for matching with VDWALL
splicing equipment such as LVP8601, LVP909, etc, it provides stable and
reliable DVI signal for the cascading of dual sending cards. Every DVI input of
DS2-4 contains DVI EDID, it can also be used for the distribution applications
of graphics card DVI signal.

DS2-4 User Manual
6
Chapter4 Hardware Connections
4-1 Rear Panel Signal Port Diagram
3
3
1
2
1
2
Diagram 4-1 Rear Panel Signal Port Diagram
1：DVI Input Port 2：Two DVI Output Ports 3：Sending Cards Installation
Position
4-2 Typical Application Connection Diagram
Diagram 4-2 Typical Application Connection Diagram
LED display
Monitor
Ethernet cable
Video camera
PC

DS2-4 User Manual
7
4-3 Sending Cards Installation Instruction
4-4 Specifications
Input signal index
Quantity / type
2×DVI（VESA）
DVI format
PC（VESA standard ）
Dot frequency ＜
165MHz
Input port
DVI：24+1 DVI_D
Signal amplitude
impedance
TMDS= 0.5 V（p_p）/ 75Ω
DVI EDID format
640x480_60/72/75
800x600_60/72/75
1024x768_60/70/75
1152x870_75
1280x720_60
1280x800_60
1280x1024_60/75
1366x768_60
1440x900_60
1600x1200_60
1680x1050_60
1920x1080_50/60
Loosen the panel screws
and draw out the
sending card tray.
Install the sending card
Plug in the
sending card
cable and
push the tray
into the
chassis
Tighten the screws, complete installation

DS2-4 User Manual
8
4-5 Installation Dimension
Diagram 4-4 Installation Dimension Diagram
1280x960_60
1920x1200_60
Output signal index
Quantity / type
4×DVI
DVI format
PC（VESA standard）Dot frequency ＜165MHz
Output port
DVI OUT：24+1 DVI_D
Others
Input voltage
100-240VAC 50/60Hz
Power consumption
≤25W
Environment
Temperature
0-45 ℃
Environment
Humidity
15-85%
Dimension
483(L)X150(W)X44(H) mm
Weight
G.W: Kg, N.W: 1.9Kg