Vdwall LVP615 series Instruction manual

地址：深圳市南山区科技园北区同方信息港 C栋5B 网址：www.videowall.cn
电话：[phone] 传真：[phone]
LVP615 系列快速使用指南
LVP615 serial quick user guide V1.0
In order to make sure users can quickly use LVP615 serial LED video processor, we prepared
the<LVP615 serial quick user guide>. About LVP615 deeply setup, adjustment and operation,
please refer to <LVP615 serial user manual>.
Front\rear panel button introduction
Front panel button
1
○
1input signal selection keys：used to select corresponding input signals.
V1，V2/YPbPr，VGA1，VGA2，HDMI，DP，DVI，EXT.
○
2setup key：used to set LVP615 parameters
Setup
Enter menu
knob
rotate knob can change current
setup item parameters
press knob （OK key)to save
parameters.
↑，↓
Select setup items
Menu return key
○
3 other function keys
Auto
VGA auto adjustment
C/F
switching effect selection key
Take
Switch signals under
Pre+Take switching
mode
M1，M2，M3
PIP/PBP display mode key
Brt+ Brt-
Output brightness
adjustment key
On/Off
PIP/PBP function on/off key
Bypass
Full and part display
mode and switching key
Mosaic
Mosaic function on key
Freeze
Output image freeze key
○
4remote sensing window：built in infrared receiver
2
3
3
3
4

地址：深圳市南山区科技园北区同方信息港 C栋5B 网址：www.videowall.cn
电话：[phone] 传真：[phone]
LVP615 系列快速使用指南
Rear panel button
1）video signal input ports 2）audio signals input and output 3）video signal outputs 4）
communication ports 5）sending card installation location
Step 1 ： sending card installation
1) Take out LVP615 processor, unscrew the sending card baffle screws and pull out the sending
card tray.
2) Install the sending card on the corresponding location of sending card tray and tighten the
screws.
3) Connect sending card +5 power cable and push the tray into the box.
4) Tighten the baffle screws. Then finish sending card installation.

地址：深圳市南山区科技园北区同方信息港 C栋5B 网址：www.videowall.cn
电话：[phone] 传真：[phone]
LVP615 系列快速使用指南
unscrew the screws
and pull out the tray
Install sending card
connect power
cable and push
the tray into the
box.
Tighten the fixed screws and finish
installation
Step 2 ： connect input and output signals
1) Turn off the power of all signal source devices.
2) Connect the output signals from video sources to corresponding video input ports of LVP615.
3) Connect LVP615 DVI outputs to DVI inputs of sending cards.
4) Connect sending card RJ45 cables to LED receiving cards .
5) Connect LVP615 VGA output to LCD display(used as monitor).
Refer to follow connection diagram：

地址：深圳市南山区科技园北区同方信息港 C栋5B 网址：www.videowall.cn
电话：[phone] 传真：[phone]
LVP615 系列快速使用指南
Connection diagram
Step 3 ： Connect power and power on
1) Make sure all input and output connection correct.
2) Connect power to LVP615 and turn on it.
3) Power on the video source devices.
Step 4 ： input signals selection
After turn on LVP615, LCD will show as below. Press input signal key to choose corresponding
input signal.

地址：深圳市南山区科技园北区同方信息港 C栋5B 网址：www.videowall.cn
电话：[phone] 传真：[phone]
LVP615 系列快速使用指南
Input： HDMI
In status： 1080p_60Hz
--------------------------------------
Output size： 1920x1080
Output start： （0，0）
--------------------------------------
Switch mode： one key SW
Switch time： 1.5sec
Step 5 ： output resolution setup
When turn on LVP615,
1) Press Setup key，then press knob （OK），LVP615 enter setup menu and press ↑,↓to select
corresponding setup menu. Press knob（OK）to enter. Press back to last item. Rotate
knob to select language“中文”or “English”and press OK to save.
2) Enter setup menu：1.out image

1.1 resolution，and rotate knob to change output resolution.
Select output resolution which is bigger than LED real resolution and press OK to save.
3) Processor will restart automatically to apply for new output resolution.
Step 6 ： output image width and height setup
After LVP615 restart
1) Press Setup，then press OK to enter setup menu 1.out image

1.2out width，rotate knob
to change the output width value to the actual pixel value of LED screen and press OK to save.
2) Then press ↓ enter 1.3 out height ，and rotate OK to change the output height value to the
actual pixel value of LED screen. Press OK to save.
3) Press to exit setup menu.
Step 7 ： computer resolution setup
1) Enter computer graphic card control interface, In setting up multiple monitors, select mode

地址：深圳市南山区科技园北区同方信息港 C栋5B 网址：www.videowall.cn
电话：[phone] 传真：[phone]
LVP615 系列快速使用指南
“ copy” “ extend” or “ dual display “ .
2) Set the monitor resolution as the same of LVP615 output resolution. The LVP615 LCD will
display current computer resolution.
Step 8 ： part / full display （ Bypass ）
1) Press DVI key to select DVI input signal. Make sure DVI input resolution is bigger than the
LVP615 output width and height.
2) Press Bypass key and indicator on, LED screen is under part pixel to pixel display situation.
Picture is not compressed.
3) Then press Bypass key and indicator off, LED screen is under full display situation. Picture
is compressed to display whole on the LED screen.
Step 9 ： turn on PIP / PBP
1) In single picture display state, press signal key to select background signal.
2) Press ON/OFF key, LCD will show：PIP=？
3) Select signal key to select PIP/PBP signal to enter dual pictures display.
4) LVP615 can presave 3 different kinds of PIP/PBP mode, Press mode key“M1~M3” to select.
5) Under PIP / PBP on state,Press ON/OFF key to turn off PIP/PBP function. LED screen will
show single picture.
Step 10 ： setup PIP / PBP parameters
1) After turn on PIP/PBP, press Setup，then press OK，LVP615 enter PIP/PBP setup menu.

地址：深圳市南山区科技园北区同方信息港 C栋5B 网址：www.videowall.cn
电话：[phone] 传真：[phone]
LVP615 系列快速使用指南
D.PIP/PBP Mode=M1
--------------------------------------
D.1 PIP width 640
D.2 PIP height 320
D.3 PIP H_start 16
D.4 PIP V_start 16
D.5 Main width 1920
D.6 Main height 1080
D.7 Main H_start 0
D.8 Main V_start 0
2) PressM1~M3 to select needed set mode, press↑↓ to select needed set items and rotate knob
to change parameters. Press OK to save parameters and finish PIP/PBP setup.
Appendix: modify the record table
Version
Time
Description
Draft
V1.0
2017.5.9
the first release
Lts